DIGI WB-20 Smart Wifi Module User Manual

CONFIDENTIAL

WB-20 SMART WIFI MODULE

Operation Manual

Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

FCC RF Safety Caution statement:
To satisfy FCC RF exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this transmitter must not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The device has been evaluated to meet general RF exposure requirement.

1. General Layout

Bridge Mode

In this mode, module connects AP with WIFI and emission WIFI itself, the ETH port is LAN,PC and other device could connect module with Ethernet cable

2. Features

• Onboard A64 Quad-core ARM Cortex-A53 1.2GHz (Fanless)
• 1G DDR3L co-layout memory
• 8G co-layout eMMC NAND flash
• WIFI 2.4G/5G 802.11a/b/g/n/ac
• Bluetooth 4.2
• TF CARD
• OS: Android 6.0

3. Operating Conditions

• Power Source : DC5V/0.15A
• Operating Temperature : 0 ~ +50°C
• Operating Humidity : 15 ~ 85% RH
• Power Consumption : 0.75W

4. Connectors

• DC 5V input connector (Pin head)
• 1x RS-232C interface (Pin head)
• 2x USB2.0 interface (One is pin head, the other is Mirco-USB)
• 2x LAN interface (One is pin head, the other is RJ45)
• 1x TF card socket

5. Network Setup

5.1 Link with Wired Cable Only
Set as normal scale

1. Set SPEC135=xxx (xxx is the last 3 digits of Lan IP)
2. Set SPEC50=1 (usually act as server) SPEC50=0 (only for cloud)
3. Set Rezero+0416=LAN IP
4. Set Rezero+0418=LAN Subnet Mask
5. Set Rezero+0421=LAN Gateway if necessary
6. Make sure in Rezero+0457, WIFI switch= Inhibit

computer name
S0.2 AMS STATIC| SELECT ETHERNET TYPE| Please always use X key to set it as STATIC
S0.3 AMS 000000000000| ENTER ETHERNET DNS1| Reserved
S0.4 AMS 000000000000| ENTER ETHERNET DNS2| Reserved
S0.5 AMS INHIBIT| SELECT WIFI SWITCH| Use X key to set it to ALLOW

5.2 Link with Wireless Only
5.2.1 Method 1: Set on Scale side
Set Rezero+0457 as below

computer name
S0.2 AMS STATIC| SELECT ETHERNET TYPE| Please always use X key to set it as STATIC
S0.3 AMS 000000000000| ENTER ETHERNET DNS1| Reserved
S0.4 AMS 000000000000| ENTER ETHERNET DNS2| Reserved
S0.5 AMS ALLOW| SELECT WIFI SWITCH| Use X key to set it to ALLOW
S0.6 AMS SSID 0| | Input SSID (Special symbol can be set by ASCII) P32 key to switch between local or ASCII
S0.7 AMS NO| SELECT WIFI ENCRYPTION| NO/WEP/WPA-PSK
S0.8 CH-01 PWD 0| | Enter password of WIFI
S0.9 AMS STATIC| SELECT WIFI TYPE| Please always use X key to set it as STATIC
S0.10 AMS 000000000000| ENTER WIFI IP1| Set WIFI IP address
S0.11 AMS 000000000000| ENTER WIFI SUBNET MASK1| Set WIFI subnet mask
S0.12 AMS 000000000000| ENTER WIFI DNS1| Set DNS if needed
S0.13 AMS 000000000000| ENTER WIFI IP2| Set only if customer use dual network segment
S0.14 AMS 000000000000| ENTER WIFI SUBNET MASK2
S0.15 AMS 000000000000| ENTER WIFI DNS2
S0.16 AMS 000000000000| ENTER WIFI GATEWAY| Set WIFI gateway
S0.17 AMS ALLOW| SELECT AM FTP SWITCH| Please always use X key to set it as Allow
S0.18 AMS 3000| SELECT AM FTP PORT| Port available : 3000-4000 except for 3721
S0.19 AMS USER 5| admin| Set FTP account
S0.20 AMS PWD 5| admin| Set FTP password
S0.21 AMS INHIBIT| SELECT SM101 P SWITCH| Select whether support to accept SM-101 protocol

5.2.2 Method 2: Send by AMS file

AMS file is the Android Module Setting file which contains the WIFI setting of scale.

A. Pull back AMS file
Below is a sample to pull back the AMS file from scale, then you got the template to modify to yours.

binary commend is very important here and can’t be omitted

(Rezero+0416)
admin| Enter FTP account
admin (hidden here)| Enter FTP password
lcd c:| Set local path for transfer data
binary| Use binary to transfer data (Important and necessary)
get ams0uall.csv| Pull back AMS file
by| End the session

B. Modify AMS file
Use Notepad++ to open the csv file to edit

Below is the data content:

1,,“SM- 120T”,1,010010092050,255255255000,192168001001,008008008008,004004004004,1,“TESTTESTTEST”,2,“11111111″,1,192168063050,255255255000,000000000000,000000000000,192168063001,192168063001,000000000000,1,3872,“admin”,“admin”,1

Below is the column definition