SWIT CURVE500 HDMI 150m 500ft Wireless HD System User Manual

Model I CURVE500-V2.0 Tx CURVE500-V2.0 Rx
500ft Wireless HD

User Manual
Please read this user manual throughout before using
Ver:A

Preface

All internal technologies of this product are protected, including device, software, and trademark. Reproduction in whole or in part without written permission is prohibited.
All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners.
Due to the constant effort of product development, SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice.
The warranty period of this product is two years, and does not cover the following:

1. Physical damage to the products
2. Any damage or breakdown caused by use, maintenance, or storage not according to the user manual’s introductions.
3. The attenuation of signal quality resulting from being used in any special environments.
4. Any damage caused by not powering the product by package supplied power adaptor.
5. Any damage or breakdown not caused by the product’s design, workmanship, manufacturing, quality, or unauthorized repairs or parts replacement or other operations.

For any suggestions and requirements on this products, please contact us, please contact us through phone, fax, Email, etc.
SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R.China
Tel: +86-25-85805753
Fax: +86-25-85805296
Email: contact@swit.cc
http://www.swit.cc

Safety Precautions

Please follow the safety precautions before using. The following conditions are not covered by warranty.

1. Unauthorized repairs or other Unauthorized operations.
2. Inappropriate placement includes but is not limited to lighting, fire, exposure to rain, water, or gas.
3. Using the wrong power supply.

Warning

• Do not get any liquid inside the products
• Do not block the ventilation openings or put substances inside, in order to avoid short circuits, fire, or electric shock.
• Do not place the product in the rain or moisture to avoid electric shock or fire. its

Danger

• Switch the power off before connecting other devices.
• Power socket: Make sure the power socket is under the voltage range of the product to avoid short circuits, electric shock,s, and fire.
• Power cable: Make sure the power cable is not pressed or tightened by any items or weights.
• Power Load: Do not exceed the load on the wall outlet, extension cable, or another porous receptacle to avoid fire or electric shock.
• Lightning: Disconnect the power cable if it is lightning or not used for a long period of time.

Working environment

• Please don’t lay the product in any unstable place to avoid fallen damage.
• Please don’t use the product in a place overheating, undercooling, or with lots of moisture, or nearby strong magnetic devices.
• Please don’t lay the product on a metal shelf, in order to ensure effective wireless transmission.

Packing list

Features **

**

® HDMI Wireless transmission
Support up to 1080P50/60Hz HDMI wireless transmission.°
C) 150 meters transmission distance
In open outdoor area, the effective transmission distance is approx. 150 meters (line of sight).
® Wireless frequency
The system adopts 5180-5220MHz and 5760-5820MHz Wireless frequency band(CURVE500-V2.0 Tx

Frequency Band and Frequency Point

CHOO| 5180MHz| CH04| 5780MHz
CHO1| 5200MHz| CH05| 5800MHz
CH02| 5220MHz| CH06| 5820MHz
CH03| 5760MHz| /| /

The system adopts 5182.5-5282.5MHz and 5762.5-5822.5MHz Wireless frequency band (CURVE500-V2.0 Rx).

Frequency Band and Frequency Point

CHOO| 5182.5MHz| CH04| 5782.5MHz
CHO1| 5202.5MHz| CH05| 5802.5MHz
CH02| 5222.5MHz| CH06| 5822.5MHz
CH03| 5762.5MHz| /| /

• Pairing mode
  Support auto-pairing connection and manual switching of frequency points.

•  Encryption Support AES 128-bit encryption to protect the transmission.

•  All-Metal Shell Both the transmitter and receiver adopt a metal shell that is durable and solid.

• All hardware design The wireless system is hardware and plug-and-play designed, without installing software, easy to set up.

Remark:

1.  The transmission distance may be different and depending on surroundings, radio wave conditions, buildings, etc., the 150 meters transmission distance maybe not be guaranteed.
2. The wireless transmission might be interrupted if there’re other devices of 5Ghz wireless bandwidth used in the same location.
3. Signal reception may be affected by the position, height, and angle of devices. If the reception video is not stable, please physically adjust placement for the optimized signal.
4. Set the antennas straight up and set the receiver higher to enhance the transmission efficiency.

Appearance Instruction

Transmitter CURVE500-N2.0

1. 1.  **Antenna**

2. Product label
3. Link: Wireless status indicator
4. Video : Video signal indicator
5. Power: Power status indicator
6. Pair: 0.96-inch OLED
7. Installation thread :1/4″-20 Use the package supplied articulating arm trestle to install the device to the camera.
8. USB: Micro USB, software upgrade interface
9. HDMI in: HDMI input (standard HDMI-A type connector).
10. Battery plate: “F” plates can be used. We recommend SWIT batteries like: S-8972, S-8970, S-8770, S-8975 compatible with SONY ” L” series NP-F770/970. (11)
11. HDMI LOOP : HDMI loop out (standard HDMI-A type connector).
12. ON/ OFF: Power switch
13. DC in:Support DC 7—17V input,5.5mm(outer diameter)/2.0mm(inner diameter) Outside: negative, Inside: positive

The description of LED status indicator

Cu RVE500-V2.0
Transmitter| Power| Constant On| Power connected and switched on
Off| Power disconnected and switched off
Video| Constant On| There is recognizable video signal input
Flash| There is no recognizable video signal input
Link| Constant On| The wireless network connection is normal
Flash| The wireless network connection is abnormal

