SOLLA 5000LM Motion Sensor Light Outdoor User Manual

: June 6, 2024
: SOLLA

Table of Contents

SOLLA 5000LM Motion Sensor Light Outdoor
SPECIFICATIONS
PRE- INSTALLATION
- Mounting Height and Location
INSTALLATION
Installation Procedure
OPERATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Solla

SOLLA 5000LM Motion Sensor Light Outdoor

SOLLA 5000LM Motion Sensor
Light Outdoor SAFETY INSTRUCTION

DO NOT install the fixture near an air condition unit or flammable materials.
DO NOT install it in a place with limited ventilation, high vibration level or high ambient temperatures.
DO NOT look directly at the light source when it is on, as this may cause irreparable damage to the eyes.
Risk of suffocation! Keep small parts and packaging materials away from children.
Non-professionals are forbidden to disassemble, repair or modify this product.

SPECIFICATIONS

◉ SPECIFICATIONS|
---|---
| | ****

H: 5000LM±10%

CRI

| | AC100V-240V

;,,so

PRE- INSTALLATION

Mounting Height and Location

SOLLA 5000LM Motion Sensor Light Outdoor 1

KHp the fixture level with the ground.
Leave at let 1 O cm apace from the top or selling and aide wall.
Install the fixture on a flat surface and in a relatively stable place.
It is recommended to install the light under eaves or awnings.

INSTALLATION

SOLLA 5000LM Motion Sensor Light Outdoor 3

Installation Procedure

SOLLA 5000LM Motion Sensor Light Outdoor 4

Install the Iron Plate (A) on the Junction box In the right direction and light it with screws (B).
Remove the Wiring Cover (G) from the light
There is a rubber plug in the hole (H), drill a hole in the rubber plug and lead the electric wires from the junction box through the hole (H). Remove the silicone plug amid the Wiring Cover (G), then install the Wiring
Cover (G) on the junction box and tight it with screw (C). Then cover the hole with a silicone plug.
Wiring the Light Fixture
CAUTION: Make sure the connection is correct as shown below.
The ends of the main cable should leave enough length to make it easy to make connections.
Connect the main cable to the Connector Block.
Insert the white wire from the original power supplier into the terminal marked ‘N’.
Insert the black wire from the original power supplier into the terminal marked ‘l”.
Insert the green/yellow earth wire from the original power supplier into the terminal marked “* •.
Note: We recommend that the clients purchase the extension cable in case the electric wires from the junction box are not long enough to meet the terminal in the Wiring cover.

OPERATION

Lamp Heads AdJustment
- The left and right lamps can be adjusted 1 BO degrees up or down. The middle lamp can be adjusted 90 degrees up or down.
- The left and right lamps can be adjusted 90 degrees backward or forward.
- The triangle bracket can be adjusted 45 degrees left or right.
Motion Sensor Adjustment
- The sensor can be adjusted 00• degrees left or right.
Detection Range
Warm-up State
- Warm-upstate The light fixture will enter a warm-up state for 20 seconds when it is energized with AC100·24ov for the first time: The three adjustable Ilg ht heads are switched off, the t 2 function indicators will light gradually for 20 seconds; 20 seconds later, three heads will light and the light fixture is ready to be set.
- Function indicator When the light on standby mode detects the motion, four-function indicators showing the current level will keep the light on for 5 seconds.
Custom Settings

Press the setting buttons to customize your light fixture:
DIST: The sensor will detect motion within 72ft/40ft/20ft
MODE:

  * Infrared human body sensing mode: The light fixture will be triggered when the sensor detects the human body.
  * Dawn to Dusk mode: The light fixture will turn off in the daytime and turn on at night automatically, light up for 10 hours.
  * Test mode: The light fixture will light up for 5 seconds. The fixture will light up for 10 mins/5 mins/ 1 min when the motion is detected.

DIM: The light fixture is dimmable.(5000Im/4000Im/3000Im)