KENWOOD KMX75 kMix Table Mixer Instructions

KENWOOD KMX75 kMix Table Mixer

Specifications

• Model: TYPE KMX75, TYPE KMX76
• Material: Stainless steel (if supplied), Glass (if supplied)
• Compliance: EC Regulation 1935/2004 on materials and articles intended for food contact

Product Usage Instructions

1. Read and retain the instructions for future reference.
2. Remove all packaging and labels before use.
3. Check for any damage to the plug or cord before operation.

Small imperfections may be visible in the glass bowl, but it will not affect performance. Handle with care.

• Ensure the electricity supply matches specifications.
• Wash parts before first use following the ‘Care and Cleaning’ section.
• Lift the head release lever and lock the head in a raised position.
• Insert the required tool into the socket and lock it in place.
• Fit the bowl onto the base, aligning the handle with the lock symbol.
• Lower the mixer head and plug it into the power supply.
• Turn it on by adjusting the speed control.
• After use, unlock and remove the tool from the socket.
• If the mixer head is raised during operation, it will stop working immediately. Lower the head, reset the speed switch, and resume operation.
• The ‘mixer ready indicator light’ will go out when the head is raised and illuminate when lowered for use.
• Your mixer adjusts speed under different loads for consistent performance. Speed variation is normal during operation.
• Refer to the chart for guidance on using the K-beater attachment for various recipes like cakes, biscuits, pastries, etc.

FAQ

• Q: What should I do if the mixer stops during operation?
• A: Lower the head, reset the speed switch, and resume operation after a few seconds.

Safety

• Read these instructions carefully and retain for future reference.
• Remove all packaging and any labels.
• If the plug or cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorized Kenwood repairer to avoid a hazard.
• Switch off and unplug before fitting or removing tools/attachments, after use and before cleaning.
• Keep your fingers away from moving parts and fitted attachments.
• Never leave the machine on unattended.
• Never use a damaged machine. Get it checked or repaired: see ‘service and customer care’.
• Never let the cord hang down where a child could grab it.
• Never operate the Stand Mixer with the head in the raised position.
• Never let the power unit, cord or plug get wet.
• Never use an unauthorized attachment or both outlets at the same time
• Never exceed the maximum quantities and speeds stated in the Recommended Usage Chart.
• When using an attachment, read the safety instructions that come with it.
• Take care when removing bowl tools after extended use as they may get hot.
• Take care when lifting this appliance as it is heavy.
• Ensure the head is locked and that the bowl, tools, outlet cover, and cord are secure before lifting.
• When moving the appliance always pick up by the pedestal base and mixer head. Do not lift or carry the appliance by the bowl handle.
• Do not move or raise the mixer head with an attachment fitted as the Stand mixer could become unstable.
• Do not operate your appliance near the edge or overhanging the work surface or apply force to an attachment when fitted, as this may cause the unit to become unstable and tip over, which may result in injury.
• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
• Children should be supervised to ensure that they do not play with the appliance.
• Misuse of your appliance can result in injury.
• The short power-supply cord is used to reduce the risk resulting from becoming entangled in or tripping.
• Extension cords may be used if care is exercised in their use. If an extension cord is used: 1) The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and 2) The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally. 3) The extension cord should be an earthed-type 3-wire cord. The electrical rating of the appliance is listed on the bottom of the unit.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and if they understand the hazards involved.
• Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

Glass bowl

• Before using ensure that your bowl tools are adjusted to the correct height and not in contact with the bottom of the bowl – refer to the “tool adjustment” section.
• Do not allow the bowl to come in contact with sources of high heat such as an oven or stove top.
• Do not hit tools on the side of the bowl to remove ingredients.
• The glass bowl is microwave-safe.

Special Care Instructions

Glass is a natural material, during the manufacture of this bowl every care has been taken to ensure a perfect appearance, however, some small imperfections may be visible, this is normal and to be expected, the performance of the bowl will not be affected.

Before plugging in

• Make sure your electricity supply is the same as the one shown on the underside of your appliance.

Important – Plug and Fuse Information

• The wires in the cord are colored as follows:
  • Green and Yellow = Earth,
  • Blue = Neutral
  • Brown = Live
• If the plug supplied with your appliance has a fuse fitted and the fuse fails it must be replaced with one of the same rating.
• If the plug or cord requires replacing a new cord set should be fitted by an Authorised Kenwood Repairer.

