Nordval SH105 64GB Video Doorbell User Guide

Nordval SH105 64GB Video Doorbell

DECLARATION OF CONFORMITY
Product Information
For the following

• Product: video doorbell
• Type:SH105

DECLARATION AND APPLICABLE STANDARDS
Hereby, TJM Supplies B.V. declares that the type of video doorbell SH105 series conforms to:
Directive EMC 201<1153/EU and the RoHS directive (2011165/EUJ and its amendment directives 20151863/EU on the restriction of the use of certain hazardous substances In electronic equipment.
The full text of the EU declaration of conformity can be found at the following internet address:
www.nordval.eu/declarillion-of-conformity/
IMPORTAR

WHAT’S IN THE BOX

Please check the box for each of the following items before installing Your video doorbell:

GET TO KNOW YOUR VIDEO DOORBELL

SET UP YOUR VIDEO DOORBELL

1. Attach the wires from the provided power adapter to the terminals on the rear of Your doorbell, and tighten the terminal screws with a screwdriver. Each wire can be connected to each connector. The cable order doesn’t matter.
2. Plug the adapter to your AC outlet Install the doorbell within 5 meters of your 2.4GHz WiFi router. It is suggested to test your doorbell prior to physical installation.
3. Download and Install the ‘CloudEdge’ App to your smartphone . Launch the App and register an account with your mobile phone number or email ID.
   

WIFI SET UP

The video doorbell works with 2.4 GHz WIR, but not with 5 GHz WIFI. Perform the configuration near your WIR router. Launch the CloudEdge app and register an account Then start the WiFi configurations. Follow these steps in the app:

MANAGE YOUR APP PERMISSIONS

PAIR WITH CHIME

1. Tap on ”….”and enter Into Settings-> Basic function, select Wireless Chime page (picture 4).
2. A short dick on the reset button behind the chime (picture 51 and the LED Indicator wlll flash blue, Indicating the device Is In pairing mode.
3. Tap “Chime Paring'” button in the app (picture 41 and the video doorbell will send a wireless pairing signal to the chime. Pairing succeeds and the indicator on the Chime will be in solid blue. All set! You can push the video doorbell button to test the result

Select ringtone
Enter by going to Settings-> Wireless Chime, there are 4 ringtones available (picture 4).

VOLUME CONTROL
Swipe the Ring Volume bar to control the volume level for the chime (picture 4).

CONNECT THE CHIME
Supply power to the chime. The chime can be powered by an USB compatible phone charger (DCSV 1A). You can also plug the chime to the use port on ycur PC/notebook to supply power.

DISCONNECT THE CHIME

1.  Press and hold reset button on the chime for about seconds until the indicator flashes blue twice, and the chime will be restored to factory default
2. You can also tap on •one button untie• (picture 4) In the App to release the connection between the video doorbells and the wireless chimes.

RUN A TEST

After setup, tap on the live view window In the app for a test. Then take ycur video doorbell outside to the Installation spot and run a test there. Make sure the installation  spot Is covered by strong 2.4 GHz WIFI signal.
Note: If the video quality from the video doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot, or use a Wi-Fi extender.

LIVE VIEW INTERFACE

LEAVE VOICE MESSAGES

You can pre-install 3 voice messages (Max. 1 O seconds per message) into the video doorbell, which enables you to quickly respond to your visitors when you are not convenient to answer the video doorbell.

Steps: Setting-> Basic function -> Host Leaves Message -> Press and hold this Icon to record voice messages –> Play the selected voice message when answering a call.

RECORDING&: HISTORY PLAYBACK

The video doorbell comes with Event recording by default. It will record visitor calls and motion detection events. You can also enable Full day recording In the Settings–> SD card.

Tap History to play the videos recorded on the MicroSD card.

INSTALLATION STEPS

The video doorbell works with a 12V DC power source (power adapter provided), as well as an existing 12V-2AV AC hardwire power source. It enables you to make use of your existing doorbell wires.

Note:
You need to bypass your indoor mechanical chime to provide sufficient power to the SH105 video doorbell.

SELECT A LOCATION FOR YOUR VIDEO DOORBELL

Determine the mounting position of the doorbell. Check if you can reuse the existing holes on the wall. If not drill new holes to mount your video doorbell. It is suggested to mount the doorbell at least 120 cm above the ground for optimal angle of view and best motion detection performance.

OPTION 1 – CONNECT TO YOUR EXISTING DOORBELL POWER (12VOL T)

To replace your existing doorbell and mechanical chime, please follow below Installation steps:

1.  Shut off power at the fusebox.
2. Bypass your Internal Doorbell Chime with the provided “jumper” wire.
   In most cases, the existing doorbell circuit looks similar to the Image below. Remove the cover of the Indoor chime and loosen the “Front” and “Transformer” terminal screws. Use the provided jumper” wire to connect the two terminals, and replace the chime cover.

3.  Replace your existing doorbell.

4. Restore power at the fuse box. and your doorbell ls ready for use.

OPTION 2 – USE THE INCLUDED POWER ADAPTER

Hardwire your doorbell with the provided DC12V power adapter.

FREQUENTLY ASKED QUESTIONS

• Is the video doorbell powt1red by battery?
  No, this video doorbell requires constant hardwire power supply. Compared to battery powered doorbells, this wired video doorbell has more advanced features, like supporting full day recording. no delay quick response to visitor calls, and smaller In dimension, fitting Into narrow door frames.

• How to connect the hardwire to the doorbell? Does the cable order matter?
  Your doorbell works with both DC 12V and AC 12V  24V hardwire power source. There are 2 terminal screws on the rear of your doorbell, and you can connect each wire to each connector screw. The cable order doesn’t matter.

• I cannot set up the video doorbell to my WIFI network.
  

1.  Device works with 2.4GHz WiFi only, but not support 5GHz WiFi.
2.  WiFi signal is not strong enough, try to keep the video doorbell near the WiFi router when setting up.
3. The WIR password Is wrong. Please check 1f there are special characters In the password, or the ne1’Mlrk Is specially encrypted.

• How do I know if I have 2.4G or 56 WIFI?
  Please check the user manual of your Router or call the network operator for help.

• Does It work with Goo11e Home or Alexa?
  Yes. The Nordval SH105 works with Google voice assistant as well as Amazon Alexa.

  ---

• Can I only vi-my video doorbell when I am connected to the same WIFI network. or can i view it over Internet from anywhere?
  You can view the video doorbell from anywhere, as long as your doorbell ls connected to the Internet and you have Internet connection on your smart device.

  ---

• Do any of the recordings get saved to the cloud? Or ls It monthly saved In the built-ln SD CINI?
  It supports SD card recording as well as cloud storage. You can activate the cloud storage service In App.

  ---

• What happens when the SD is full?
  When the memory card is full, the doorbell automatically erases the oldest footage.

• Why does It lose connection to WIFI?
  Please check the network connection of your smart device and the WIFI router. If the network signal Is not strong enough, you may need to move your router closer to the video doorbell, or use extender.

• Can motion detection be disabled?
  Yes. Recording Is tr1ggered by detected motions. You can adjust the sensitivity or disable mod on detection In the settlings menu.

• Can I use 2 or more doorbells in the same house7
  Yes, you can add more than one Nordval SH105 at the same house.
  Push button LED light explanation;

• Does It support customized Motion Detection Zones?
  Yes It does. Go to Settings -> Motion Detection -> Alarm Area .. Use your finger tips to draw one or more customized motion detection zones and save your settings, the orange zones are active motion detection zones.

• How long Is my video doorbell covered under warranty?
  We provide a 24-month warranty on all our products after purchase (with some exceptions). Unfortunately we cannot treat products that have become defective due to incorrect use, fall damage, water damage, etc.
  Share your video doorbell with other users
  Steps: Settings-> Device Share_.. Tap on• Add• .,. Tap on• Account”-> Type in account ID _.,. Confirm Sharing.
  Is your question not answered?
  For more tips, go to: www.nordval.eu/en/products- faq/

SPECIFICATIONS SH105

Video doorbell

Product name

Color/size

| Nordval SH105 Black</115x45x27mm|  | Operating temperature Humidity| -2o•c – 5o•c

<90’16 (no condensation}

---|---|---|---|---
Weight| 100g|  | Storage type| Micro SD card (max 128GB}
Video resolution| 2304 x 1296 px|  | Cloud storage| Optional
Viewing angle

Sensor

| 166° degrees

1/3″CMOS

|  | ****

Recording activated

| By PIR motion sensor or Full Derry R ecording
Lens| 1.7mm|  | Warranty| 2years                                 _J
Motion sensor| Yes|  |  |
Night Vision| High power LED with ICR|  |  |
Stream quality| 2K QHD|  |  |
Audio| 2-wrr; audio|  | Chime|
Noise cancellation| Yes|  | Color/size/weight| Black/060 x 24mm/33g
WDR| Yes|  | Door bell| Maximum 100 dB
WIFI frequency| 2.4GHz – 2.4835GHz|  | Frequency| 433 MHz-868 MHz
Standard| IEEE 802.11 b/ g/n|  | Power supply| USB(type A)
Live View speed| Within 2-4 sec|  | Power consumption| 0,2W
Waterproof| Yes-lP65|  | Connection| Wireless (RF}

Power

| Hardwire 12V-24V M:.|  | Place of use| Indoors
 | or12VDC|  | Operating temperature| -30-C – 70-C
Power consumption| 4.SW(Max}|  | Humidity| <90’16 (no condensation}

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>