Tineco Floor One S5 Series Samrt Cordless Vacuum and Washer Instruction Manual

FLOOR ONE S5 COMBO SERIES ES Smart Cordless Vacuum & Washer

Instruction Manual

TINOCO IS HERE TO HELP
We’ll get back to you within 1 business day

http://www.tineco.com

www.tineco.com
1-855-292-8864
Mon. – Fri. 9am – 6pm (CST)

Important Safety Instructions

SAVE THESE INSTRUCTIONS
Household use only.
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

WARNING – To reduce the risk of fire, electric shock, or injury:

1. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision.

2. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.

3. Use only indoors, on non-carpeted floor surfaces such as vinyl, tile, sealed wood, etc. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.

4. Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.

5. Use only as described in this manual. Use only the manufacturer’s recommended attachments.

6. Do not use with a damaged cord or plug. If the appliance has been dropped, damaged, left outdoors, dropped into water, or is not working as it should return it to a service center.

7. Do not handle charger, including charger plug, and charger terminals with wet hands.

8. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

9. Keep hair, loose clothing, fingers, and all parts of your body away from openings and moving parts.

10. Use extra care when cleaning on stairs.

11. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

13. Do not use without a filter.

14. Prevent unintentional activation. Ensure the switch is in the off-position before picking up or carrying the appliance. Carrying the appliance with your finger on the switch  or energizing an appliance that have the switch on invites accidents.

15. Always switch off the appliance before making any adjustments, changing accessories, or storing the appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.

16. 16. Recharge only with the charger specified by Tinoco. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

17. Use appliances only with specifically designated Tineco battery packs. Use of any other battery packs may create a risk of injury and fire.

18. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid comes into eye contact, seek
    medical help. Liquid ejected from the battery may cause irritation or burns.

19. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk
    of injury.

20. Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 266°F (130°C) may cause an explosion.

21. Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or
    at temperatures outside of the specified range may damage the battery and increase the risk of fire.

22. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

23. This appliance contains battery cells that are non-replaceable. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.

24. Always turn off this appliance before connecting or disconnecting the motorized nozzle.

25.  Do not charge or store the appliance outdoors or inside the car. Only charge, sto e or use the battery in a dry indoor area where the temperature is higher than 39.2°F (4°C) but lower than 104°F (40°C). The charger is for indoor use only.

26. Do not use to pick up ultrafine particles, such as lime, cement, sawdust, gypsum powder, or ashes.

27. Do not use to pick up sharp objects, such as metallic nails, pieces of glass, metal paper clips, or pins.

28. Do not use to pick up hazardous material and chemicals, such as solvent, drain cleaner, strong acids, or strong alkali.

29. Stop using immediately if the appliance is overheating, making unusual noises, producing unusual odors, performing low suction, or leaks electricity.

30. Turn the cleaner OFF and disconnect from the electrical outlet for long-term storage.

31.  Always clean the Dirty Water Tank after each use to avoid potential blockage, which may lead to low suction power, motor overheating, or reduce the service life of the
    appliance.

32. Store appropriately indoors in a dry place after use.

33. Do not place or submerge appliances in standing water or try to clean flooded areas.

34. All data and technical instructions of this manual are based on results from lab tests of Tineco or designated third parties. The company reserves all rights for final
    explanations.

35. The plug must be removed from the socket outlet before cleaning or maintaining the appliance.

36. A hazard may occur if the appliance runs over the supply cord.

37. Do not use the appliance when the water depth is more than 5mm above the surface.

Range of Usage

1.  The cordless hard floor cleaner is to be used on indoor hard floors, such as vinyl, tile, sealed wood, etc. Use on a rough surface may not get the best performance.
2. Keep your appliance away from heat sources, such as fireplace or heater, to avoid casing deformation.
3. Do not use to pick up flammable or combustible liquids, ultrafine particles, sharp objects, hazardous material, chemicals or anything that is burning or smoking, as described above.

About Cleaning Solution

1.  A large amount of cleaning solution entering into the motor may cause damage to the appliance.

2. Add solution as instructed in the Operation section. We recommend using the provided cleaning solution. Do not use the product with acidic, alkaline solution, or any
   substances harmful to the environment.

