BEST T92381_A Switch Reader Add-On Installation Guide

Switch™ Reader Add-On
Installation Instructions

TOOLS NEEDED

| |
---|---|---
Drill|

Drill Bits
• 0.366 (Letter U)
• 0.136 (#29)

| Safety Glasses
| |
Screwdrivers
• #2 Phillips| • Tamper Proof Torx T8| • 1/64 Slotted
|
Center Punch| Tape Measure

OVERVIEW

Features

• Operating temperature range: -35°C to +66°C or -31°F to +151°F
• IP Rated: IP56

NOTE: Available wire lengths to connect to provided 18″ harness:

• 011-518290: 10″ (sold separately)
• 011-518290: 25″ (sold separately)
• 011-518290: 50″ (sold separately)

A Cover-Control Circuit Board and Harness Assembly
B Mounting Plate
C Gasket
D Main Control Circuit Board
E Flat Head Undercut Tamper Proof Screw Torx Drive T8: 4-40 × 1/4″
F (2x) Self-Tapping Screw Pan Head Stainless Steel Phillips Drive #2: 8-32 × 1/2″

Switch Reader Add-On Installation Instructions

CONSIDER MOUNTING PLACEMENT.
NOTE: The placement of the Switch Reader Add-On will vary from application o application based on the environment and aesthetic preference.
Consider the mounting placement of the Switch Reader Add-On by placing the reader beside, above, or below the existing reader.

Place beside the existing reader.

Place above or below the existing reader.

Switch Reader Add-On Installation Instructions

PREPARE SURFACE.
NOTE: For the provided mounting screws F (2x), adjust as needed depending on the surface and the hardware.
NOTE: The provided mounting screws F (2x) will not cover all installation scenarios due to certain surface compositions such as brick, drywall, or other materials. Ensure that the correct drill bits, mounting screws, and screw anchors are purchased and used to meet the needs of each individual application.
WARNING: Take proper precautions when installing the Switch Reader Add-On .

NOTE: Mounting plate (B) may be used as a drilling template.

1. Prepare the surface by ensuring the surface is clean and smooth.
2. Using the mounting plate (B) as a template, place and correctly orient the mounting plate (B) onto the surface.
3. Use a center punch tool to mark holes a, b, and c.
4. Drill holes.

FASTEN MOUNTING PLATE AND GASKET TO SURFACE.

REMINDER: Install the mounting plate (B) to a clean and smooth surface using appropriate hardware.

RUN HARNESS THROUGH MOUNTING PLATE AND GASKET.

NOTE: Carefully thread the harness through the mounting plate (B), gasket (C), and into the wall cavity to avoid damaging other components housed in the wall.

INTERLOCK COVER HOOK WITH MOUNTING PLATE TAB.

SECURE COVER WITH TAMPER-PROOF SCREW.

CONNECT READER/HARNESS ASSEMBLY TO MAIN CONTROL CIRCUIT BOARD.

NOTE: The main control circuit board should not be placed where it will be exposed to external environmental conditions such as water, rain or extreme temperature.

SWITCH READER ADD-ON TO MAIN CONTROL CIRCUIT BOARD

ID| 5V| GND| D+| D-
Position| 1| 2| 3| 4
Wire Color| RED| BLACK| WHITE| GREEN

CUT EXISTING ACCESS CONTROL WIRE AND RECONNECT TO SWITCH READER ADD-ON

MAIN CONTROL CIRCUIT BOARD.

NOTE: The existing building site’s reader, access control wiring, and panel placement will vary in each installation.

FCC/IC Certification

Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
( 1 ) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Hardware Manufacturer: dormakaba) could void the user’s authority to operate the equipment.

WEEE

This symbol means that you must dispose of an electrical item AND/OR containing in it a Li-Mn battery separately from general household waste when they reach the end of their useful life. Take your PC or the battery to your local waste collection point or center. This applies to all countries of the European Union, and to other countries with a  separate waste collection system.
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user  is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Statement
THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCE-EXEMPT RSS STANDARD(S).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference,  including any interference that may cause undesired operation of the device.

WARNING: Changes or modifications not expressly approved by dormakaba could void the user’s authority to operate the equipment.

https://dhwsupport.dormakaba.com/hc/article_attachments/360084974254/T92387.pdf
For Online Instructions Visit:
https://dhwsupport.dormakaba.com/hc/en-us
For Assistance or Warranty Information:
Call 1-800-392-5209 or visit
https://dhwsupport.dormakaba.com/hc/en-us

BEST is a trademark of dormakaba USA Inc. ©2021 All rights reserved.
T92381_A

Documents / Resources

| BEST T92381_A Switch Reader Add- On [pdf] Installation Guide
1SWRDR, T8H-1SWRDR, T8H1SWRDR, T92381_A, Switch Reader Add-On
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>