owon CB432-TY Din-Rail Relay User Guide
- June 6, 2024
- owon
Table of Contents
owon CB432-TY Din-Rail Relay
Safety Handling
WARNING : Failure to follow these safety notices could result in fire, electric shock, other injuries, or damage to the relay and other property. Read all the safety notices below before using the relay.Avoid high humidity or extreme temperatures.
- Avoid long exposure to direct sunlight or strong ultraviolet light.
- Do not drop or expose the unit to intense vibration.
- Do not disassemble or try to repair the unit yourself.
- Do not expose the unit or its accessories to flammable liquids, gases or other explosives
Technical Specifications
Technical Specifications
Wireless Connectivity
Wi-Fi| • 802.11 B/G/N20/N40
RF Characteristics| • Operating frequency: 2.4GHz
**Physical Specifications
Operating Voltage| • 100~240 Vac 50/60 Hz
Calibrated Metering Accuracy**| • ≤ 100W ( Within ±2W )
• >100W ( Within ±2% )
Max. Load Current| • 63 A
Operating environment| • Temperature: -20℃ ~ +55℃
• Humidity:
≤ 90% non-condensing
Dimensions| • 81 (L) x 36(W) x 66 (H) mm
Weight| • 148g
Welcome
The Din-Rail Relay CB432-TY is a device with electricity functions. It allows you to control On/Off status and to check real-time energy usage via a mobile App. This guide will provide you an overview of the product and help you to get through the initial setup’
Features
- Tuya compliant
- Support Tap-to-Run and automation with other Tuya device
- Control your home device via Mobile APP
- Schedule the device to automatically power electronics on and off
- Measures Voltage, Current, PowerFactor, ActivePower and total energy consumption of the connected devices
- Supports custom values for overcurrent protection on the App
- Status can be retained with power failure
Installation
Important safety information
- The Din-Rail Relay must be installed and serviced only by qualified electrical personnel.
- Do not touch the terminals of the device during the testing.
- Turn off all power supplying this equipment before installing.
- Make sure that the power supply is off before connecting or disconnecting it to the auxiliary device.
- Always use a properly rated voltage sensing device to confirm power is off.
- Replace all devices, doors and covers before turning on power to this equipment
Failure to follow these instructions will result in death or serious injury.
Please keep the wiring diagram below for future reference
Get to know your device
Reset button
Reset.
- Press and hold the Reset button for about 5 seconds until the LED indicator flashes three times (energy data will be cleared).
ON/OFF button
Press once to switch the relay ON/OFF
LED indicator
The LED status gives the following information of the Relay:
LED status What it means
Rapidly blink EZ mode
Slowly blink AP mode
Yellow LED solid on Device is ON when connected with Router
Red LED solid on Device is ON when disconnected.
No light Device is OFF when disconnected.
-
EZ Mode
(Default): To pair devices quickly. You can set all devices to this mode, and then add devices in batches on your phone. -
AP Mode:
If there are many devices, while you only want to pair one device. You can refer to FAQ1 to configure the network in this mode.
Configure Network
To get started, you will need:
- Connect your phone to the 2.4Ghz Wi-Fi network.
- A mobile phone with a ‘SmartLife’ APP installed
Then follow the steps below
- Power on the Din-Rail Relay
- . Make sure the LED indicator blinks rapidly. If not, please reset it.
Add devices
-
Open your App.
-
. Login with an existing account. If you are a new user, you need to create an account at first.
-
Please click the ‘+’ button at the top right corner of the App to add devices.
-
Select ‘Switch Module’ to add manually the Din-Rail Relay in the ‘Energy’ list.
-
Enter your home Wi-Fi account and password (Only support 2.4Ghz Wi-Fi), then tap the ‘Next’ button. -
Place the router, mobile phone and Din-Rail Relay as close as possible to waiting for connection. Confi rm the green indicator on your device is rapidly blinking, then tap ‘Next’
-
After a successful connection, you can rename the it and click ‘Done’ to complete. (If failed, please refer to FAQ2 to troubleshoot
FAQ
Configure the network in AP mode
-
Reset the device in EZ mode, it will switch to AP mode. The indicator on your device will blink slowly.
-
Then switch the network configuration mode to AP mode at the upper right corner of the APP when you add the device.
-
Place the router, mobile phone and Din-Rail Relay as close as possible to waiting for a connection. Confi rm the indicator on your device is slowly blinking, then tap ‘Next’.
- Find and connect the device’s hotspot in the Wi-Fi list.
- After the connection succeeds, you can rename it and click ‘Done’ to complete the configuration. (If failed, please refer to FAQ2 to troubleshoot)
Wi-Fi configuration of the device failed
- Confirm the entered router password is correct.
- Ensure that the DHCP service is enabled for the router. If not, the IP address will be occupied.
- Please confirm the Wi-Fi network is stable
Put the phone beside your device and make sure they are in the same network environment, try to open a website to judge if the network can be used.
- If your router supports both 2.4Ghz and 5Ghz, please enable the 2.4Ghz channel and add device under 2.4G Wi-Fi channel. You can follow the following step on the App to configure the router.
-
Confirm that both the location permission of phone system and the App are enabled.
-
If you have already upgrade the iOS system to 14, you need to enable the ‘Local network’ of the App
- If it still does not work, it is recommended to change the router and try again.
Device offline
- Confirm whether the Din-Rail Relay is powered on.
- Please confirm whether the home Wi-Fi network is normal, or whether the Wi-Fi name and password has been modified.
- If there still have problems after the above checking, it is recommended to remove the device or change the router to add it again.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>