SEKONDA IS42 Leather Strap Smart Watch User Guide

SEKONDA IS42 Leather Strap Smart Watch

Service and Repairs

Your SEKONDA watch is guaranteed against defects in materials  and workmanship for a period of 2 years from the date of purchase. During this period, we will exchange or repair. at our discretion, any defective components free of charge

IMPORTANT – Not covered by Guarantee

1. Batteries. straps and bracelets
2. Damage caused by accident, misuse or lack of care
3. Water penetrations except in watches marked as ·water Resistant”
4. General wear and unauthorised repair

SERVICING AND REPAIRS UNDER GUARANTEE
Please post your watch. together with the Retailer’s Sales Receipt  or proof of purchase, the completed Guarantee slip, and a brief note to explain the nature of the fault, by Registered Post or Recorded Delivery to the address shown. Do not send the presentation box as this will NOT be returned

SERVICING AND REPAIRS OUTSIDE OF GUARANTEE
Available at a reasonable charge after an estimate has been sent by T.P. (UK) Ltd_ Send your watch to us by Registered
Post or Recorded Delivery to the address shown

Important Note

• It is important to identify your watch correctly_ If. after reading this Instruction Guide, you have any further questions regarding  the use, operation or adjustment of your watch. please call us during office hours on 0116 288 2500
• T.P. (UK) Ltd, Alexander House, Chartwell Drive, Wigston, Leicester LE18 2EZ United Kingdom.

Water Resistance

If your watch is water resistant, it will clearly state ·water  Resistant- or have a static water pressure indication (e.g  “30150/100/200 metres”) on the dial andfor case back
If it is not marked as water resistant, it should not be allowed lo come into contact with water or be worn in conditions that could expose it to moisture (eg washing, heavy rain etc.)_ Certain chemicals in water may damage the watch seals. To maintain water resistance, we recommend that your watch is serviced and re-sealed at least every 12 months by T.P. (UK) Lid

IMPORTANT
Buttons must not be operated while in contact with water

WATER RESISTANT or RESISTANT TO 30 METRES
Suitable for normal everyday use and will resist exposure to splashes and rain; it is NOT designed lo be used whilst bathing or swImmmg

WATER RESISTANT TO 50 METRES
As 30 metres plus bathing or swimming

WATER RESISTANT TO 100 METRES
As 50 metres plus pool side diving and snorkelling, but not high board or scuba diving

WATER RESISTANT TO 200 METRES
As 100 metres plus scuba diving, but not high board diving

2 eye and 3 eye chronograph with date

Resetting the chronograph function

Before setting the time please check that all chronograph hands are at the “0”/12 o’clock position.

To reset the hands to the “0”/12 o’clock position press the buttons on your watch in the following sequence:

• If the chronograph is counting then press ‘A’  to stop the chronograph and then ‘B’ to reset back to uo”.
• If split timing is displayed then press ‘B’ then ‘A’  followed by ‘B’ again to reset.
• Always push the crown back to position “1” once the above has been completed.

Setting the time

The chronograph measurement must be stopped before the time can be set.

1. Pull the crown out to position ‘2’.
2. Turn the crown clockwise until the previous date is displayed.
3. Now pull the crown out to position ‘3’ and adjust the hands to the desired time.
4. Push the crown back to position ‘1 ‘.

Do not attempt to set the date between 9:00 PM and 1 :OO AM as the date change cycle is already in  progress.

Using the stopwatch/chronograph  feature:
The chronograph measurement can time up to 60 minutes.

Standard measurement:

1. Press ‘A’ to start the chronograph liming, then press ‘A’ to stop the liming.
2. Press ‘B’ to reset the chronograph.

Accumulated elapsed time measurement:

1. Press ‘A’ to start timing, then press ‘A’ to stop the timing.
2. Restart the timing by pressing ‘A’ as many limes as required.
3. Press ‘A’ to stop the chronograph and ‘B’ to reset.

Using the stop watch/chronograph lea ture continued:
Split time measurement:

1. Press ‘A’ to start the timing, then press ‘B’ to  split the liming.
2. Press ‘B’ to release the liming as many times  as required.
3. Press ‘A’ to stop the chronograph timing.
4. Press ‘B’ to reset the chronograph.

3 eye chronograph with day and date

• Do not attempt to set the day between 11.15 PM and  6.00 AM as the day/date change cycle is already in progress.
• The chronograph measurement can time up to 4 hours, 59 minutes and 59 seconds.
  Please refer to the previous chronograph sections for function. Note that the ‘split time measurement’ function is not included for the ‘3 eye chronograph with day and date’.

Setting the time:

1. Pull the crown out to position ‘3’ and adjust the hands to the desired lime.
2. Push crown back to position ‘1’.

Setting the date:

1. Pull the crown out to position ‘2’.
2. Turn the crown anti-clockwise to set the date.
3. After the date has been set push the crown back to position ‘1’.
4. Do not attempt to set the date between 9:00 PM and 1:OD AM as the date change cycle is already in progress.

Setting the day:

1. Pull the crown out to position ‘2’ and turn the crown clockwise until the desired day is set.
2. After the day has been set, push the crown back to position ‘1’.

GUARANTEE

DATE OF PURCHASE:
Retailers stamp if required or full name and address

Please attach the receipt or proof of purchase; failure to attach these may invalidate this Guarantee. This Guarantee does not affect your statutory rights.
1S42/08-2019

PLEASE USE BLOCK CAPITALS

• NAME
• ADDRESS
• POSTCODE
• DAYTIME TELEPHONE NUMBER

IMPORTANT
This guarantee slip should be retained by the owner of the product and should be sent to Timeproducts (UK) Ltd. together with the product and £6 to cover the handling and postage when service under Guarantee is required.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>