BRISTAN Quest Basin Bath and High Neck Taps User Guide
- June 6, 2024
- BRISTAN
Table of Contents
Quest Basin Bath and High Neck Taps
User Guide
IMPORTANT: Please keep these instructions for future reference and request of replacement parts
Introduction
Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed this product with your enjoyment in mind. To ensure that it works to its full potential, it needs to be fitted correctly. These fitting instructions have been created to give you all of the information you need and, if you need any further help, please do not hesitate to give us a call on 0844 701 6273.
Safety Note
Please read these instructions thoroughly and retain for future use.
All products manufactured and supplied by Bristan are safe provided they are
installed correctly, used correctly and receive regular maintenance in
accordance with these instructions.
These fittings need to be installed in accordance with and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and
Scottish Byelaws 2004.
Specification
This product is suitable for use at all supply pressures. If installed at low
pressure (tank fed), then the minimum distance from the outlet of the nozzle
to the underside of the cold tank should be approximately 2 metres to ensure
adequate performance.
Operating pressure range (bar)
Maximum static pressure – 10.0 bar
| Min. | Max. |
|---|---|
| 0.2 | 5 |
NOTE: – Nominally equal (balanced) inlet supply pressures are recommended for optimum performance.
Installation
- Identify all components and check for completeness, particularly before arranging to fit.
- Install the taps (1) onto the basin/bath or sink. The backnut (3) and backnut washer (2) are used to secure the tap to the surfaces of the basin/bath/sink.
- Connect the hot and cold water supplies.
- Turn on both water supplies, open both taps letting the water run for a few minutes to check all joints and connections for leaks.
Contents
1. Tap Body x2
2. Backnut Washer x2
3. Backnut x2
a. Valve x2
b. Spline Adaptor x2
c. Screw x2
d. Handle x2
IMPORTANT – PLEASE READ
These fittings need to be installed in accordance with the following
Installation Requirements and Notes (IRN) to ensure they meet the requirements
of the Water Supply (Water Fittings) Regulations 1999 and the Scottish Byelaws
2004.
IRN R001
See text of entry for Installation Requirements or Notes.
IRN R006
This tap or combination tap assembly has a Type AUK3 air gap and is therefore
for installation in any premises to protect against a backflow risk up to a
Fluid Category 5.
Cleaning & Maintenance
Your fitting has a high-quality finish and should be treated with care to
preserve the visible surfaces.
All finishes will wear if not cleaned correctly. The only safe way to clean
your product is to wipe it with a soft damp cloth. Stains can be removed using
washing-up liquid. All bathroom cleaning products (powders and liquids) will
damage the surface of your fitting, even the non-scratch cleaners.
NOTE:- Never use abrasive detergents or disinfectants or those containing
alcohol, hydrochloric or phosphoric acid.
If the fitting begins to drip:
- Turn off both water supplies.
- Remove the handles (d) by pulling from valve (a) and spline adaptor (b). Then remove screw (c), by unscrewing from valve (a)
- Also, remove spline adaptor (b) to avoid damaging it.
- Using a suitable spanner, remove valve (a). Once removed, carefully clean seating, rubber washer, and ceramic disc.
- Replace all of the above and turn on the water supply.
- If the problem persists please contact our customer services helpline on 0844 701 6273.
This booklet covers product code:
QST ½ C / QST ¾ C / QST HNK C
Helpline
0330 026 6273
Bristan Group Limited
Birch Coppice Business Park, Dordon, Tamworth, Staffordshire B78
1SG
A Masco Company
Website:
www.bristan.com
Telephone: 0330 026 6273
Email: enquire@bristan.com
At Bristan, we want to make things as easy as possible for our customers.
That’s why we offer solid guarantees on all our products, effective from the
date of purchase, to give you peace of mind.
To start your free guarantee, simply scan the QR code and
http://www.bristan.com//register
Register your product.
Alternatively, visit
www.bristan.com/register to register
your product via a computer.
For full guarantee terms and conditions visit,
www.bristan.com/guarantees
FI (QST TAP) – REV. D5
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>