WARNING: THIS APPLIANCE MUST BE EARTHED.
Note

• For non-rewireable plugs, the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained.
• The correct fuse cover is identified by color and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).
• If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a socket outlet.
• This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to come into contact with food.

Before Using For The First Time

• Wash the parts: see ‘Care and
• Cleaning section.

Key

1. Mixer’s head
2. Attachment outlet
3. Outlet cover
4. Tool socket
5. Bowl
   • a Stainless steel (if supplied)
   • b Glass (if supplied)
6. On/Off and speed control
7. Mixer-ready indicator light
8. Mixer body
9. Head release lever
10. Cord storage
11. K-beater
12. Whisk
13. Dough tool
14. Creaming beater (if supplied)
15. Folding tool (if supplied)
16. Spatula
17. Splashguard

FEATURES

To Use Your Mixer

1. Lift the head release lever(9) at the back of the Stand mixer(1) and at the same time lift the head(1) until it locks in the raised position (2).
2. Place the required tool into the socket. Then push up (3) and turn (4) the tool to lock into position.
3. Fit the bowl onto the base. Place the handle directly over the unlock symbol, then gently turn the bowl clockwise until the handle is directly above the lock symbol . DO NOT USE excessive force and DO NOT overtighten (5).
4. Lift the head release lever (9) at the back of the Stand mixer and at the same time lower the mixer head (1).
5. Plug into the power supply and the ‘mixer ready indicator light’ will illuminate.
6. Switch on by turning the speed control to the desired setting.
7. Release the tool by turning clockwise to unlock it from the tool socket and then remove it.

Important

• If the mixer head is raised during operation, the machine will stop working straight away. To re-start the mixer, lower the mixer head, turn the speed switch to the ‘O’ position, wait a few seconds and then re-select the speed. The mixer should resume operating straight away.
• Whenever the mixer head is raised the ‘mixer ready indicator light’ will go out. When the head is lowered, the light will illuminate indicating the mixer is ready to use.

Hints

• The fold function can be used for folding light ingredients into heavier mixtures for example meringues, mousses, fruit fools, Genoese sponges and soufflés, and to slowly incorporate flour and fruit into cake mixtures. The mixer will operate at a constant slow speed.
• Your Stand mixer has been fitted with a ‘soft start’ feature to minimize spillage. However, if the machine is switched on with a heavy mixture in the bowl such as bread dough, you may notice that the mixer takes a few seconds to reach the selected speed.

Electronic Speed Sensor Control

Your mixer is fitted with an electronic speed sensor control that is designed to maintain the speed under different load conditions, such as when kneading bread dough or when eggs are added to a cake mix. You may therefore hear some variation in speed during the operation as the mixer adjusts to the load and speed selected – this is normal.

Recommended Usage Chart

Eggs sizes used = medium-sized (Weight 53 – 63g)

• Eggs sizes used = medium-sized (Weight 53 – 63g)
• Whipping cream used = Fresh Whipping cream with a minimum 38% Fat content

• Eggs sizes used = medium-sized (Weight 53 – 63g)

• Eggs sizes used = medium-sized (Weight 53 – 63g)

1. Raise the mixer head until it locks.
2. Fit the bowl onto the base.
3. Push the splashguard onto the underside of the mixer head(6) until fully located. The hinged section should be positioned as shown.
4. Insert the required tool.
5. Lower the mixer head.
   • During mixing, ingredients can be added directly to the bowl via the hinged section of the splashguard(7).
   • You do not need to remove the splashguard to change tools.
6. Remove the splashguard by raising the mixer head and sliding it down.

Tool Adjustment

K-beater, Whisk, Creaming beater, and folding tool

The tools are set to the correct height for the bowl supplied in the factory and should not require adjustment.
However, if you wish to adjust the tool use a suitable 15mm spanner:
Then follow the instructions below:

1. Unplug the machine.

2. Raise the mixer head and insert the whisk or beater.

3. Lower the mixer head. If the clearance needs to be adjusted, raise the mixer head and remove the tool. Ideally, the whisk, K-beater, and folding tool should be almost touching the bottom of the bowl(8).
   Creaming beater

   • Ideally, it should be in contact with the bowl surface so that it gently wipes the bowl during mixing(13).

