Radar Detector Genevo One S User Manual
- June 6, 2024
- GENEVO
Table of Contents
USER MANUAL
Radar Detector Genevo One S
Congratulations on your purchase of the world´s most intelligent radar and laser detector Genevo One S.
Main functions of Genevo One S
Genevo One S is the most powerful detector from Genevo family and is designed to protect the driver from speeding fines. Genevo One S communicates with drivers in the English language and its main functions are the detection of microwave radars (X / K / Ka bands), laser guns, red-light cameras, and sectional speed cameras (using its own GPS database).
Notifications:
Text warning and voice alert appear on Genevo One S during radar alert. The
strength of the signal and beeps expresses the intensity of the received
signal. Signal strength has ten levels. GPS alerts are reported by voice. For
example “Speed Camera”.
Control:
-
Left button MENU / ON-OFF
Short press: You will enter into the setup menu. During the signaling radar, you will mute the volume. The next alarm will be reported again in the standard volume. Long press: Turn ON / OFF Genevo One S.
Radar Detector Genevo One S 1 -
Middle button BRIGHTNESS / ALERT SUPPRESSION
Short press: You can change the brightness of the display – Bright -> Dim -> Smart Dark -> Full Dark. Long Press: If you hold it during an alert you will mark the place of false radar reporting so at a given point detector during the next passage will be suppressed. If you suppress a false alert, the detector will not detect radars in a radius of about 150 meters. Hold button during the “suppressed” radar alert and this listing will be canceled. After the next passage radar alert will be signaled acoustically. -
Right button SENSITIVITY / ADD YOUR OWN GPS POINT
Short press: You can scroll between Highway / City / Auto City modes. In City or Auto City modes, the sensitivity of X / K / Ka bands can be reduced according to user preference. Long Press: Add your own GPS point. -
Buttons on the right side + /
Short press: Changing volume of the detector.
Menu:
Press the left button for entering into the menu. Press the left button to go
from one category to the next. Press VOLUME + or (on the right side of the
detector) to change your setting within a category. To complete this change,
simply wait a few seconds without pressing a button. The unit will display
“Setting Completed” to confirm your selection. Alternatively, you can get out
of the menu by pressing the right button.
Radar Detector Genevo One S 2
Items in the menu are as follows:
(recommended settings are highlighted)
Sensitivity: Highway / City / Auto City Setting the speed in Auto City (item
is present only if the sensitivity is set to Auto City): Through the Middle
button, you are selecting between speeds for editing (left number indicates
the speed below which the detector will not respond to alerts. Right number
indicates the speed below which the detector will detect alerts like in City
mode). + / – buttons on the right side of the detector change the specific
speed. When the detector is set up to “20 50” speed below 20 km/h the radar
will not respond. In the velocity range, 20-50 km/h will only respond to
stronger radar signals. Maximum detector sensitivity on the radar starts from
50 km/h.
Setting values City and Auto City sensitivity (entry is present only if the detector sensitivity is set to other than Highway): Via the Middle button you can select radar band for editing. To change the signal level which will respond to radar signals use + / -. The level of suppression can be selected in the range 0-9. For example, when setting is X2 K2 and Ka2 the level of detection in all bands are slightly decreased.
Display Mode: Speed/Time, Speed/Voltage, Battery Voltage, Time, Speed,
Speed/Compass
Auto Mute: On / Off: If it´s activated, after two seconds of ongoing alert the
volume will be reduced.
The minimum speed for signaling radar: Off, 10 km/h, 20 km/h, 30km/h ……… ..
130 km/h
X-Band: On / Off
K-Band: Wide / Narrow / Instant Only / Off (In countries, where police use K
band radars, it is recommended to use K Narrow setting)
Ka-Band: Wide / Narrow / Off
Ka Filter: Off / Normal / High – Filtering false alerts from blind spots and
ACC. (When Ka Filter is activated, detection distance on Ka-band radars is
slightly reduced. We recommend using „Normal“ which is a very good
insensitivity/false alerts immunity ratio.)
Laser: On / Off
Startup sound: On / Off
GPS connect announce: On / Off
GPS detection by database type: Via you can select the type of GPS points. For
editing use + / -. You can turn on and Middle button off a particular type of
point.
GPS warning distance: Normal (approx. 250m) / Farther (approx. 375m) / Farest
(approx. 500m)
Setting local time: You can change time zone via + / –
Language: English / Deutsch / Czech
Factory reset: For reset press middle button.
Delete all user points: For deleting all user points press middle button.
SpeedMeter Option:
This function is intended for the legalization of the detector when used in countries where radar detectors are prohibited. The detector stops alerting you on GPS points, radars, and lasers and there is only your current speed shown on the display. To activate this function you need to hold the middle button and right button together for approximately 5 seconds. After that, you will enter into SpeedMeter mode. To reactivate your detector again, unplug it from the power source, hold the right button and “+” button and then plug it into the power source. You need to hold the buttons for approximately 8 seconds. After 8 seconds display will show (SpeedMeter OFF). Now you have a fully working detector again.
Operating frequency:
GPS:
Ka narrow:
Ka wide:
K narrow:
K wide:
X band:
Laser:| SiRF STAR IV
34,0GHz, 34,3GHz, 34.7GHz, 35,5GHz (±120MHz)
33.4 GHz ~ 36.0 GHz
24.125GHz (±70MHz)
24.125GHz (±150MHz)
10.525GHz (±50MHz)
904nm
---|---
Technical parameters:
Operating temperature:
Storage temperature:
Operating voltage:
Energy consumption:
Dimensions:| -20 +85 °C
-20 +85 °C
11 – 16 V
250mA normal, 330mA max. (12V)
62 92 34 mm
---|---
Database Updates:
The database update is recommended to check once in three months. Downloading
the new database is performed according to the instructions
www.genevo.com/en/updates
while at www.genevo.com/en/updates-subscription you can register and receive notifications of new and
updated database to your email.
CE – Declaration of conformity
You can find the Declaration of Conformity in its entirety at: www.genevo.com/en/ce-one-en.pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>