3. Keep out of reach of children. If any solution gets into the eyes, immediately flush them with clean water. If any solution is swallowed by accident, seek medical care
   immediately.

4. Dirty water and solution disposal should comply with local environmental regulations.

About the Appliance

1.  Do not modify or attempt to repair the appliance except as indicated in the instructions for operating and cleaning.

2. Charge the appliance with the Tineco adaptor. Input Voltage: AC 100-240V. Both high and low voltages can damage the adaptor, appliance, or even cause danger to the user.

3. Use extra care when cleaning on stairs.

4. Ensure that the Power Switch is in the OFF position before picking up or carrying the appliance. Do not lay flat or lean the appliance so as to prevent dirty water from
   entering into the motor.

5. To avoid being tripped accidentally, please put away the appliance on the charging base.

6. Always install the Dirty Water Tank and Clean Water Tank properly before use.

7. Do not allow the appliance or charger to get wet to avoid the risk of fire or injury caused by a short circuit.

FCC Supplier’s Declaration of Conformity

TYCO / FLOOR ONE S5 COMBO SERIES
This appliance complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This appliance may not cause harmful interference, and (2) this appliance must accept any interference received, including interference that may cause undesired operation.
TINECO INTELLIGENT, INC.
1700 WESTLAKE AVENUE N., SUITE 200, SEATTLE, WA, 98109, USA
WWW.TINECO.COM
1-855-292-8864

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital appliance, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Note
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment, such modifications could void the user’s authority to operate this equipment.

IC Note
This appliance contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:

(1) This appliance may not cause interference.
(2) This appliance must accept any interference, including interference that may cause undesired operation of the appliance.
– This Class B digital apparatus complies with Canadian ICES-003.
– This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Overview

A. Self-cleaning Button
B. AUTO/MAX Mode
C. Power On/Off
D. Digital Display
E. Dirty Water Tank Release
F. Dirty Water Tank Handle
G. Dirty Water Tank (DWT)
H. Brush Roller Cover
I. Tube
J. WiFi/Mute Button| K. Clean Water Tank Release
L. Clean Water Tank Handle
M. Clean Water Tank (CWT)
N. Brush Roller
O. Deodorizing & Cleaning Solution
P. Cleaning Tool
Q. Dry Filter & Holder
R. Accessory Holder
S. Adaptor
T. Charging Base
---|---

Digital Display

A. WiFi Indicator
B. DWT Full or Blocked
C. Dirt Monitoring Loop
(Blue to red according to the dirt amount)
D. AUTO Mode
E. CWT Empty| F. Brush Roller Tangled Indicator
G. Power Indicator
H. Tineco Logo
I. Self-cleaning Icon
J. Battery Level Indicator
---|---

Accessories

Note: Accessories may vary between markets. If you require more accessories, please go to www.tineco.com or store.tineco.com.

Deodorizing & Cleaning Solution

Removes dirt, grime, grease, and tough stains from most types of hard surfaces, like tile, marble, sealed hardwood floors, and more. Always use the Tineco solution in your appliance.

Add one bottle cap of the solution to each full tank of clean water.

Brush Roller

A soft roller head with bristles can be used to vacuum and wash at the same time. It can be easily cleaned with the self-cleaning function.

Dry Filter

Dry filter and filter net can block large particles and debris, ensuring the appliance’s durability.

• Please install the dry filter before use, or it may lead to weak suction.

Cleaning Tool

A full brush to clean the DWT, brush chamber, and opening. The tool also has a bristled end to remove dirt and mud on the roller and DWT.

Assembly

How to Assemble/Disassemble

Note: For water tank and brush assembly, please refer to “Operation” and “Maintenance”.

To assemble, install the main body and handle into the appliance until you hear a click.

In the event that the handle needs to be disassembled, first, remove the main body. Press the spring to release the handle with a tool (like a screwdriver) and lift the released handle from the appliance.