4. Using a suitable spanner loosen the nut sufficiently to allow adjustment of the shaft (9) or (14). To lower the tool closer to the bottom of the bowl, turn the shaft anti-clockwise.
   To raise the tool away from the bottom of the bowl turn the shaft clockwise.

5. Re-tighten the nut.

6. Fit the tool to the mixer and lower the mixer head. (Check its position see points above).

7. Repeat the above steps as necessary until the tool is set correctly. Once this is achieved tighten the nut securely.

Note: The spanner shown is for illustration purposes only.

Dough Tool
This tool is set at the factory and should require no adjustment.

Creaming Beater

• The creaming beater is designed for creaming and mixing soft ingredients.
• Do not use heavy recipes such as dough or hard ingredients, for example, those containing fruit stones, bones or shells.

Fitting the Wiper Blade
The wiper blade is supplied already fitted and should always be removed for cleaning(15).

1. Carefully fit the flexible wiper blade onto the tool by locating the base of the wiper blade into the slot(10) then fit one side into the groove before gently hooking the end in place(11). Repeat with the other side(12).

Care and Cleaning

• Always switch off and unplug before cleaning.

The power unit and outlet cover

• Wipe with a damp cloth, then dry.
• Never use abrasives or immerse in water.
• Store excess cord in the cord storage compartment(10) at the back of the machine.

Stainless steel bowl

• Wash by hand, then dry thoroughly or wash in the dishwasher.
• Never use a wire brush, steel wool or bleach to clean your stainless steel bowl. Use vinegar to remove limescale.
• Keep away from heat (cooker tops, ovens, microwaves).

Tools and splashguard

• Wash by hand, then dry thoroughly or wash in the dishwasher.

Creaming beater

• Always remove the flexible wiper blade from the tool before cleaning.
• Wash the flexible wiper blade and tool in hot soapy water, then dry thoroughly. Alternatively, the parts can be washed in a dishwasher.

Note: Please inspect the condition of the tool body before and after use and also regularly inspect the condition of the wiper blade and replace it if there are any signs of wear.

Glass bowl

• Wash the bowl in hot soapy water, then dry thoroughly.
• Alternatively, the bowl is dishwasher-safe.
• Note: The collar on the base of the bowl is removable and can be washed in the same way. To remove the collar, upturn the empty bowl and unscrew the collar in an anticlockwise direction.

Service and Customer Care

• If you experience any problems with the operation of the appliance, before calling for assistance refer to the ‘Troubleshooting Guide’ or visit www.kenwoodworld.com.

UK

• If you need help with:
• using your appliance or
• servicing, spare parts, or repairs (in or out of guarantee)
• call Kenwood customer care on 0345 222 0458. Have your model number
• (e.g. TYPE KMX75 or TYPE KMX76) and date code (5-digit code e.g. 21T04) ready.
• They are on the underside of the Stand Mixer.
• Spares and Attachments
• call 0844 557 3653

Other countries

• If you experience any problems with the operation of your appliance, before requesting assistance refer to the ‘Troubleshooting Guide’ section in the manual or visit www.kenwoodworld.com.
• Please note that your product is covered by a warranty, which complies with all legal provisions concerning any existing warranty and consumer rights in the country where the product was purchased.
• If your Kenwood product malfunctions or you find any defects, please send it or bring it to an authorized KENWOOD Service Centre. To find up-to-date details of your nearest authorised KENWOOD Service centre visit www.kenwoodworld.com or the website specific to your Country.
• Designed and engineered by Kenwood in the UK.
• Made in China.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT UNDER THE EUROPEAN DIRECTIVE ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection center or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources.
As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

Guarantee UK only

• If your Stand Mixer goes wrong within one year from the date you bought it, we will repair it (or replace it if necessary) free of charge provided:
  • you have not misused, neglected, or damaged it;
  • it has not been modified;
  • it is not secondhand;
  • it has not been used commercially;
  • you have not fitted a plug incorrectly; and
  • you supply your receipt to show when you bought it.
• This guarantee does not affect your statutory rights.

Troubleshooting

CONTACT

Kenwood Ltd

• New Lane
• Havant
• Hampshire
• PO9 2NH
• kenwoodworld.com.

© Copyright 2021 Kenwood Limited. All rights reserved

References

• Kenwood UK | Kenwood Home page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>