VISTATECH NV-07001 Wireless Audio Receiver / Transmitter Instruction Manual
- June 6, 2024
- VISTATECH
Table of Contents
VISTATECH NV-07001 Wireless Audio Receiver / Transmitter
Instruction Manual
Product Introduction
This compact wireless 3.5mm audio adapter lets you manage audio signals freely according to your needs. All devices with an AUX 3.5mm audio port are supported – the possibilities are limitless!
Receiver mode
When used as a wireless receiver, the RX-TX-10 transforms any traditional car
or home system with an AUX connection into a contemporary piece of audio
equipment. Use it in this mode to play music from a smartphone on your trusty
non-Bluetooth stereo system.
Transmitter mode
As a transmitter, this Bluetooth audio adapter allows you to send audio from a
device with an AUX port to any Bluetooth headphones or set of speakers. Use it
in this mode to cast TV audio to your wireless headset when gaming or
binge-watching your favourite series late at night.
Specification
- Bluetooth version: 5.0
- Bluetooth frequency: 2.402-2.480GHz
- Bluetooth protocol support: A2DP and AVRCP
- Support multi-format decoding. MP3, WAV, WMA, APE, FLAC
- Transmission distance: > 20M (open place)
- Charge input voltage: DC 5V
- Power supply: 3.7V
- Power consumption: play in less than 20mA, standby in 0.64 – 4.5mA, shut down in 2 microamps
- Battery capacity: 200mAh
- Working time: about 3 – 5 hours
- Charging time: 2 hours
- Signal-Noise Ratio: more than 95db
Package
- 2 in 1 Wireless Audio Transmitter Receiver
- Instruction Manual
- USB charging cable
- 3.5mm audio cable
Charging
The 2 in 1 Wireless Audio Transmitter Receiver has built-in rechargeable
battery for long standby and use time. It is recommended that you fully charge
before its
first-time use.
- Plug one end of the Micro USB charging cable into the 2 in 1 Wireless Audio Transmitter Receiver charging port. The other end plugs into any standard USB power outlet (such as the phone charger, computer USB interface).
- Charging time is approximately 2 hours
- The red light is on when charging. The red light is off after fully charged.
- Music transmission is still available when charging.
Operation
Receiving mode:
- Connect to your Non-wireless speaker or headphones to the 2 in 1 Wireless Audio Transmitter Receiver RX audio in port via 3.5mm audio jack.
- Hold Down the power On/Off button to turn on the 2 in 1 Wireless Audio Transmitter Receiver.
- Place the 2 in 1 Wireless Audio Transmitter and the Bluetooth device that you would like to pair within the operating distance. We recommend keeping the two devices no further than 10 feet apart.
- Ensure Bluetooth is enabled on your phone or music device. Refer to the manufacturer’s instructions for how to enable Bluetooth on your device.
- Once you have activated Bluetooth on your device, select the “RX-TX-10” from the list of available Bluetooth devices.
Transmitting mode:
- Connect to your sound or music source to the 2 in 1 Wireless Audio Transmitter Receiver TX audio in via 3.5mm audio jack.
- Turn on the music source device.
- Hold down the power On/Off button to turn on the 2 in 1 Wireless Audio Transmitter Receiver.
- To activate the transmitter mode, press Vol + and Vol – buttons at the same time upon powering on the device.
- Turn on your Bluetooth device, ensure it is in pairing mode.
- 2 in 1 Wireless Audio Transmitter Receiver will automatically connect with your Bluetooth device.
In Receiving mode:
You can Hold down + or – to adjust the volume. Short press + for next track or
– for previous track.
FCCCaution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/tv technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>