**Operation

**

Preparing for Use
Before first use, please charge the appliance for 3~4 hours (refer to “Charging Instructions” for details).

• Based on results from Tineco lab tests. Lab temperature 39.2°F (4°C) ~ 104°F (40°C).

Press the button and the appliance will start in AUTO mode by default. Press it again to turn off the appliance. Switch between AUTO and MAX mode by pressing the  button.

The appliance will stop working when put uprightly and start running again when you recline. * Do not recline more than 142° to protect against water leakage.

Tips:

•  Solution mode/ Water Only mode:
  The appliance starts with Solution mode by default. Power on while the appliance is upright, long-press for 3s to switch between the two modes.

• Switch to Water Only mode:
  LED Loop: Red → Blue (use water only)

• Switch to Solution mode:
  LED Loop: Blue → Red (use cleaning solution)

Place the appliance on the charging base vertically after use for recharge and storage.

Note:

•  Selecting the appropriate mode depending on the CWT contents is vital for maximum dirt detection effectiveness.
• Do not vacuum foamed liquid.
• To vacuum water left on the surface, the appliance will switch off in 3 seconds after power off.

Filling Clean Water Tank

Press the Clean Water Tank release button to remove it from the appliance.

Place the tank back into the appliance. You should hear a “Click” if done correctly.

Charging Instructions

To charge the appliance, place the appliance on the charging base and plug the adaptor into a power outlet.

1. Connect the external charging cord to the charging base and plug it into the wall outlet.
2. To avoid tripping hazards, please place the appliance on the charging base near a wall during charging.
   
   

Open the tank cap, and fill it with tap water to the Max line. When deep cleaning is necessary, add one bottle cap of the solution to the CWT and tightly close the cap.

Note:
Only use water under 140°F/60°C.

DO NOT USE HOT WATER.

Warning:

•  Only charge the appliance with the adaptor supplied by Tinoco.
• During long periods of not being used, the appliance must be charged once every 3 months for optimal performance.
• Store indoors in a dry place. Do not expose the appliance to sunlight or freezing temperatures.
  Recommended temperature range: 39.2°F (4°C) ~ 104°F (40°C).

Cleaning Mode Selection

AUTO Mode

• In AUTO mode, the iLoop™ sensor automatically detects how dirty the floor is and applies the appropriate amount of detergent and suction power.
• A red dirt monitoring loop indicates more dirt is detected, and a blue loop indicates less dirt is detected. This mode automatically provides the best cleaning solution.

MAX Mode

• In AUTO mode, press the button to enter MAX mode.
• In Max mode, the appliance will apply max suction power and will spray water/solution for deeper cleaning.

Note:

• Clean the dustbin and filters after each use.

• To maintain high performance, wash and dry the sponge filter monthly, replacing it every 6 months.
  Wash and dry the HEPA filter every 3 months, replacing it every 12 months.

• Air dry completely before reinstalling.

Runtime

•  The runtime for the Floor Washer is about 15~20 minutes.
• The runtime for the Hand Vac is about 25~50 minutes.
• Estimated runtime data was obtained by a Tineco Laboratory.

Charging Time

• A full charge takes approximately 3~4 hours.
• Estimated data was obtained by a Tineco Laboratory using ambient temperatures between 39.2°F (4°C) to 104°F (40°C).

Indicator

When in Use

App
All the functions can be performed using the Tineco app. Download the Tineco app from the App Store, Google Play, and Tineco Official Site.

Note: The default setting for voice prompt in English, you can set other languages via App.
Voice Prompt (Contents may vary, please in kind prevail.)

cleaning solution
Need self-cleaning| Please begin the self-cleaning cycle
Appliance not on the charging base| Please place the appliance on the charging base
Dirty Water Tank is full| Dirty Water Tank full, please empty
Dirty Water Tank not installed| Please install the Dirty Water Tank
The brush roller is tangled| Please clean the brush roller.
Brush roller not installed| Please install the brush roller correctly
Power is off| Power off
Start charging| Charging has commenced
Begin self-cleaning cycle| Auto-detecting whether to run self-cleaning cycle, please begin the self-cleaning cycle
Battery insufficient for self-cleaning| Low battery, start charging
Sufficient battery to start self-cleaning| Start self-cleaning
Cleaning brush roller| Cleaning brush roller
Cleaning debris channel| Cleaning debris channel
Auto detecting| Auto detecting
Deep cleaning| Deep cleaning
Self-cleaning stopped| Self-cleaning cycle stopped, please clean Dirty Water Tank
Self-cleaning complete| Self-cleaning cycle complete, please clean Dirty Water Tank

