Chug TWS04 Noise Canceling True Wireless Earbuds User Guide

June 6, 2024
Chug

TWS04 Noise Canceling True Wireless Earbuds
User GuideChug TWS04 Noise Canceling True Wireless
Earbuds

hey! Welcome to your Heyday™ one true wireless earbuds. let’s get you set up.

Earbuds

Chug TWS04 Noise Canceling True Wireless Earbuds - figure
1

included

  • TWSANC Earbuds
  • TWS ANC Earbud Cose
  • US8-C Charging Cable
  • Small, Medium, and Lorge Earbud Tips x 2 colors, total of 6 sets

indicators

  • Earbud Rapid Flashing Red and White – Pairing mode
  • Earbud Flashes White and Fades – Paired
  • Earbud Flashing Red -Low power
  • Eorbud Solid Red -Charging
  • Earbud No Light – Charging complete
  • Case One Light 25% charged
  • Case Two Lights – 50% charged
  • Case Three Lights -75% charged
  • Case Four Lights -100% charged
  • Ascending Tones – Power on
  • Descending Tones Power off
  • Three Rapid Tones – Ready to pair
  • Single Chime – Posted
  • Two Rapid Dings – Low battery Quick Beep – Next(R)/previous(L) song

ANC/AMB indicators

  • Two Ascending Tones – ANCON
  • Two High Tones – Ambient ON
  • Two Descending Tones ANC OFF

Parring

|
---|---
To pair the earbuds to your device for the first time open the case and remove both earbuds.| The buds will start to flash red and white, this means that they are ready to pair.
|
Use the Bluetooth settings on your device to pair with HEYDAY  EARBUD 07.When the earbuds have successfully paired you will hear a chime and the light will turn white for five seconds and then fade.| To reenter pairing put both earbuds back into the charging case. Leave the lid on the charging case open and hold the reset button on the back for 3 seconds; the earbuds will flash red and white. To reset to factory settings hold for 6 seconds; the case power indicator will flash and sequence. After reentering pairing or resetting start the pairing process at step 1.

Touch controls

a quick tip: the touch sensor is located in the center of the earbud, be sure to touch here so inputs register Chug TWS04 Noise Canceling True Wireless
Earbuds - figure 6

*indicates that the left and right earbud have a different function
**indicates that this only works when using a single earbud

earbud tips

|
---|---
The earbuds come with small, medium, and large earbud tips in two different shapes and can be changed at any time.| To change the size of the earbud tip, squeeze it and pull it away from the eorbud.
Select the size that is the most comfortable for you. Flip the earbud tip inside out so you can see the interior sleeve. Slide the interior sleeve onto the earbud. Repeat steps 2 and 3 for the second earbud. If you need to switch to another size follow all 3 steps.

ANC (Active Noise-Canceling)/AMB (Ambient)

  • Press the left earbud button twice after turning the earbuds on to enter ANC mode (Active Noise -Cancellation); this is indicated with two ascending tones
  • ANC mode reduces outside noise by at least 20dB so you can listen without distraction
  • Press the left eorbud button two more times while in ANC mode to enter AMB mode (Ambient); this is indicated by two high tones
  • AMB lets in high-frequency sound so you can still hear announcements
  • Pressing the left earbud two more times while in AMB mode will turn OFF Active
    Noise -Cancellation and is indicated with two descending tones

Charging earbuds

  • Place both earbuds back into the case
  • Charging is complete when lights turn off
  • Full charge requires approximately 1.5 hours

Charging case

  • Plug the USB-C end of the charger into the back of the case
  • Plug USB end into a power supply of at least DC 5V 1A warning: please use UL compliant power supply
  • Full charge requires approximately 2.5 hours and will provide 24 hours of earbud use
  • Charging is complete when all 4 LEDs are solid white

IPX4 water resistance

  • The earbuds are resistant to sweat which means they’re perfect for workouts note: the charging case does not have the same rating and should not be used in the same conditions

single eorbud use

After pairing to your device remove either earbud from the case to enter single earbud use
Note: ANC/AMB modes will not work when using a single earbud

pro ximity sensor

When you remove an earbud while they are in use, the media you are listening to will pause automatically and restart when the earbud is replaced

troubleshooting

  • If the earbuds are not working place them into the case with the lid open and reset them If the earbuds won’t turn on, recharge the battery and try again lf the earbuds  won’t charge, make sure the power supply works, is 5V>1A, not damaged and that the case is charged
  • If the earbuds still won’t charge, make sure the charge pins are clear of debris as this may cause a connection issue; if they are use a soft dry cloth to clean them
  • If the earbuds make no sound or do not show as on the available device, make sure they are not paired, if so unpair the device and repair it to the desired device

need some help?
Can’t get it to pair? Hove o question or comment?

| call us at: 877-698 -4883 or: 877-MyTgtTech
---|---
| online at: TargetTechSupport.com

safety

  • Do not use near any water source
  • Do not modify or repair this device
  • Do not use chemical detergents to clean your device, use a soft dry cloth
  • WARNING: The battery (battery or batteries or battery pock) shall not be exposed to excessive heat such as sunshine, fire, or the like

heyday™ ****

FCC ID: 2A023-TWO4 Model: TWO4 Input: 5V 1A Max
Earbud Battery Capacity: 3.7V/60mAh/0.222Wh Case Battery Capacity: 3.7V/ 420mAh/1.56Wh Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Target Corp. Mpls. MN, 55403 Phone:1-612-304-6073

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals