SONY FW-100BU40J LCD Display Installation Guide

SONY FW-100BU40J LCD Display Installation Guide

To Customers
Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable for any damages or injury caused by mishandling or improper installation, or installing any other than the specified product. Your Statutory Rights (if any) are not affected.

WARNING

If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or fire.

This instruction manual shows the correct handling of the product and important precautions necessary to prevent accidents. It is your responsibility to read, thoroughly understand, and follow all instructions in this instruction manual. Failure to do so may result in serious personal injury or property damage, and may void the warranty. Keep this manual available for future reference.

To Sony dealers
Sufficient expertise is required for installing this product. Be sure to read this manual thoroughly to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or improper installation. Please give this manual to the customer after installation.

On Safety

Products by Sony are designed with safety in mind. If the products are used incorrectly, however, it may result in a serious injury through fire, electric shock, the product toppling over, or the product dropping. Be sure to observe the precautions for safety to prevent such accidents.

CAUTION

Specified products

The following products are subject to change without notice, may be out of stock, or discontinued.
Some models may not be available in certain regions.

LCD Display| FW-100BU40J FW-75BU30J FW-65BU30J FW-55BU30J FW-50BU35J FW- 50BU30J FW-43BU35J FW-43BU30J FW-32BU30J FW-100BZ40J FW-75BZ30J FW-65BZ30J FW- 55BZ30J FW-50BZ35J FW-50BZ30J FW-43BZ35J FW-43BZ30J FW-32BZ30J
---|---

WARNING
If the following precautions are not observed, serious injury or death through fire, electric shock, the product toppling over, or the product dropping can result.

Be sure to read thoroughly the all safety information described in the instruction manual.

Provide adequate clearances around the LCD Display.
The following illustration shows how much space is required around the LCD Display.
Be sure to install the LCD Display in the orientation shown in the following illustration.

Landscape

Portrait

Unit: mm (inches)

• Only on limited region/country/LCD Display model.

Do not block the ventilation holes of the LCD Display.
If you block the ventilation holes with tapes or other objects, heat builds up inside the LCD Display and may cause a fire.

Others

• If you cover the LED and its surroundings with tapes or other objects, the status of the LCD Display cannot be recognized and the remote control may not work.
• When carrying the LCD Display, hold it in landscape orientation, and take care not to drop it when installing. Do not apply excessive force to the LCD Display; otherwise, it may be deformed.

Installation Style

**Model Name**

| Landscape| Portrait
---|---|---
| | **| | |
~-20°| ~-15°| 0°| ~+20°| ~-20°| ~-15°| 0°| ~+20°
FW-100BU40J / 100BZ40J| ** –| | | | –| | |
FW-75BU30J / 75BZ30J| | | | | –| | | *1
FW-65BU30J / 65BZ30J| | | | | –| 1| 2| 1
FW-55BU30J / 55BZ30J| | | | 1| –| 3| 4| *2
FW-50BU35J / 50BZ35J| | | | | | | | –
FW-50BU30J / 50BZ30J| | | 5| 2| | | |
FW-43BU35J / 43BZ35J| | | | | 3| 3| | –
FW-43BU30J / 43BZ30J| 1| 1| 5| 3| | | 2| 4
FW-32BU30J / 32BZ30J| | | | | | | |

1. Operating temperature: 39 °C and lower
2. Operating temperature: 38 °C and lower
3. Operating temperature: 37 °C and lower
4. Operating temperature: 36 °C and lower
5. Operating temperature: 38 °C and lower or provide 300 mm clearance on top of the LCD Display

Landscape Style

The length of the screw for Wall-Mount Bracket differs depending on the Wall- Mount Bracket thickness. Please refer to below illustration.

FW-100BU40J / 100BZ40J

FW-75BU30J / 65BU30J / 55BU30J / 50BU35J / 50BU30J / 43BU35J / 43BU30J / 75BZ30J / 65BZ30J / 55BZ30J / 50BZ35J / 50BZ30J / 43BZ35J / 43BZ30J

FW-32BU30J / 32BZ30J

Refer to the following table for wall-mount hole pattern.

