sygonix SY-4512992 Indoor/Outdoor Christmas Tree Light Instruction Manual

sygonix SY-4512992 Indoor/Outdoor Christmas Tree Light

Intended use

Use this product to decorate interior and exterior spaces (IP44). For safety and approval purposes , you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short- circuiting, fire, electric shock etc. Read the instructions carefully and keep them for future reference. Make this product available to third parties only together with its operating instructions. This product complies with the statutory national and European requirements. All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

• Decorative fairy lights
• Transformer
• Operating instructions

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

• Persons / Product

  • The device is not a toy. Keep it out of the reach of children and pets.
  • Do not leave packaging material lying around carelessly. These may become dangerous playing material for children.
  • The product must not be connected electrically with other light chains or decorations.

• Always check the product for damages before use. Should you discover any damage, cease use of the product. If you discover damages while the product is in use (i.e. damaged transformer), do not touch the product, risk of fatal injury due to electric shock! First remove the power outlet to which the product is connected from the power supply (flip off the fuse and/or automatic circuit breaker and then turn off the residual current operated circuit breaker to disconnect the power outlet at all phases). Now unplug the transformer from the power outlet. Discontinue use of the product immediately, dispose of it in an environmentally friendly fashion.

• Protect the product from extreme temperatures, strong jolts, flammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:

  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

• The lights become hot during operation. Keep the product away from highly combustible materials while operating.

• The mains outlet must be located near to the device and be easily accessible.

• As power supply, only use the supplied transformer.

• Only connect the transformer to a normal mains socket connected to the public supply. Before plugging in the transformer, check whether the voltage stated on the transformer complies with the voltage of your electricity supplier.

• Never connect or disconnect transformers if your hands are wet.

• Never unplug the transformer from the mains socket by pulling on the cable; always use the grips on the plug.

• When setting up the product, make sure that the cable is not pinched, kinked or damaged by sharp edges.

• Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

• For safety reasons, disconnect the transformer from the mains socket during storms.

• This product is designed to be used indoors and outdoors.

• Attention, LED light:

  • Do not look directly into the LED light!
  • Do not look into the beam directly or with optical instruments!

• Never use the product immediately after it has been brought from a cold room into a warm one. The condensation generated could destroy the product. The plug-in power supply unit also involves danger to life by electric shock! Allow the product to reach room temperature before connecting it to the power supply and putting it to use. This may take several hours.

• This product’s flexible power supply cord cannot be exchanged or repaired. If the cord is damaged, the product must be disposed of.

• Carefully separate the individual strands on the chain. Never pull on the LEDs, as this may damage the lights.

• Miscellaneous

  •  Consult an expert when in doubt about operation, safety or connection of the device.
  • Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
  • If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

Product overview

Operation

• Do not set up or operate the product under water.
• Make sure that the cables hang loosely and are not stretched too tightly. Failure to heed this warning may cause the cables to tear.
• Do not connect the product to the power supply while it is still in the packaging. Lay the product out entirely before connecting it to the power supply.
• Do not hang any objects from the product and do not cover the product.

The LEDs are non-dimmable and non-replaceable.

1. Carefully spread the product so that it is not bundled together.
2. Hang the product on the desired surface (e.g. top of a Christmas tree) using the loop.
3. Separate the individual strands as desired.
4. Connect the plug to the correct connector on the transformer.
5. Secure the connection by turning the plug‘s screw cap onto the transformer‘s thread.
6. Connect the transformer to a power outlet.
7. The LEDs will turn on when the chain is connected to the mains.
8. Disconnect the transformer from the power outlet for extended periods of disuse.

The product has no power switch and is always on as long as it is connected to the power supply.

Care and cleaning

• Disconnect the transformer from the power supply before cleaning and allow the LEDs to cool down sufficiently.
• To clean, use a clean, dry, lint-free cloth. For stubborn dirt, slightly dampen the cloth with water.
• Allow the product to dry completely before continued use.

Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At the end of its service life, dispose of the product according to the relevant statutory regulations. You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

• Decorative fairy lights****

• Transformer HS-6V1000mA-IP44(EU)****

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>