BRESSER 1877491 Digital Night Vision Binoculars 3,5x Monochrome Instruction Manual
- June 6, 2024
- BRESSER
Table of Contents
BRESSER 1877491 Digital Night Vision Binoculars 3,5x Monochrome
About this Instruction Manual
Please read the safety instructions and the operating instructions carefully
before use.
Keep these instructions for renewed use at a later date. When the device is
sold or given to someo-ne else, the instruction manual must be provided to the
new owner/user of the product.
General Warning
DANGER!
Children should only use the device under adult supervision. Keep packaging
material, like pla-stic bags and rubber bands, out of the reach of children,
as these materials pose a choking hazard.
Do not expose the device to high temperatures. Excessive heat or improper
handling could trig-ger a short-circuit, a fire or an explosion.
FIRE RISK!
Do not place the device, particularly the lenses, in direct sunlight. The
concentration of light could cause a fire.
RISK of ELECTRIC SHOCK!
This device contains electronic components that operate via a power source.
Children should only use the device under adult supervision. Only use the
device as described in the manual; otherwise, you run the risk of an electric
shock.
NOTE!
Do not disassemble the device. In the event of a defect, please contact your
dealer. The dealer will contact the Service Centre and can send the device in
to be repaired, if necessary.
Privacy PROTECTION!
The night vision device is intended only for private use. Please heed the
privacy of other people. Do not use them to look into apartments, for example.
NOTES on Cleaning
Before cleaning the device, disconnect it from the power supply! Only use a
dry cloth to clean the exterior of the device. To avoid damaging the elec-
tronics, do not use any cleaning fluid. Clean the eyepieces and/or lenses only
with a soft, lint-free cloth, (e.g. microfibre cloth). To avoid scratching the
lenses, use only gentle pressure with the cleaning cloth. Protect the device
from dust and moisture.
Scope of delivery
Night vision device, bag, strap, Instruction manual
Do not dispose of electronic devices in the household garbage! As per
Directive 2002/96/EC of the European Parliament on waste electrical and
electronic equipment and its adaptation into German law, used electronic
devices must be collected separately and recycled in an environmentally
friendly manner.
Parts overview
ZOOM
| When in Video or Photo mode: Press ZOOM to zoom in at multiple levels (1.5X, 2X). The maximum zoom is 2X. Once reaching 2X, press ZOOM one ore time to go back to normal.
When in Playback mode: Press the ZOOM button to open the delete menu of the current file.
When in Menu mode: Press the ZOOM to go up.
---|---
IR button| Press IR for 4 levels of brightness (0/1/2/3) when using
the binoculars at night.
When in Playback mode: Press IR to playback the next file.
When in Menu mode: Press IR to go down.
MODE button| • There are 4 modes: Video / Photo / Playback / Menu (in a loop)
• When the power is on, the default mode is video
• Press the mode button to change to the next mode.
SNAP button
| When in Video mode: Press the button to start video recording, press again to stop recording.
When in Photo mode: Press the button to take photos. When in Playback mode: Press the button to playback the selected item.
POWER button| Press and hold for 3 seconds to switch the unit on or
off.
LCD Screen| Look inside the LCD Screen and target the object you would
like to view.
IR FILTER| Protection lid must be taken off for night use.
IR LENS
TRIPOD ADAPTER| Mounting fixture for e.g. a tripod or head mount
(tripod or head mount not included).
BATTERY COVER| 4x AA batteries required
Hooks for carrying strap
Turn on the device
- Press and hold the POWER button (9) for 3 seconds to turn on the binoculars. Once the pow-er is on, look into the LCD screen inside.
- Target the object you would like to view and adjust the focus by turning the focus wheel (1).
- For night use, turn on the IR by pressing the IR button (6). Increase the brightness by pressing the button repeatedly. It has 4 levels of brightness (0/1/2/3)
- Long press the POWER button (9) to shut down the device.
Capturing a video
- When the power is on, the night vision device starts automatically in the video mode.
- If the video Mode icon is not showing, press the MODE button multiple times until the icon shows up.
- Adjust the focus by turning the focus wheel.
- During low light conditions or at night, adjust the brightness by pressing IR.
- Press the SNAP button to start recording videos. Press the button again to stop the recording.
Capturing a photo
- Press the MODE button until you enter the Photo Mode.
- If the camera Mode icon is not showing, press the MODE button multiple times until the icon shows up.
- Adjust the focus by turning the focus wheel.
- During low light conditions or at night, adjust the brightness by pressing IR.
- Press the SNAP button to take pictures.
Playback
- Press the MODE button until you enter the Playback Mode.
- The LCD screen will show the last file saved. If the file was a photo it will show, if it was a video it will show.
- Press the IR button to go to the next file.
- Press the SNAP button to playback the video file.
- Press the ZOOM button to open the delete menu for the currently selected file. Press IR to go down or ZOOM to go up. Press SNAP to confirm.
Display Information
Menu Settings
You can make changes to settings in the Menu mode. Press the MODE button several times until you are in the Menu mode. Press the IR button to go down the menu, or press the ZOOM button to go up. Press the SNAP button to enter. Once the desired setting is selected, press the SNAP button again to save it. Press the MODE button to exit back to Video Mode.
Format
- Yes To delete all the files on the microSD/TF card
- No Cancel format
Auto Power Off
- 1Minute Auto power off in 1 minute without action
- 3Minutes Auto power off in 3 mins without action
- 5Minutes Auto power off in 5 mins without action
- No No auto power off (Default setting)
TV Mode
The video output mode can be set to NTSC (North America) or PAL (Europe)
- 50 Hz The default setting for EU
- 60 Hz Default setting for U.S. and Japan
- Backlight To select the brightness level of the LCD screen 4 levels of brightness (1/2/3/4).
- Language Select one of the available languages
- Date/Time Select Date/Time on or off. Set the Date and Time (YY/MM/DD)
- Version Display firmware version
Troubleshooting
Poor Image:
• If you wear reading glasses or varifocals, make sure you keep a minimum
distance of 20-30 cm from the screen.
• If at day, make sure the protection lid is on. If at night, make sure the
protection lid is off.
• Adjust the focus by slowing turning the Focus wheel at the front bottom of
the binocular. Make sure it is focused.
Contact
Bresser GmbH Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope
Bresser UK Ltd.
Suite 3G, Eden House Enterprise Way, Edenbridge, Kent TN8 6Hf, Great Britain