SEKONDA IS47D Mens Digital Watch User Manual

SEKONDA IS47D Mens Digital Watch

FUNCTIONS

1. EL Backlight
2. Alarm
3. Chime
4. Stopwatch
5. CR2025 battery
6. 50m water resistant

BUTTONS

• Button operations are indicated using the letters shown on the below illustration.

• A: Light

• B: Mode

• C: Reset

• D:  Start / Stop

DISPLAY

• The screen is shown below:

ATTENTION

1. Never try to open the case or remove its back cover.
2. Do not operate the buttons underwater.
3. Should moisture appear inside the watch, have it checked immediately by your dealer. Otherwise, it can cause erosion on the metal parts of the watch.
4. Although the watch is designed to withstand normal use, you should avoid rough use or dropping the watch.
5. Avoid exposing the watch to extreme temperatures.
6. Wipe the watch with dry and soft cloth only. Avoid allowing the watch to come into direct contact with chemical materials that can cause deterioration of the plastic parts on the watch.
7. Avoid wearing the watch in electromagnetic and static conditions.

MODE SELECTION

• Press “B” to change the mode in the following sequence: Timekeeping mode Stopwatch mode Alarm mode Time setting mode.

TIMEKEEPING MODE

• Hour, minute, seconds, month, date, and day display.
• The alarm on/off.
• Chime (hourly time signal) on/off.

STOPWATCH MODE

• 1/100 second measurement.
• Split time.

ALARM MODE

• Setting the alarm.
• Snooze.

TIME SETTING MODE

• 12/24H format.
• Setting the hour, minute, seconds, month, date and day.

BACKLIGHT

• The backlight uses an electro-luminescent which causes the display to glow for easy reading in the dark.

1. In any mode press “A” to illuminate the display for about 3 seconds;

TIME KEEPING

• Always use the timekeeping mode when the stop-watch, alarm and time-setting modes are not in use.
• In the timekeeping mode the hour, minute, seconds, month, date, and day are displayed.

1. In the timekeeping mode press “D” to check the month and date.
2. Press “C” to check the alarm time.

ALARM AND CHIME ON/OFF

1. In the timekeeping mode press and hold “C”, then press “D” to turn the alarm on and off.
2. Press and hold “C”, then press “B” to turn the chime on and off.
3. (The days of the week will show when the chime is on).

STOPWATCH

1. In the stopwatch mode press “D” to start the stopwatch;
2. Press “D” to stop the stopwatch or press “B” to change the mode while the stopwatch is running. The stop -watch will continue timing in the background.
3. Once you have finished timing, press “B” repeatedly until you return to the stopwatch mode;
4. Press “D” to stop the stopwatch;
5. Press “C” to reset the stopwatch.

SPLIT TIME

1. In the stopwatch mode press “D” to start the stopwatch;
2. Press “C” to display the split time. The stopwatch will continue timing internally.
3. Press “C” to clear the split time and continue time measurement;
4. Repeat steps 2 and 3 to measure multiple split times;
5. Press “D” to stop the stopwatch;
6. Press “C” to reset the stopwatch.
7. Press “B” to change to the next mode after you have finished using the stopwatch.

ALARM

• The alarm will sound at the pre-set time each day.

1. In the alarm mode, the hour will flash. Press “D” to adjust the hour, and press and hold “D” to adjust the hour quickly;
2. (The letter A will represent AM and the letter P will represent PM time setting. The letter H will represent the 24-hour time setting).
3. Press “C” to select the minutes. The minutes will begin to flash.
4. Press “D” to adjust the minutes, and press and hold “D” to adjust the minutes quickly;
5. Press “B” to change to the next mode, after you have set your alarm. (Always ensure that your alarm is on by following step 1 under the ‘ALARM AND CHIME ON/OFF’).

SNOOZE

1. When the alarm sounds, press “D” to stop the alarm or press “B” to snooze the alarm;
2. (The alarm will sound again after five minutes to signal that the snooze period is over).
3. Press “D” to stop the snooze alarm.

TIME SETTING

1. In the time setting mode the seconds will flash, press “D” to reset the seconds;
2. Press “C” to select the minutes. The minutes will begin to flash.
3. Press “D” to adjust the minutes, press and hold “D” to adjust the minutes quickly
4. Press “C” to select the hour. The hour will begin to flash.
5. Press “D” to adjust the hour, press and hold “D” to adjust the hour quickly;
6. (The letter A will represent AM and the letter P will represent PM time setting. The letter H will represent the 24-hour time setting).
7. Press “C” to select the date. The date will begin to flash.
8. Press “D” to adjust the date, press and hold “D” to adjust the date quickly;
9. Press “C” to select the month. The month will begin to flash.
10. Press “D” to adjust the month, press and hold “D” to adjust the month quickly;
11. Press “C” to select the day. The day will begin to flash.
12. Press “D” to adjust the day, press and hold “D” to adjust the day quickly.
13. Press “B” to change to the next mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>