BRESSER F004543 BR-80SL LED Effect Lights with yoke Arm and Bowens Fixture Instruction Manual

BR-80SL/120SL
LED effect lights
with yoke arm and Bowens fixture
Art. No. F004543 – F004545 F004544 · F004546

INSTRUCTION MANUAL

 Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

www.bresser.de/download/SL-LED/Manual

GENERAL WARNINGS

DANGER OF BODILY INJURY!
Do not use in the presence of children or animals. Store out of reach of children and animals.
Never touch parts of the device during operation or before it has cooled down completely (approx. 45 min. after switching off)!

RISK OF GLARE!
Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.

RISK OF MATERIAL DAMAGE!
Make sure that no one can trip over connection cables of the device. The device could be knocked over.
The manufacturer accepts no liability for damage to property caused by improper or insufficiently safe installation!
Only use the recommended power supply unit or the recommended rechargeable batteries4 for the power supply!
The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power adapter!

DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of an ELECTRIC SHOCK.
Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat. Check this device, cables and connections for damage before use.
Never attempt to operate a damaged device, or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent. Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.

FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not short-circuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
• Never cover the ventilation slots or cooling fins of the device during operation or until it has cooled down completely!
• Only use the recommended power supply unit or batteries4

IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary.
Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation and before any maintenance and cleaning work.
Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the mains supply.
To disconnect the unit from the mains, always pull the mains plug and never pull the cable!

Do not subject the device to excessive vibrations.

PARTS LIST & SCOPE OF DELIVERY

Model 80SL

Model 120SL

PARTS LIST (FIG. 1+2)

1 Bowens-compatible pick-up ring
2 LED module
3 Fixing screw (tripod connection)
4 Tripod connection
5 Yoke arm
6 Fixing screw (yoke arm)
7 Cooling fins
8 Push button (battery fixing)
9 Battery pick-up| 10 Power connection socket
11 -knob
12CH knob
13 Adjustment knob
14 LCD display  5
15 C14 socket
16 DC power plug
17 C13 plug
18 Mains plug
---|---

SCOPE OF DELIVERY (Fig. 1+2)

LED effect light with yoke arm and Bowens mount (1x)(A), mains adapter with mains and voltage cables (1x)(B), instruction manual
OPTIONALLY USABLE:
recharable battery, accessories with Bowens or compatible connector (for more information see “11 Technical data”)

POWER SUPPLY:

NOTE: This device cannot be operated by battery and mains power at the same time! Before commissioning, make sure that only one of the two power sources is active. If both power sources are active during commissioning, this can lead to irreparable damage to the device! The manufacturer accepts no liability for this!

MAINS OPERATION

1. If necessary, switch off the device using the -knob (11) and remove the battery(ies).
2. Insert the DC hollow plug (16) into the power connection socket (10) on the device.
3.  Insert the C13 plug (17) of the mains cable into the C14 socket (15) on the mains adapter.
4. Insert the plug of the mains power cable into the wall socket.
5. Switch on the device.

TIP: As an alternative to mains operation, the device can also be operated by means of a rechargeable battery (see Chapter 3.2).

BATTERY OPERATION

NOTE This function/use requires optional accessories that are not included in the scope of delivery: rechargeable battery.

1. If necessary, switch off the unit using the -knob (11) and disconnect it from the mains (pull out the mains plug (16)).
2. Insert the suitable battery4 into the battery holder so that it audibly clicks into place.
3. Switch on the device.
4. To remove the rechargeable battery4, switch off the device first . Push the push button for battery fixation completely and remove the battery from the battery holder at the same time.

TIP: As an alternative to battery operation, this device can also be operated using mains voltage (see “Mains voltage”). Chapter 3.1:

LIGHT MODE & ADJUSTMENT

1. Press the control dial (13) for approx. 3 seconds to switch between the continuous light mode and the scene light mode.
2. In continuous light mode, turn the control knob to adjust the light intensity of the dimmer between 10% and 100%.
3. In scene light mode, briefly press the control dial to switch between light intensity, scene light mode (turn the dial to switch between F1 to F6) and flash frequency (turn the dial to switch between 1 to 9).

Explanation of the scene light types:
F1: Paparazzi / F2: Fireworks / F3: Defective lamp
F4: Flash / F5: TV / F6: SOS

SLEWING THE LED LAMP

1. Hold the LED lamp in one hand and simultaneously loosen the fixing screw (6) on the yoke arm with the other hand.
2. Swivel the LED lamp to the desired position and tighten the fixing screw again.

MOUNTING THE LED LAMP ON A STAND

NOTE: This function/use requires optional accessories that are not included in the scope of delivery: Photo tripod with spigot attachment.

1. Unscrew the fixing screw (3) for the tripod connection until the opening of the tripod connection is free.
2. Place the lamp with the tripod connection (4) on the spigot attachment4 of a tripod4 with sufficient load-bearing capacity.
3. Tighten the fixing screw so that the lamp is fixed to the stand without wobbling.

MOUNTING OF ACCESSORIES WITH BOWENS CONNECTION

NOTE: Before mounting accessories on the mounting ring, it is recommended to swivel the LED light and fix it in position so that the LED module points upwards. Only accessories with Bowens connection can be used!

1. Insert the accessory with the existing three “lugs” into the corresponding recesses on the pickup ring (1).
2. Fix the accessory in the pickup ring by turning it slightly to the right or left.
3. For disassembly, first turn the accessory back in the pickup ring and then pull it off.

DISPOSAL
Dispose of the packaging materials by type. Contact your local waste- disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! According to the European Directive 2002/96/EU on Waste Electrical and Electronic Equipment and its transposition into national law, used electrical equipment must be collected separately and recycled in an environmentally sound manner.
Observe the current legal regulations when disposing of the device! Information on proper disposal can be obtained from municipal waste disposal service providers or the Environmental Agency.

CLEANING
Before cleaning the device, disconnect it from the power supply (remove plug or remove batteries)!
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture. Store it in the supplied bag or transportation packaging. The batteries should be removed from the unit if it has not been used for a long time.

EC DECLARATION OF CONFORMITY
“Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. This can be viewed at any time upon request at www.bresser.de/download/SL-LED/CE/SL- LED_CE.pdf

UKCA DECLARATION OF CONFORMITY
“Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. This can be viewed at any time upon request at www.bresser.de/download/SL-LED/UKCA/SL- LED_UKCA.pdf

TECHNICAL DATA

battery’
Battery type°| 2 x NP-F960 Li-Ion| 1 x V-Lock Li-Ion
Dimensions| 30x70cm

1. The LEDs have a long lifetime and are not replaceable due to technical reasons.
2. The power of an LED lighting is higher than that of conventional halogen lights. Therefore, LED’s have a lower wattage than comparable lights.
3. Maximum power when used under mains voltage via mains adapter; in battery operation, the maximum power is reduced by approx. 25% (low power indication)
4. Not included in the scope of delivery / Only use recommended accessories!

GUARANTEE

The regular warranty period is 5 years and begins on the day of purchase. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms.

www.bresser.de/warranty_terms

Please contact the service centre fi rst for any questions regarding the product or claims, preferably by e-mail.
E-Mail: service@bresseruk.com
Telephone: +44 1342 837 098
BRESSER UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom
Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope

© 2021 Bresser GmbH, 46414 Rhede, Germany.
No part of this manual may be reproduced, transmitted, transcribed or translated into any language in any form without the written permission of Bresser GmbH. Errors and technical cahnges reserved.
Manual_F004543-F004544-F004545-F004546_BR-SL_en_BRESSER_v062021a

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>