Chug QIC42 Magsafe Pad User Manual
- June 6, 2024
- Chug
Table of Contents
Chug QIC42 Magsafe Pad
View
quick tips
- The device should stick firmly to the pad when charging
- Thick phone cases as well as some materials can interfere with MagSafe® charging
- This is a high speed magnetic charging pad, make the most of the charger by using the Power Delivery wall plug that was packaged with it; using a different power source may charge your device at a slower speed
included
- Magnetic charging pad with attached charging cable
- Power Delivery wall plug
charging
- Place the magnetic charging pad on a sturdy flat surface
- Connect the Power Delivery wall plug to the wall outlet using the attached USB-C cable (recommended)
- If you need to use a different power source make sure it is a USB power supply of
- DC 9V 2.22A minimum warning: please use UL compliant power supply
- Place your MagSafe® compatible device onto the magnetic charging pad; the device will stick to the pad and the screen will indicate that it is charging
- Remove credit cards or any card with a magnetic strip to prevent damage to the cards before charging
- Charge time will vary by device
troubleshooting
- If you’re having issues charging use the tips below to help:
- Double check that the USB-C cable and Power Delivery wall plug are plugged in
- Certain phone cases may interfere with MagSafe® charging; remove the phone case for best results
- Double check the placement of the device on the magnetic charging pad; for best results, the center of the device should be on the center of the magnetic charging pad
- MagSafe® charging is compatible with iPhone® 12 and newer as well as other Qi-enabled devices; please consult your devices user manual if you are unsure if your device is compatible
need some help?
Can’t get it to charge? Just have a question?
- call us at: 877-698-4883 or: 877-MyTgtTech
- e-mail us at: TargetTechSupport.com
safety
- Remove credit cards and other cards with magnetic strips to prevent damage to the cards
- Keep the charger away from heat and direct sunlight
- Do not modify or repair this device
- Do not use in high temperatures or extreme weather
- Do not use chemical detergents to clean your device, use a soft dry cloth
- Immediately unplug it from its power source if it gets wet
- Remove the protective film on the Power Delivery wall plug before using
FCC Statment
FCC ID: 2AO23-QIC42 Model: QIC42 Input: DC 9V/2.22A Output: MagSafe Charger
15W Made in Vietnam
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation. Warning: Changes or
modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Target Corp. Mpls. MN, 55403 Phone:
612-304-6073
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>