Model Name| Wall-mount hole
pattern
---|---
FW-100BU40J / 100BZ40J| 600 × 400 mm
FW-75BU30J / 75BZ30J /
65BU30J / 65BZ30J /
55BU30J / 55BZ30| 300 × 300 mm
FW-50BU35J / 50BZ35J /
50BU30J / 50BZ30J /
43BU35J / 43BZ35J /
43BU30J / 43BZ30J| 200 × 200 mm
FW-32BU30J / 32BZ30J| 100 × 200 mm

Be sure to store the unused screws and Table-Top Stand in a safe place until you are ready to attach the Table-Top Stand. Keep the screws away from small children.

1. Remove the stand covers.
   

2. Remove the screws from the rear of the LCD Display.
   

3. Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied)
   
   When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}. Do not lift the Mounting Hook before the screws (two screws each for left/right) are secured. This may distort the Mounting Hook or the LCD Display cabinet.

4. Detaching the Table-Top Stand from the LCD Display. To detach the Table-Top Stand from the LCD Display, remove the screws .
   
   Note

   • Be careful when lifting the LCD Display as the TableTop Stand is detached, the Table-Top Stand may topple over and cause personal injury.
   • Take care when removing the Table-Top Stand from the LCD Display to prevent it from falling over and damaging the surface that the LCD Display is sitting on.
   • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the LCD Display.
   • Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the panel facingdown.
   • When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes on the rear of the LCD Display.

FW-75BU30J / 65BU30J / 55BU30J / 50BU35J / 50BU30J / 43BU35J / 43BU30J / 75BZ30J / 65BZ30J / 55BZ30J / 50BZ35J / 50BZ30J / 43BZ35J / 43BZ30J

1. Remove the screws from the rear of the LCD Display.
   
   When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}. Do not lift the Mounting Hook before the screws (two screws each for left/right) are secured. This may distort the Mounting Hook or the LCD Display cabinet.

2. Attach the Wall-Mount Attachment (supplied with the LCD Display) to the rear of theLCD Display (to make it parallel with the wall)
   Supplied with the LCD Display
   
   Note

   • Be sure to fasten the Wall-Mount Attachment when attaching them to the LCD Display. Use only a flathead screwdriver to install the Wall-Mount Attachment. Use of another tool might result in over torqueing the Wall-Mount Attachment and damaging the LCD Display.

3. Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied).
   
   Note

   • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}.

4. Detaching the Table-Top Stand from the LCD Display.
   

5. Remove one side of the Table-Top Stand at a time. Firmly hold the Table-Top Stand securely with both hands while the other people lift up the LCD Display

6. Repeat the previous step and remove the other side of the Table-Top Stand.
   Note

  * Three or more people are required to detach the Table-Top Stand.
  * Be careful not to use excessive force while detaching the Table-Top Stand from the LCD Display as it may cause the LCD Display set to fall resulting in personal injury or physical damage to the LCD Display.
  * Take care when handling the Table-Top Stand to prevent damage to the LCD Display.
  * Be careful when lifting the LCD Display as the TableTop Stand is detached, the Table-Top Stand may topple over and cause personal injury.
  * Take care when removing the Table-Top Stand from the LCD Display to prevent it from falling over and damaging the surface that the LCD Display is sitting on.
  * Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the LCD Display.
  * Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the LCD panel facing down.

FW-32BU30J / 32BZ30J only

1. Detaching the Table-Top Stand from the LCD Display.
   To detach the Table-Top Stand from the LCD Display, remove the screws.
   
   Note

   • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the LCD Display.
   • Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the LCD panel facing down.
   • Place the LCD Display with its screen facing down on a level and stable surface covered with a thick and soft cloth when removing the Table-Top Stand from the LCD Display to prevent damaging the surface of the LCD display

2. Remove the screws from the rear of the LCD Display.
   

3. Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied).
   
   Note

   • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}

Portrait Style

The length of the screw for Wall-Mount Bracket differs depending on the Wall- Mount Bracket thickness. Please refer to below illustration.

FW-100BU40J / 100BZ40J

FW-75BU30J / 65BU30J / 55BU30J / 50BU35J / 50BU30J / 43BU35J / 43BU30J / 75BZ30J / 65BZ30J / 55BZ30J / 50BZ35J / 50BZ30J / 43BZ35J / 43BZ30J

FW-32BU30J / 32BZ30J

Refer to the following table for wall-mount hole pattern.

