Chug QIC33 Wireless Charging Pad Instruction Manual
- June 5, 2024
- Chug
Table of Contents
QIC33 Wireless Charging Pad
Instruction Manual
quick tips
- Alignment matters – centering the device on the charging surface ensures the fastest and most efficient charge
- Thick phone cases, as well as some materials, can interfere with the ability to charge This is a high-speed wireless charger. Make the most of the charger by using the USB-C cable and Quick Charge 3.0 wall plug that was packaged with it. Using a different power source may charge your device at a slower speed
included
- Wireless charger
- USB-C charging cable
- Quick Charge 3.0 wall plug
indicators
- Solid Red – Charging your device
- Solid White – Fully charged
*Flashing Red – Foreign object detection, pieces of metal, or other materials may cause overheating and damage your charger or phone. Remove the immediately
charging
- Place the charger on a sturdy the surface
- Plug the USB-C cable into the wireless charger and quick charge the 3.0 wall plug, then plug the Quick Charge 3.0 wall plug into an outlet
- If you need to use a different power source make sure it is a USB power supply of DC 9V 2A minimum warning: please use UL compliant power supply
- Place your Qi-enabled device onto the wireless charger and align the device with the center of the charging surface or the device will not charge
- Remove credit cards or any card with a magnetic strip to prevent damage to the cards before charging
- Charge time will vary by device
troubleshooting
-
If you’re having issues charging use the tips below to help:
-
Double-check that the USB-C cable and Quick Charge 3.0 wall plug are plugged in
-
Certain phone cases may interfere with wireless charging. Remove the phone case for the best results
-
Double-check the placement of the device on the wireless charger. For best results, the center of the device should be on the center of the wireless charger
-
Wireless charging is compatible with iPhone 8 and newer as well as other Qi-enabled devices. Please consult your device’s user manual if you are unsure if your device is compatible
and need some help?
Can’t get it to charge? Just have a question?
|
---|---
call us at: 877-698-4883 or:
877-MyTgtTech| e-mail us at:
TargetTechSupport.com
safety
- Remove credit cards and other cards with magnetic strips to prevent damage to the cards
- Keep the charger away from heat and direct sunlight
- Do not modify or repair this device
- Do not use it in high temperatures or extreme weather
- Do not use chemical detergents to clean your device, use a soft dry cloth
- Immediately unplug it from its power source if it gets wet
- Remove the protective film on the Quick Charge 3.0 wall plug before using
heqdaq™
FCC ID: 2AO23-QIC33 Model: QIC33 Input: DC5V/2A 9V/2A 12V/1.67A Output: 15W
Max Made in Vietnam This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: 1) this device may not
cause harmful interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation. Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not nstalled and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Target Corp. Mpls. MN, 55403 Phone:
612-304-6073
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>