Schneider Electric SMT10020 PowerLogic HeatTag Detect Abnomal Heating of Cables Instruction Manual

Schneider Electric SMT10020 PowerLogic HeatTag Detect Abnomal Heating of

Cables

Retain instruction sheet for future use. Visit our website at www.se.com to download the documents listed above (user guides U G ) and other documents.

PLEASE NOTE

• Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
• The HeatTag devices must be installed inside electrical panels or switchboards, behind a door or plate, so that they are inaccessible to unauthorised persons.
• All pertinent state, regional, and local safety regulations must be observed when installing and using this product.
• No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.

DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462, NOM 029-STPS or local equivalent.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Turn off all power supplying this equipment before working on or inside equipment.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors, and covers before turning on power to this equipment.

Failure to follow these instructions will result in death or serious injury.

Description

HeatTag

HeatTag devices detect abnormal heating of cables.

1. Operation LED
2. Network status LED Operation button
3. QR code to access device information
4. DIN clip
5. Air inlet
6. Power supply connector

Network Status LED

HeatTag switched off.| HeatTag in test mode.| HeatTag in normal

operation.

| HeatTag has triggered an alert.

Look for the cause of the heat rise in the switchboard.

| Minor malfunction detected.

Maintenance of HeatTag required.

| Major malfunction detected.

Replacement of HeatTag required.

---|---|---|---|---|---
Description

Alternating current
Comply with all safety instructions associated with this symbol to avoid any potential risk of injury or death.
WEEE directive 2012/19/EU (Waste Electrical and Electronic Equipment).

Dimensions

Installation Recommendations

HAZARD OF NON-DETECTION OF FIRE

• Do not use HeatTag as a safety device. HeatTag does not replace the fire protection devices of the building.
• The detection and communication functions of HeatTag can be deteriorated depending on its installation and use in the equipment.
• Do not disable the other monitoring and safety devices of the equipment. Failure to follow these instructions can result in death, serious injury, or equipment damage.

HAZARD OF NON OPERATION

• Install HeatTag inside electrical panel or switchboard according to the following instructions.
• Install the covers on the equipment.
• Do not install HeatTag in a forced air ventilated enclosure. Failure to follow these instructions can result in the loss of detection and communication functions.

HeatTag + PrismaSeT P / PrismaSeT 4000

1. Recommended installation
2. Possible
3. Forbidden

Installation

Wiring

FIRE HAZARD

• The HeatTag must be associated with an easily accessible upstream protection (2 A) and circuit-breaker system, marked with callout in the schematic below.
• Wire the HeatTag with wires that can withstand temperatures of 75°C.
• To conform to the UL/CSA norms, wire the HeatTag with a gauge equal to or lower than 18 AWG. Failure to follow these instructions can result in death, serious injury, or equipment damage.

Dielectric Test

HAZARD OF DEVICE DAMAGE
Disconnect the power supply of HeatTag before running a dielectric test. Failure to follow these instructions can result in equipment damage.

Configuration

• Refer to the HeatTag user guide to configure the HeatTag (see page 1).
• Refer to the user guide of the concentrator to configure your system.
• Before proceeding with pairing, ensure that the concentrator has the latest available firmware version. Refer to the user guide of the concerned concentrator.

Use

• After powering on HeatTag: HeatTag is in test mode for 30 minutes
• After 30 minutes, HeatTag can send its first alert
• After 8 hours HeatTag has discovered its environment and is completely operational.

Technical Data

• Power supply: 110–277 Va +/-15%
• Frequency: 50–60 Hz
• Maximum consumption: 0.1 A
• Operating temperature: -15 °C to +70 °C (5 °F to 158 °F)
• Relative humidity: 5–95 %
• Altitude of use: 0–2000 m (0–6500 ft)
• Overvoltage category: III
• Protective class: Class 2 front face
• Pollution degree: 3
• Impact resistance index: IK06, except 6.8 J on the front face
• Protection degree per IEC 60529: Box IP20
• Radio communication:
• ISM band 2,4 GHz (2,4 GHz to 2,4835 GHz)
• Channels 11 to 26 (IEEE 802.15.4)
• Equivalent isotropic Radiated Power (EIRP): 0 dBm

EU Declaration of Conformity
Hereby, Schneider Electric Industries SAS, declares that the Wireless sensor for early detection of overheating cables HeatTag SMT10020 is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU. The EU BE20042401 declaration of conformity can be downloaded on www.se.com/docs.

• IEEE 802.15.4 operating frequency: 2405–2480 MHz.
• Maximum radio-frequency power transmitted: < 10 mW.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Industry Canada Statement
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

References

• Систэм Электрик (Systeme Electric) | Официальный сайт, ранее Schneider Electric

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>