Chug ANC1 active noise-canceling headphones User Manual

June 5, 2024
Chug

Chug ANC1 active noise-canceling headphones

OVERVIEW

Chug-ANC1-active-noise-canceling-headphones-
FIG-1

included

  •  Bluetooth Wireless ANC Headphones
  •  USB-C Charging Coble
  •  3.5mm Audio Coble
  •  Carrying Cose

indicators

  • Quick Flashing White – Poi ring
  • Single Flashing White-Paired
  •  Short Double Flashing White – Re-pairing
  •  Rapid Flashing White – Incoming coll
  •  Intermittent Flashing White – Active coll/streaming
  • Solid Red – Low power/charging
  • Red Light Off – Charging complete
  •  Ascending Tones – Power on
  •  Descending Tones – Power off
  •  Three Rapid Tones – Ready to pair
  •  Two Rapid Dings – Low battery
  •  Quick Ascending Tone – Mox volume
  •  Quick Descending Tone – Min. volume

pairing

  •  When headphones ore off, press and continuously hold the power button for 7 seconds until indicator flashes white on the right side
  •  Use the Bluetooth settings on your phone to pair with HEYDAY HEADPHONES 02
  •  Slow single flashing white light – pairing successful
    Note: Hold power button for 4 seconds to power on and off

ANC/AMB button indicators

  •  ANG/Ambient Solid White – ANG/Ambient on
  •  Two Ascending Tones – ANC ON
  •  Two High Tones – Ambient ON
  •  Two Descending Tones – ANC OFF

ANC (Active Noise-Canceling)/AMB (Ambient)

  •  Utilize the ANC button to cycle the three different active noise-cancellation settings

  •  Pressing the button once from off will enter ANC mode (Active Noise-Cancellation) and is indicated with two ascending tones

  •  ANC mode reduces outside noise and makes your music the focus of your trip instead of the people around you

  •  Pressing the button again (twice from off) will enter AMS mode (Ambient) and is indicated by two high tones

  •  AMS mode only lets in high-frequency sounds this way you con still get some quiet time on a bus or airplane but never miss an announcement

  •  Pressing the button again (three from off) will turn OFF the Active Noise-Cancellation and is indicated with two descending tones

  •  If the headphones are turned off when ANC or AMS is active, that mode will be activated when the headphones are turned back on
    note: AMS mode does not work with the aux cable plugged in charging

  •  Plug USS-C end of charger into headphones

  •  Plug USS end of charging coble into o power supply of ot least DC SV 300mA warning: please use UL compliant power supply

  •  Full charge requires approximately 3 – 3.5 hours

  •  Charging is complete when red light turns off
    note: headphones cannot playback when charging aux/line in

  •  Insert the AUX cable into headphone AUX port

  •  Insert opposite end of the AUX cable into the media source

troubleshooting

  •  If the headphones are not working correctly, turn them on/off to reset
  •  If the headphones won’t turn on, recharge the battery and try again
  • If the headphones won’t charge, make sure the power supply works, is SV 300mA, and not damaged
  •  If the headphones make no sound or do not show as on available device, make sure they ore not paired to o different device already
  •  To re-enter pairing mode hold the power button for 7 seconds

safety

  •  Do not use near any water source
  •  Do not modify or repair this device
  •  Do not use in high temperatures or extreme weather
  •  Do not use chemical detergents to clean your device, use a soft dry cloth

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Statment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals