SEKONDA IS47B Men’s Watch User Guide
- June 4, 2024
- SEKONDA
Table of Contents
SEKONDA IS47B Men’s Watch
- EL Backlight
- Stopwatch
- Calendar
- 100M Water Resistant
- Quartz Movement
- Alarm
- Chime
- Battery(CR2025 +SR626SW)
BUTTONS
Button operations are indicated using the letters shown on the below illustration.
- A – Reset
- B Mode
- C EL backlight
- D — Start/ Stop
DISPLAY
The screen is shown below
ATTENTION
- Never try to open the case or remove its back cover
- Do not operate buttons underwater.
- Should moisture appear inside the watch, have it checked immediately by your dealer. Otherwise it can cause erosion of the metal parts of the watch.
- lthough the watch is designed to withstand normal use, you should avoid rough use or dropping the watch.
- Avoid exposing the watch to extreme temperatures.
- Wipe the watch with a dry and soft cloth only. Avoid allowing it to come into direct contact with chemical materials, which can cause deterioration of the plastic parts of the watch.
- Avoid wearing the watch in electromagnetic or static conditions.
MODE SELECTION
Press “B” to change the mode in the following sequence:
Timekeeping Mode: Stopwatch Mode Alarm Mode Time Setting Mode.
TIMEKEEPING
- Date display
- Alarmand chime setting
- (Timekeeping icon changes in accordance with the day of the week).
STOPWATCH
- 1/100 second unit;
- Measuring range: o’00″00 23:59’59”.
ALARM
- The alarm sounds at the preset time each day;
- Hourly time signal;
- 5 minute snooze
TIME SETTING
- 12Hr and 24Hr formats.
- Hour, Minutes, Seconds, Month, Date and Day of the week can be set.
ADJUST HANDS
Pull the crown out and turn to adjust the hour and minute hands; Push the crown back in to the normal position after the time is set;
TIMEKEEPING
Display The Date
In the timekeeping mode, press and hold “D” to display the date.
On/Off The Alarm
- In the timekeeping mode, press and hold “A” to display the alarm time;
- Press “D” at the same time to on/off the alarm.
On/Off The Chime
- In the timekeeping mode, press and hold “A” to display the alarm time;
- Press “B” at the same time to on/off the chime.
ALARM
Alarm Time Setting
- In the alarm mode the hour will begin to flash.
- Press “D” to increase the hour, press and hold “D” to increase at high speed;
- Press “A” to select the minutes;
- Press “D” to increase the minutes, press and hold “D” to increase at high speed;
- Press “B” to return to the timekeeping mode, after you set the alarm. The alarmon/off directions are located on page three.
Snoozee
- The alarm sounds at the preset time each day for about 60 seconds.
- Press “D” to snooze the alarm for 5 minutes;
- Press “A” to stop the alarm.
STOPWATCH
A Lap Time
- In the stopwatch mode, press “D” to start the stopwatch;
- To stop the stopwatch press “D” again;
- Press”A” to reset the stopwatch.
Split Time
- In the stopwatch mode, press “D” to start the stopwatch;
- Press “A” to display the split time, the stop watch will continue timing internally;
- Press “A” to clear the split time and continue time measurement;
- Repeat step 2 and 3 to measure multiple split times;
- Press “D” to stop the stopwatch.
- Press “A” to reset the stopwatch.
Alwaysreset the stopwatch afteruse.
TIME SETING
Time Setting
- In the time setting mode the seconds will begin to flash.
- Press “D” to reset the seconds;
- Press “A” to change to the next selection;
- Press “D” to increase the number, press and hold “D” to increase at high speed;
- Repeat step 3 and 4 to change the selection in the following sequence: Seconds Minutes Hour – Date Month-Day; Both 12Hr and 24Hr formats are selected when setting the hour.
- Press “B” to return to the timekeeping mode.
BACKLIGHT
The backlight uses an electro-luminescent that causes the display to glow for
easy reading in the dark.
Using The EL Backlight
In any mode, press “C” to illuminate the display for about 3 seconds.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>