Receiver CURVE500-V2.0

1. Antenna
2. Product label
3. Link: Wireless status indicator
4. Video:Video signal indicator
5. Power: Power status indicator.
6. Pair: Pair
7. Installation thread: 1/4″-20 thread, Use the package supplied articulating arm trestle to install the device to the camera
8. USB: Micro USB, software upgrade interface
9. HDMI OUT1: HDMI output (standard HDMI-A type connector).
10. Battery plate: “F” plates can be used. We recommend SWIT batteries like: S-8972, S-8970, 5-8770, 5-8975 compatible with SONY “L” series NP-F770/970/.
11. HDMI OUT2: HDMI output (standard HDMI-A type connector).
12. ON /OFF: power switch
13. DC in:Support DC 7-17V input,5.5mm(outer diameter)/2.0mm(inner diameter)

Outside: negative, Inside: positive

The description of LED status| indicator|
---|---|---
Device| LED indicator| Status| Description
CURVE500-V2.0
Receiver| Power| Constant On| Power connected and switched on
Off| Power disconnected and switched off
Video| Constant On| There is recognizable video signal input
Flash| There is no recognizable video signal input
Link| Constant On| The wireless network connection is normal
Flash| The wireless network connection is abnormal

Setup connection

1.  Connect the HDMI in the interface of the CURVE500-V2.0 transmitter to the HDMI out of the camera or video output device.

2. Connect the HDMI outl interface of the CURVE500-V2.0 receiver to the HDMI in of the monitor or switch station.

3. Connect the HDMI out2 interface of the CURVE500-V2.0 receiver to the HDMI in of the monitor or switch station.

4. Connect the power supply of the CURVE500-V2.0 transmitter and receiver, the “power” indicator will light up,”Link” and “Video” indicator light up when the transmitter and receiver have identifiable signal inputs and connections, “Link” and “Video” indicator will flash if transmitter and receiver have no identifiable signal input.

Tips:

1.  put the power switch to “ON” when connecting the power supply of the CURVE500-V2.0 transmitter and receiver.
2. The CURVE500-V2.0 transmitter only supports the HDMI video input interface, and the system automatically detects the input video interface.
3. The HDMI OUT1 of the CURVE500-V2.0 receiver is the main output port. HDMI OUT2 is available when HDMI OUT1 is working.

 Pairing

1. Connect the HDMI in the interface of the CURVE500-V2.0 transmitter to the HDMI out of the camera or video output device.
2. Connect the HDMI out interface of the CURVE500-V2.0 receiver to the HDMI in of the monitor or switch station.
3. Connect the power supply of the CURVE500-V2.0 transmitter and receiver, the “power” indicator will light up “Video” and the “Link” indicator will flash.
4. Long pressing the “pair” button in both transmitter and receiver, The “Link” indicator of transmitter and receiver flash and pair, “Link” indicator lights up, the automatic pairing is successful and enters the encrypted transmission state.
5. Press the “Pair” button twice partly to upgrade the firmware, the “Video” indicator quickly flashing during the upgrade process, the “Video” “Link” indicator light up with red, the firmware upgrade successfully. The “Video” “Link” indicator flash when the upgrade is failure

Tips:

1.  When pairing, the transmitter and receiver need to be paired Simultaneously.
2. During normal use, ensure that the wireless device used has been paired and successfully paired.
3. The paired transmitter and receiver will be automatically connected after booting up. It is no need to pair again.
4. Please keep the transmitter and receiver in a distance of 1-2m to avoid pairing failure.

The way to get the best effect of Wireless Transmission

1. Set the antenna on both transmitter and receiver vertically straight up. No request to spread. (Fig.1)
2. Set the receiver as high as possible to avoid interference.
3. Avoid walls, trees and water to reduce signal attenuation.

**Troubleshooting

**

If the receiver failed to output video correctly, the possible causes are as below; please find the solution from the following chart:

The receiving
video| Possible causes| Solution
---|---|---
No display| The transmitter or the receiver is not powered on| Check power connection and switch on the transmitter and receiver
The antennas are not installed properly and screwed tightly| Install the antennas properly and screw tightly of both transmitter and receiver
Bad connection of video cable| Check video cable connection of both transmitter and receiver
Video format is not supported| Change the output video format of the camera
Poor
Video quality,| Bad connection with video cable| Reconnect reliably
The wireless transmission is disturbed by the environment| Wait for 1 minute or reboot the transmitter and receiver
The transmission distance is out of effective range| Put the transmitter closer to the receiver

Specification

(60/59.94/50/30/29.97/25/24/23.98)

Wireless frequency| FULL:5180-5220MHz and 5760-5820MHz
Modulation mode| OFDM Support 16QAM,64QAM,QPSK,BPSK modulation mode
Transmission distance| 150m (Line of sight)
Power consumption| <7.5W| <7W
Input voltage| DC/Battery:7^-47V| DC/Battery: 7″-17V
Working environment| Tem peratu re : 0°C-440°C
Dimension| 114.18x 69.55 X28 (mm)| 114.18 x 69.55 x28 (rnm)
Net weight (Without antenna)| 173.2g| 173.6g
Net weight (With antenna)| 180.8g| 181.2g

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R.China
Tel: +86-25-85805753
Fax: +86-25-85805296
Email:contact@swit.cc
http://www.swit.cc

Documents / Resources

| SWIT CURVE500 HDMI 150m/500ft Wireless HD System [pdf] User Manual
CURVE500-V2.0 TX, CURVE500-V2.0 RX, CURVE500 HDMI 150m 500ft Wireless HD System, CURVE500, HDMI 150m 500ft Wireless HD System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>