Yale Smart Safe Instruction Manual

Yale Smart Safe Instruction Manual

Yale Smart Safe Installation Instructions

Pour la version francaise voir US.YaleHome.com/Support

1. Download the Yale Access App
   Create an account
   
   Tip: If you already use the August App, use the same username and password.

2. **Unlock Safe Using Key

Open door and leave open until setup is complete.
Tip: When key is used to unlock, it must be used to lock.**

3. Insert Batteries

Open the battery compartment and insert 4 AA batteries. Reinstall the cover.

4. Add Safe to the Yale Access App
   Set up Smart Safe
   Tap “Set up a device” from the app menu. When asked, scan the Yale QR code on the inside of your safe door.
   Tip: Once batteries are inserted, you have 10 minutes to complete this step. If your app doesn’t find the safe, press and hold (5 secs) the reset button on the inside of the safe door.

5. Create Entry Codes
   
   Once added to the Yale Access App, you can create and delete entry codes or share app access by tapping the Guest icon in the bottom menu.

Connect WiFi Bridge                            Mounting Hardware
(Included with Select Models)

Key                    Rubber Feet                    AA Batteries (Alkaline only)

Needed for Optional Installation

Set up Connect*

Note serial number located on back of Connect. Plug Connect into an INDOOR outlet within 10 feet of the Smart Safe.
Tip: For best connectivity, make sure that the Connect bridge is in the line of sight of the front of the safe.
*Connect WiFi Bridge included with select models

Mount Safe For Added Security (Optional)

There are 8 mounting hole locations on the Smart Safe. Use included mounting template for guidance to secure the safe to the wall, shelf or floor.

Tips:

• Use Phillips #2 screwdriver to tighten screws.
• To avoid scratching or damaging your floor, attach the included 4 rubber feet to the bottom of the safe with the 3M side against safe.
  

Using Your Smart Safe

Outside

Safe can always be opened with the key or with a 9V battery and valid code.

Locking Safe

Close Safe Door Press any key to lock safe.

Settings Definitions

Privacy Mode

|

Off

| While in Privacy Mode, the safe will not open even when a valid Entry Code is entered. This setting can be changed from the Yale Access App.
Inside Light| On This feature cannot be turned off.|

The inside light will automatically turn on and stay on for 10 seconds when the safe door is opened.

One Touch Locking|

On This setting cannot be turned off.

| Touching any key on keypad will lock the safe.
Sound| On| The sound setting for entry code verification can be set from the Yale Access App.

Inside

• When safe is paired to app, Factory Reset must be done from app. During a factory reset the safe will be unlocked

Unlocking Safe

Warning: Changes or modifications to this device not expressly approved by
Yale Home could void the user’s authority to operate the equipment.

FCC ID: 2ABFG-IESD100PG0

FCC

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications (including the antennas) to
this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.

IC ID: 11626A-IESD100PG0 ISED

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

FCC and IC RF Radiation Exposure Statement:

This equipment complies with FCC and IC RF Radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>