Maintenance

Note:

• For optimal performance and to prevent odors, always clean and dry DWT, floater, filters, brush roller, brush roller cover completely after each use.
• Please make sure each part is installed correctly or the appliance may not work properly.
• After maintenance, place the appliance on the charging base vertically. Do not expose the appliance to direct sunlight, and store it indoors in a dry place.

Main Body

To reduce the risk of injury, switch off before performing maintenance.

When the indicator of Dust Sensor Malfunction blinking, remove Dirty Water Tank, clean the dirt sensor with a damp cloth or the cleaning tool.

Use a cloth to clean the surface with a neutral detergent. The cloth should be dry to prevent water from entering the appliance.

Dirty Water Tank

• When dirty water reaches the Max line, the appliance will stop working and show a reminder on the display and play a voice prompt.
• Pull up the tank lid to empty the DWT. Use the cleaning tool to remove the remaining debris. Rinse the inside of the DWT and place it back into the appliance.

Dirty Water Tank Lid

If the Dirty Water Tank lid and the filter inside have been blocked, remove the tank lid and the filter, rinse both parts with water.
Dry Filter

Grasp recessed area on each side of the dry filter and pull upward. Rinse under running water and must be completely dry before recombining with the lid of the DWT.

• A spare dry filter is provided with your appliance for convenient replacement.

Brush Roller Self-cleaning

1. Place the appliance on the charging base after use, the sensor will auto-detect the level of dirt.
2. When you hear the voice prompt “please begin the self-cleaning cycle,” press the self-cleaning button and begin the process.
3. Once complete, you will hear the voice prompt “self-cleaning completed, please clean the Dirty Water Tank.” At this point, the appliance will begin charging.

Note:

•  Ensure the charging base is plugged in.
• Before the self-cleaning cycle, please clean the DWT and ensure the water level in the CWT exceeds 40%.

Brush Roller Cover Squeeze latches on the cover and pulls upward to remove.
When replacing, always latch the brush cover into place to avoid leakage.

Rinse with water.

Brush Roller

Remove the brush roller by grabbing the brush roller tab and pulling it out.

Remove hair and debris from the brush roller chamber and the opening with a tissue or a damp cloth.

Using the cleaning tool, remove the hair and debris wrapped around the roller and rinse with water. Replace the brush roller back into the accessory holder, and allow it to dry completely before reinstalling.

Replace the brush roller by inserting the brush roller end into the right side of the holder, then attach the roller tab to the magnetic buckle on the left side to lock into place.

Note: A spare brush roller is provided with your appliance for convenient replacement.

Specifications

Disposal

• The battery contains materials that are harmful to the environment and must be removed from the appliance before it is discarded.
• When removing the battery, the appliance must be powered off.
• Batteries, chargers, accessories, and packaging should be sorted for environmental-friendly recycling. Do not put them into the fire, water, or soil. Do not dispose of batteries and chargers in household waste!
• If battery leakage contacts skin or clothing, immediately flush with water to avoid irritation and seek medical help.

