AVIAN-X AVXDP101 Powerflight Mallard User Manual

AVIAN-X AVXDP101 Powerflight Mallard

DECOY ASSEMBLY

1. Face the decoy with the head point away from you and the top of the decoy facing up.
2. Take the wing with the “L” on the shaft. Line up the pin on the decoy shaft with the pin in the wing shaft on the left side of the decoy.
3. Push wing onto decoy shaft
4. Take the wing with the “R” on the shaft. Line up the pin on the decoy shaft with the pin in the wing shaft on the right side of the decoy.
5. Push wing onto decoy shaft.

BATTERY INSTALLATION

1. With the decoy head facing away and the top of the decoy facing up grasp the feathers of the tail.
2. Gently pull up about an inch and then back to release the tail.
3. Move tail to the side of the decoy.
4. Hold battery on the side with the charging port and cord. Make sure post on battery is facing up.
5. Slide battery into housing with cord out and rotate lever down to hold battery in place.
6. Plug battery pack in (for lead acid battery connect red lead to positive and blue lead to negative).
7. Take tail and slide the rubber “T” into the slot in the decoy body while pushing down on the back of the tail.

BATTERY REMOVAL

1. With the decoy head facing away and the top of the decoy facing up grasp the feathers of the tail.
2. Gently pull up about an inch and then back to release the tail.
3. Move tail to the side of the decoy.
4. Disconnect battery (for lead acid battery remove the red and blue leads from the battery).
5. Rotate lever to the up position and pull battery out
6. Take tail and slide the rubber “T” into the slot in the decoy body while pushing down on the back of the tail.

STAKE ASSEMBLY

1. Stake can be used with 2 or 3 sections depending on how high off the ground you want the decoy.
2. To assemble the stake follow the diagram.
3. To mount to the decoy, take the square end and push square post of decoy into the stake.

DECOY OPERATION

1. To power on the decoy, use the switch on the bottom of the decoy. The switch is printed with “- “which means REMOTE, “O” which means OFF, and “=” which means SPIN.

REMOTE OPERATION

1. Turn switch to “REMOTE” position on the decoy.
2. For “SPIN” motion press the button that is printed with “SPIN”.
3. For “INTERMITTENT” motion press the middle button that is printed with “INTERMITTENT”.
4. To turn motion “OFF” press the bottom button that is printed with “OFF”.

REMOTE BATTERY REPLACEMENT & PAIRING

Remote Battery Replacement

1. Turn the remote so the back is facing up.
2. Remove the two screws holding the battery cap on.
3. Lift Battery cap off to expose the battery.
4. Replace battery with new CR2032 (Positive/+ side up).

Remote Pairing: these instructions can be used to pair a replacement remote to current decoy or to pair multiple decoys to one remote.

1. Turn on Decoy (with battery in decoy) and turn switch to “REMOTE”.
2. Press and hold “SPIN” button on remote for more than 4 seconds and release.
3. The LED inside decoy will be flashing.
4. Press the “SPIN” button once and release.
5. The LED inside the decoy will stop flashing when it is paired.

CHARGING BATTERY

Charging Battery Inside Decoy

1. Tip decoy upside down.
2. Locate charging port at the rear of the tail.
3. Insert charger cord and plug charger in.
4. Light on battery will be RED when charging and GREEN when Charged.
5. When complete remove charging cord.

Charging Separate Battery

1. To charge a decoy battery locate the charging port on the side of the battery.
2. Open the charging port by pulling the plug out.
3. Insert charger cord and plug charger in.
4. Light on battery will be RED when charging and GREEN when Charged.
5. When complete remove cord and insert plug.

STORAGE & TRANSPORTATION

1. When storing the decoy, the wings should be removed and stored flat and in a safe place to avoid damage.
2. The battery should also be removed and stored in a cool dry location.
3. For transporting the decoy, the wings should be removed to avoid damage to the wings.

PARTS LIST

• Tail Bungee
• Feet (set)
• Charger
• Remote
• Stake
• Wings (set)
• Tail
• Battery

WARRANTY

DISCLAIMERS
Avian-Xis not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of Avian-X products.

WARRANTY
For the warranty to be in effect, register your product at avian-x.com /warranty-registration. Follow the onscreen directions to complete the process.

Avian-X will replace all workmanship defects free of charge for ONE (1) YEAR after the date of purchase as long as your warranty is in effect. This warranty DOES NOT COVER damage, expense or injury caused by unauthorized repairs, alterations, improper connection, shipping, abuse, theft, accident, neglect or collateral loss.

CUSTOMER SERVICE
Avian-X stands behind every product we manufacture for a one-year product workmanship warranty and a strong commitment to customer service. If you are in need of customer service for missing parts or need assistance with the operation or assembly of your product, we encourage you to call one of our customer service representatives and let us assist you.
877-534-2263

DISCLAIMER
Avian-X reserves the right to make changes to product features, functionality and physical design at its sole discretion. As a result, such changes may not be reflected in this version of the manual.

FCC & IC

FCC STATEMENT
Product Name: Powerflight Mallard
Trade Name: Avian-X
Model#:AVXDP101 (Main Unit)
Model#: AVXDPRC01 (Remote)

FCC ID: YTTAVXDPl 01
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED COMPLIANCE STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subjectto the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>