Model Name| Wall-mount hole
pattern
---|---
FW-100BU40J / 100BZ40J| 600 × 400 mm
FW-75BU30J / 75BZ30J /
65BU30J / 65BZ30J /
55BU30J / 55BZ30J| 300 × 300 mm
FW-50BU35J / 50BZ35J /
50BU30J / 50BZ30J /
43BU35J / 43BZ35J /
43BU30J / 43BZ30J| 200 × 200 mm
FW-32BU30J / 32BZ30J| 100 × 200 mm

Be sure to store the unused screws and Table-Top Stand in a safe place until you are ready to attach the Table-Top Stand. Keep the screws away from small children.

FW-100BU40J / 100BZ40J

1. Remove the stand covers.
   

2. Remove the screws from the rear of the LCD Display.
   

3. Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied).
   
   When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}. Do not lift the Mounting Hook before the screws (two screws each for left/right) are secured. This may distort the Mounting Hook or the LCD Display cabinet.

4. Detaching the Table-Top Stand from the LCD Display.
   To detach the Table-Top Stand from the LCD Display, remove the screws .
   
   Note

   • Be careful when lifting the LCD Display as the TableTop Stand is detached, the Table-Top Stand may topple over and cause personal injury.
   • Take care when removing the Table-Top Stand from the LCD Display to prevent it from falling over and damaging the surface that the LCD Display is sitting on.
   • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the LCD Display.
   • Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the panel facing down.
   • When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes on the rear of the LCD Display

FW-75BU30J / 65BU30J / 55BU30J / 50BU35J / 50BU30J / 43BU35J / 43BU30J / 75BZ30J / 65BZ30J / 55BZ30J / 50BZ35J / 50BZ30J / 43BZ35J / 43BZ30J

1. Remove the screws from the rear of the LCD Display
   
   When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}. Do not lift the Mounting Hook before the screws (two screws each for left/right) are secured. This may distort the Mounting Hook or the LCD Display cabinet.

2. Attach the Wall-Mount Attachment (supplied with the LCD Display) to the rear of the LCD Display (to make it parallel with the wall).
   Supplied with the LCD Display
   
   Note

   • Be sure to fasten the Wall-Mount Attachment when attaching them to the LCD Display. Use only a flat head screwdriver to install the Wall-Mount Attachment. Use of another tool might result in over torqueing the Wall-Mount Attachment and damaging the LCD Display.

3. Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied).
   
   Note

   • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}

4. Detaching the Table-Top Stand from the LCD Display.

5. Remove one side of the Table-Top Stand at a time. Firmly hold the Table-Top Stand securely with both hands while the other people lift up the LCD Display
   

6. Repeat the previous step and remove the other side of the Table-Top Stand.
   Note

  * Three or more people are required to detach the Table-Top Stand.
  * Be careful not to use excessive force while detaching the Table-Top Stand from the LCD Display as it may cause the LCD Display set to fall resulting in personal injury or physical damage to the LCD Display.
  * Take care when handling the Table-Top Stand to prevent damage to the LCD Display.
  * Be careful when lifting the LCD Display as the TableTop Stand is detached, the Table-Top Stand may topple over and cause personal injury.
  * Take care when removing the Table-Top Stand from the LCD Display to prevent it from falling over and damaging the surface that the LCD Display is sitting on.
  * Do not remove the Table-Top Stand for any reasonother than to install corresponding accessories on the LCD Display.
  * Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the LCD panel facing down.

FW-32BU30J / 32BZ30J only

1. Detaching the Table-Top Stand from the LCD Display.
   To detach the Table-Top Stand from the LCD Display, remove the screws.
   
   Note

   • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the LCD Display.
   • Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the LCD panel facing down.
   • Place the LCD Display with its screen facing down on a level and stable surface covered with a thick and soft cloth when removing the Table-Top Stand from the LCD Display to prevent damaging the surface of the LCD display.

2. Remove the screws from the rear of the LCD Display.
   

3. Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied).
   
   Note

   • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}.

References

• Sony Corporation - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>