V-TAC VT-80060 LED Waterproof Fitting Instruction Manual
- June 4, 2024
- V TAC
Table of Contents
V-TAC VT-80060 LED Waterproof Fitting
Specifications
| MODEL | SKU | WATTS | LUMENS | CRI | DF | BEAM ANGLE |
|---|---|---|---|---|---|---|
| VT-80060 | 23087 23088 | 18W | 1900Lm | 80 | 0.7 | |
| VT-80120 | 23083 23084 | 36W | 3900Lm | 80 | 0.9 | |
| VT-80150 | 23085 23086 | 48W | 5200Lm | 80 | 0.9 |
LIFE SPAN: 25,000 Hours
ON/OFF CYCLE: >15,000
INPUT POWER: AC: 220-240V 50/60 Hz
Installation Instructions
WARNING
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a qualified electrician.
- The light source of this luminaire is not replaceable. When the light source reaches its end of life, the whole luminaire should be replaced.
- If the external flexible cable or cord of this luminaire is damaged, it should be exclusively replaced by the manufacturer, his service agent, or a qualified person to avoid hazards.
MULTI-LANGUAGE MANUAL QR CODE: Please scan the QR code to access the manual in multiple languages.
Installation Steps:
MODEL VT-80060 VT-80120 VT-80150
- Turn off the power.
- Mark the proper drilling point as per the chart.
- Fix the brackets onto the ceiling using the offered screws. Open the junction box cover of the body with a screwdriver.
- Ensure the cable length is appropriate.
- Install the lamp to the ceiling clips.
- Open the right side lid to connect wires.
- Insert cable through the waterproof connector and wire it into the terminal block. Ensure LIVE = BROWN; NEUTRAL = BLUE.
- Close the right lid.
- Turn on the power and test.
FAQ
- Q: How do I know when to replace the luminaire?
- A: The luminaire should be replaced when the light source reaches its end of life, typically after 25,000 hours of use.
- Q: Can I replace the light source myself?
- A: The light source of this luminaire is not replaceable. The entire luminaire should be replaced when needed.
- Q: What should I do if the external cable is damaged?
- A: If the external flexible cable or cord of this luminaire is damaged, it should be replaced by the manufacturer, service agent, or a qualified person to avoid hazards.
More Info
TECHNICAL DATA
INTRODUCTION & WARRANTY
Thank you for selecting and buying the V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at your best. The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.
WARNING
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a qualified electrician.
- The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard.
MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages
In case of any query/issue with the product, please reach out to us at: support@v-tac.eu For More product ranges, inquiry please contact our distributor or nearest dealers. V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
This marking indicates that this product should not be disposed of with other household wastes
Caution, risk of electric shock.
INSTALLATION INSTRUCTION
- Turn off the power.
- Mark the proper drilling point as per the chart.
- Fix the brackets onto the ceiling by offered screws. Open the junction box cover of the body with a screwdriver.
- Make sure the cable length is appropriate.
- Install the lamp to the ceiling clips.
- Open the right side lid to connect wires.
- Insert cable through the waterproof connector and wire it into the terminal block. Make sure L and N are wired to correct holes. (LIVE = BROWN; NEUTRAL = BLUE)
- Close the right lid.
- Turn on the power and test.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>