GREENCREATIVE 17A21 LED HID Replacement Lamp Installation Guide

: June 6, 2024
: GREENCREATIVE

Table of Contents

INSTALLATION STEPS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LED HID REPLACEMENT LAMP
INSTALLATION GUIDE
WARNING GREENCREATIVE 17A21 LED HID Replacement Lamp -
Replacement

For model #: 17A21/xxx/277V/DIM, 24HID/xxx/277V/E26/DIM, 34HID/xxx/277V/E26/DIM
Where xxx means 824-965 which indicates CRI and color temperature
Pour les produits suivants: 17A21/xxx/277V/DIM, 24HID/xxx/277V/E26/DIM, 34HID/xxx/277V/E26/DIM

CAUTION – IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER.
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Installation should be performed only by a qualified electrician in accordance with the National Electrical Code and relevant local code.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions written and shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
This item is rated at 120-277V. Installer must determine whether line voltage 120-277V is available at the luminaire before installation.
Not intended for use with emergency exit fixtures or emergency exit lights.
Not for use with luminaire ballast.
Do not use if product is damaged.
This lamp is available for dimming with 120V line voltage only and might not be compatible with all dimmers. Please visit www.greencreative.com for compatibility information.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
This luminaire has been modiﬁed to operate LED lamps” shall be marked on the retrofit luminaire where readily visible by the user during normal maintenance including re-lamping.
Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing suitable listed wiring connectors.
SUITABLE FOR DAMP LOCATIONS. Suitable for use in wet locations when used in an outdoor-rated fixture. Not for use where directly exposed to the weather or water.
Suitable for use in totally enclosed fixtures.
Complies with Part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.
No external weight or mechanical force should be applied to lamp or components.
THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
The minimum lamp compartment dimensions are described below:

| Model Number| 17A21/xxx/277V/DIM| 24HID/xxx/277V/E26/DIM| 34HID/xxx/277V/E26/DIM
---|---|---|---|---
Low bay installation| Lamp Compartment
Dimensions| Diameter| 6″| 6″| 8″
Height| 8-1/2″| 8-1/2″| 11″
Post top installation| Diameter| 3-9/16″| 3-9/16″| 8″
Height| 7-7/8″| 7-7/8″| 11″
Maximum Lamps in Luminaire| 1| 1| 1

INSTALLATION STEPS

Read all WARNINGS before continuing this section.
Ensure power to the fixture is 120-277V.
Make sure POWER IS TURNED OFF AT THE SOURCE.
Remove lens if applicable, remove cover and lamp.
Before rewiring, check the ballast type and refer to the relevant diagram.
If fixture is new without ballast, please refer to Diagram 1.
If fixture is connecting with ballast, please refer to Diagram 2.
Wire existing socket wires with line voltage power in accordance with NEC and local codes in the ballast compartment.
Install lamp into the wired lampholder.
Affix supplied modification sticker to the existing fixture so it is visible during re-lamping.
Turn power on at the source and installation is complete.