An Energy Technology W015CN-01 Vehicle-Mounted 15W Wireless Charging Seat User Manual
- June 6, 2024
- An Energy Technology
Table of Contents
User Manual
Product Overview
Product Introduction: This product is installed in the dashboard as part of
the electric-assisted bicycle, See the above picture.
When the user is actually using the bicycle, this product can be used for
swiping the card and charging the mobile phone, and when using time, the user
will not touch the product and should keep a certain distance, at least 20cm.
More introduction
This product offers a configurable charging mode that supports a 15W.15W power supply that meets WPC QI standard RX. Supports foreign body detection, if there is a foreign body, as a metal conductive material, between the transmitter and the receiver, the transmitter is off. Place the mobile phone in the wireless charging tray, charge the mobile phone, and stop charging after removing the mobile phone. Magnetic card into the NFC induction area when the card operation!
Product parameters
- Name: Vehicle-mounted 15W wireless charging seat
- Model: W015CN – 01 / W015CN – 10 / W015CN – XX
- Color: black
- Input voltage: DC 16V~20V
- Input current: 2A(Max)
- Output power: 15W(Max)
Characteristics
- Meet the WPC QI standard
- Support foreign body detection
- Operating temperature range: 0-35 deGC.Humidity range: 20%-80%.
- Storage temperature range: -20 — 70 deGC.Humidity range: 5%-90%.
- RoHS compliance
PRODUCT SPECIFICATIONS
Intended Use/Category | Wireless Charging |
---|---|
H-Field Strength | 50.21 dBuA/m@3m distance |
Frequency band(MHz) | 110KHz-145KHz |
Modulation | ASK |
Antenna type | Coil Antenna |
Duty cycle(%) | / |
Intended Use/Category | NFC |
--- | --- |
H-Field Strength | 17.41 dBuA@3m distance |
Frequency band(MHz) | 13.56MHz |
Modulation | ASK |
Antenna type | Coil Antenna |
Duty cycle(%) | / |
Functional description
The wireless charging input terminal VCC is connected to the 18V direct current. After the voltage is lowered by the BUCK circuit constituted by MOS tube Q1(RU30J30) and L3, it works in the full-bridge circuit constituted by Q2(RU30J30) and Q3(RU30J30). The IC(CPS8100) sends a drive signal to control the Q2(RU30J30) upper and Q3(RU30J30) lower tubes and Q2(RU30J30) lower tubes and Q3(RU30J30) upper tubes to conduct alternately so that an alternating voltage is obtained on the coil! Then through the electromagnetic induction to the receiving coil to get the voltage! The IC(CPS8100) detects current through resistor R9!
NFC Product Overview
Introduction
The FM17550 is a highly integrated Transceiver IC for Contactless
communication at13.56MHz. The FM17550 Transceiver IC support Reader/Writer
mode supports ISO/IEC14443A/B protocol.
The FM17550’s internal transmitter part is able to drive a reader/writer
antenna designed to communicate with ISO/IEC14443A/B cards and transponders
without additional active circuitry. The receiver part provides a robust and
efficient implementation of a demodulation and decoding circuitry for signals
from ISO/IEC14443A/B compatible cards and transponders. The digital part
handles the complete ISO/IEC 14443A/B framing and error detection. The FM17550
supports ISO/IEC14443A cards and transponders with transfer speeds from
106kbit/s to 424kbit/s in both directions. And can support all layers of the
ISO/IEC14443B reader/writer communication scheme, provided that standardized
protocols, e.g. ISO/IEC 14443-4 and/or ISO/IEC 14443B anticollision are
correctly implemented.
Features
-
Supports ISO/IEC 14443A/M1 reader/writer mode
-
Supports ISO/IEC 14443B reader/writer mode
-
ISO/IEC14443A 106kbit/s and higher transfer speed at 212kbit/s and 424kbit/s
-
Typical operating distance in reader/writer mode for communication to an ISO/IEC 14443A card up to 50mm (depending on the antenna size and tuning
-
Supports host interfaces
♦ SPI interface up to 10Mbit/s
♦ 12C interface up to 400kbit/s in Fast Mode, and up to 3400kbit/s in High- Speed Mode
♦ Serial UART in different transfer speeds up to 1228.8kbit/s, framing according to the RS232 interface with voltage levels according to pad voltage supply -
Comfortable 64 bytes send and receive FIFO-buffer
-
Flexible interrupt modes
-
Multiple low-power modes
♦ Soft power-down mode
♦ Hard power-down mode
♦ Deep power-down mode(typical 1uA) -
Low Power external Card Detect (LPCD) at Reader/writer mode
-
Programmable timer
-
Internal oscillator to connect 27.12MHz quartz
-
Wide voltage supply: 2.2V ~ 3.6V
-
Dedicated transmitter voltage supply up to 5.5V
-
Integrated CRC Co-processor
-
Programmable I/O pins
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING
When using this product, basic precautions should always be followed, including the following:
- Read all the instructions before using the product.
- To reduce the risk of injury, close supervision is necessary when the product is used near children.
- DO NOT put fingers or hands into the product.
- DO NOT use this product if the flexible power cord or output cable is frayed, has broken insulation, or any other signs of damage.
- DO NOT allow anyone to ride the E-bike on his/her own unless he/she understands the proper operation and safety
warnings. Assist new riders until they are comfortable with the basic operation of the E-bike.
Meaning of Symbols and Marks
This product conforms to the applicable EC Directives.
WARNING- It is not permitted to dispose of this product as normal household
waste. Ensure that the product is recycled in accordance with local legal
requirements.
Federal Communications Commission (FCC) Compliance Statement for the USA
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including
interference that may cause undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement for Canada
This device complies with Industry Canada license-exempt RSS standard (s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
An Energy Technology Co.,Ltd is responsible for any changes or modifications not expressly approved by An Energy Technology Co.,Ltd. Such modifications could void the user’s authority to operate the equipment.
The risk solution and full text of the EU declaration of conformity
are available at the following internet address:
https://b2b.segway.com
Documents / Resources
| An
Energy Technology W015CN-01 Vehicle-Mounted 15W Wireless Charging
Seat
[pdf] User Manual
BV000001, 2AZX2-BV000001, 2AZX2BV000001, W015CN-10, W015CN-XX, W015CN-01
Vehicle-Mounted 15W Wireless Charging Seat, Vehicle-Mounted 15W Wireless
Charging Seat
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>