Troubleshooting

Problem

| Possible cause|

Solution

---|---|---
The appliance does not turn on| Auto protection for overheating| Restart after cooling down
Contact piece on the main body is dusty| Clean the contact piece with a dry cloth
Weak suction| The dry filter is not installed, or the dry filter is dirty| Install the dry filter or dry clean and allow it to dry completely
Brush roller tangled indicator blinking ‘ Voice prompt:
1. Please clean the brush roller
2. Please install the brush roller correctly| 1. The brush roller is blocked
2. The brush roller is not installed| 1. Remove blockages
2. Install brush roller correctly
WiFi indicator is off| WiFi is not connected| Follow the in-app guide to connect to WiFi
CWT empty indicator blinking

Voice prompt: Clean Water Tank empty, please  refill water and cleaning solution

| CWT is empty| Refill CWT
DWT full indicator blinking ‘ Voice prompt:
Please clean Dirty Water Tank | The dirty water in DWT has reached the MAX line| Empty the dirty water and then reinstall the DWT
All lights off in operation | Battery overheat or malfunction| Cool the appliance down and restart
Battery indicator blinking, Voice prompt:

Low battery, please charge

| Low battery| Charge the appliance, or restart
Dust sensor malfunction indicator blinking Voice prompt:
Please begin the self-cleaning cycle | Dirt sensor malfunction or blocked restart| Remove blockages, clean the debris channel, or
Self-cleaning icon blinking | The brush roller is dirty| Start self-cleaning
All indicators blinking together| Motor malfunction| Contact Customer Service

Note: If the above troubleshooting guide fails to provide a solution, please visit our website www.tineco.com for further support.

Warranty

2-YEAR LIMITED WARRANTY

•  Only applies to purchases made from authorized retailers of Tinoco.
• Is subject to adherence to the requirements outlined in this instruction manual, and is subject to further conditions outlined below.

WHAT IS COVERED?

•  Your Tineco appliance has a 2-year warranty against original defects in material and workmanship when used for private household purposes in accordance with the Tineco Instruction Manual.
  Motorized accessories and batteries bought separately come with a 1-year warranty.

• This warranty provides, at no extra cost to you, all labor and parts necessary to ensure your appliance is in proper operating condition during the warranty period.

• This warranty will only be valid if the appliance is used in the country in which it was sold.

WHAT IS NOT COVERED?

Tinoco shall not be liable for costs, damages, or repairs incurred as a result of:

• Appliances purchased from an unauthorized dealer.
• Careless operation or handling, misuse, abuse, and/or lack of maintenance or use not in accordance with the Tineco Instruction Manual.
• Use of the appliance other than for normal domestic purposes, e.g. for commercial or rental
• Use of parts not in accordance with the Tineco Instruction Manual.
• Use of parts and accessories other than those produced or recommended by Tinoco.
• External factors are unrelated to product quality and use, such as weather, modifications, accidents, electrical outages, power surges or acts of God.
• Repairs or alterations carried out by unauthorized parties or agents.
• Failing to clear the blockage and other hazardous material from the appliance.
• Normal wear and tear, including normal wearing parts, such as clear bin, belt, filter, HEPA, brush bar, and power cord (or where external damage or abuse is diagnosed), carpet or floor damage due to use not in accordance with manufacturer’s instructions or failure to turn the brush bar off when necessary.
• Reduction in battery discharge time due to battery age or use.

WARRANTY LIMITATIONS

•  Any implied warranties relating to your appliance including but not limited to the warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty.
• Warranty coverage applies to the original owner and to the original battery only and is not transferable.
• This limited warranty gives you specific legal rights. You may also have other rights which vary by region.
• Manufacturers’ warranties may not apply in all cases, depending on factors such as the use of the product, where the product was purchased, or who you purchased the product from. Please review the warranty carefully, and contact the manufacturer if you have any questions.

WARRANTY SERVICE

Register: We highly recommend that upon purchase, you register your appliance on the Tineco official website (www.tineco.com) and enjoy exclusive benefits.
To register, please enter the last 11 digits of the serial number (found on the back of the appliance).
Failure to register your product won’t diminish your warranty rights.

How to Claim: Please retain your proof of purchase. To make a claim under our Limited Warranty, you need to provide your serial number and the original purchase receipt with the purchase date and order number on it.
All work will be carried out by Tineco or its authorized agency.
Any replaced defective parts will become the property of Tinoco.
Service under this warranty will not extend the period of this warranty.

Contact our Customer Service
Hotline: 1-855-292-8864 or Visit Tineco website
www.tineco.com
for expert customer service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>