Remote Controls GTTX Remote Coding Instructions

June 6, 2024
Remote Controls

Remote Controls GTTX Remote Coding

Remote Controls GTTX Remote Coding
PRODUCT

GTTX REMOTE CODING PROCEDURE

Alarm GT

To add a new transmitter to your alarm, simply follow the procedure below:

  • Turn the vehicle’s ignition on.
  •  Immediately press and hold the Left button on the Original remote control until the siren starts to beep (approximately 4 seconds) and then release the button.
  • Immediately press and hold the same (Bottom) button on the New remote control for at least 4 seconds.
  • Turn the vehicle’s ignition off.
  • The new remote control is now programmed into the alarm.

GTTX REMOTE CODING PROCEDURE

Alarm RES4601v2

To add a new transmitter to your immobiliser, simply follow the procedure below:

  • Turn the vehicle’s ignition on.
  • Immediately press and hold the LEFT (Button 1) button on the original remote control until the indicators start to flash (approximately 4 seconds) and then release the button.
  • Immediately press and hold the LEFT (Button 1) button on the new remote control for at least 4 seconds.
  • Turn the vehicle’s ignition off.
  • The new remote control is now programmed into the immobiliser.

GTTX REMOTE CODING PROCEDURE

Alarm RA97 RA98 RCTX2-434 → GTTX

To add a new transmitter to your alarm, simply follow the procedure below:

  • Turn the vehicles ignition on.
  • Immediately press and hold the RIGHT button on the original remote control until the siren starts to beep (approximately 4 seconds) and then release the button.
  • Immediately press and hold the LEFT button (1) on the new remote control for at least 4 seconds.
  • Turn the vehicles ignition off.
  • The new remote control is now programmed into the alarm.Remote Controls GTTX Remote Coding FIG-1

GTTX REMOTE CODING PROCEDURE

Alarm RCA98 RCTX2-434 → GTTX
To add a new transmitter to your alarm, simply follow the procedure below:

  • Turn the vehicle’s ignition on.
  • Immediately press and hold the RIGHT button on the original remote control until the siren starts to beep (approximately 4 seconds) and then release the button.
  • Immediately press and hold the LEFT button (1) on the new remote control for at least 4 seconds.
  • Turn the vehicle’s ignition off.

Remote Controls GTTX Remote Coding FIG-2

GTTX REMOTE CODING PROCEDURE

Alarm RES98 RCTX2-434 → GTTX

To add a new transmitter to your immobiliser, simply follow the procedure below:

  • Turn the vehicle’s ignition on.
  • Immediately press and hold the RIGHT button on the original remote control until the indicators start to flash (approximately 4 seconds) and then release the button.
  • Immediately press and hold the LEFT button (1) on the new remote control for at least 4 seconds.
  • Turn the vehicle’s ignition off.
  • The new remote control is now programmed into the immobiliser.

Remote Controls GTTX Remote Coding FIG-3

GTTX REMOTE CODING PROCEDURE

Alarm CLX/CLXI No. Remotes 15 RCTX2-434 → GTTX

  • Press and hold the red (right) button, of an existing (learnt in) remote control, for approximately 5 seconds or
  •  until the blinkers begin the flash again.
  • Immediately after the blinkers begin flashing or after holding the red button of the existing remote control, release that button.
  • Immediately after releasing the button off the existing remote control press the button 1 of the new remote control times for duration of 1 second each time.
  • The new remote control should now work with the CLX/CLXI.
  • If this doesn’t work re-try this procedure from the beginning.

Remote Controls GTTX Remote Coding FIG-3

GTTX REMOTE CODING PROCEDURE

Alarm RCX V2 No. Remotes 15
Your RCX / RCXi incorporates a unique code learning system. This enables extra remotes to be added with ease if necessary. Up to 15 remotes can be added to system if required. To learn in a new remote control:

  • Press and hold buttons 1 & 2 of an original (learnt in) remote control together for approximately 5 seconds or until the indicators begin to flash.
  • Immediately release the buttons on the original remote then press and hold button 1 of the new remote control for approximately 3 seconds.
  • Your RCX should now have learnt the new remote control – test this by comparing functions with the original remote control. If the learn procedure was unsuccessful, retry the procedure from step one.

GTTX REMOTE CODING PROCEDURE

Alarm RCV / RCVi RCX / RCXi 2 Channel RX No. Remotes 15
To learn in a new remote control

  • Press and hold button 1, of an existing (learnt in) remote control, for approximately 5 seconds or until the blinkers begin to flash again.
  • Immediately after the blinkers begin flashing or after holding the button 1 of the existing remote control, release that button.
  • Immediately after releasing the button of the existing remote control press button 1 of the new remote control for 3 seconds then 5 times for a 1 second duration each time.
  • The new remote control should now work. If this does not work the first time re-try this procedure from the beginning.

GTTX REMOTE CODING PROCEDURE

Alarm RXPRO RXPRO4 RXPROSOL

Enter Programming:

  • Mode Press and hold button 2 on the remote control
  • Connect to power
  • Keep holding button 2 until the display light stop scrolling, you are now in programming mode.

Adding new remote:

Press button 3 repeatedly until the channels lights indicate one of the output channels you wish to program. Select a channel that you wish to operate with a remote control i.e. not a channel that you wish to operate with a wireless detector.

Press button 2 until the feature lights are on as shown
Press button 1 to set the feature light(s) to flashing. NOTE: By default the feature light(s) will be flashing, if not press button 1 to set to flashing.

Press button 2 repeatedly until the feature lights are off as shown.

Press and hold button 1 until the channel lights(s) begin to flash

Immediately press button 1 repeatedly on the new remote control you wish to learn in until the channel light(s) stop flashing.

Press and hold button 2 on the new remote control until the lights start scrolling. The new remote control has now been learnt in.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals