ANKER A2562 PowerWave Magnetic Pad Slim Instructions
- June 6, 2024
- Anker
Table of Contents
PowerWave Magnetic Pad Slim
Instructions
For FAQs and more information, please visit:
anker.com/support
- You cannot charge your device wirelessly when using an ultra-thick (>4 mm) protective phone case or a case with a pop socket. · This wireless charger only supports the protective cases that match the magnetic structure of the iPhone.
- Do not place any foreign objects between your device and the wireless charger’s surface, including metal pads on a car mount, magnetic cards, door keys, coins, metal objects, or NFC cards, as they could potentially demagnetize the wireless charger, affect the charging speed, or cause overheating.
- Wireless chargers make charging more convenient than wired chargers but confined by current wireless technology, their charging speed is slower than that of wired chargers.
- High temperatures will reduce charging speed and restrict power. It is recommended that you charge your device in environments with temperatures below 35°C / 95°F.
Important Safety Instructions
Please refer to the electrical and safety information on the bottom before installing or operating the product.
- Avoid dropping.
- Do not disassemble.
- Do not expose to liquids.
- For the safest and fastest charge, use original or certified cables.
- This product is suitable for moderate climates only.
- The maximum ambient temperature during the use of this product must not exceed 40°C.
- Open flame sources, such as candles, must not be placed on this product.
- Only use a dry cloth or brush to clean this product.
- The socket outlet shall be installed near the product and shall be easily accessible.
- Disconnection from line voltage should be made via the AC plug.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Product Name: PowerWave Magnetic Pad Slim
Model: A2562
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1 800 988 7973
I C Statement
This device complies with RSS-216 of Industry Canada. Operation is subject to
the condition that this device does not cause harmful interference.
RSS-Gen Issue 5
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment
RF exposure statement:
The equipment complies with the IC Radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
This device was tested for operations. To comply with RF exposure
requirements, a minimum separation distance of 20cm must be maintained between
the user’s body and the handset, including the antenna. Third-party belt
clips, holsters, and similar accessories used by this device should not
contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna.
This device in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. All essential radio test suites have been
carried out.
1. The device complies with RF specifications when the device is used at 20cm
from your body
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2562 is in
compliance with Directives 2014/53/EU & 2011/65/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://www.anker.com/
UK Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2562 is in
compliance with the following Directives: Radio Equipment Regulations 2017,
Electrical Equipment (Safety) Regulations 2016, and The Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012. The full text of the UK declaration of conformity is
available at the following internet address:
https://www.anker.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
Anker Technology (UK) Ltd Suite B, Fairgate House, 205 Kings Road, Tyseley,
Birmingham, B11 2AA, United Kingdom
This device was tested for operations. To comply with RF exposure
requirements, a minimum separation distance of 20cm must be maintained between
the user’s body and the handset, including the antenna. Third-party belt
clips, holsters, and similar accessories used by this device should not
contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna. This device is in
compliance with the essential requirements and other relevant provisions of
the UKCA. All essential radio test suites have been carried out.
1. The device complies with RF specifications when the device is used at 20cm
from your body.
Specifications
Input | 5V 2.4A / 9V 2A |
---|---|
Output | 5W / 7.5W / 10W |
Operating Temperature | -10° C to 40° C |
Radiated H-Field | -48.081dBuA/m (@10m) |
TX/RX Frequency Range | 110-205kHz (Only for EU and UK) |
Indoor use only. | |
--- | --- |
This symbol indicates that this product shall not be treated as household |
waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
: Lifetime technical support
support@anker.com
support.mea@anker.com (For the Middle East
and Africa Only)
(US) +1 (800) 988 7973 Mon-Fri 9:00am – 5:00pm (PT)
(UK) +44 (0) 1604 936200 Mon-Fri 6:00 – 11:00 (GMT)
@anker_official
@anker_jp
@Anker Deutschland
@Anker Japan
@Anker
@AnkerOcial
@Anker_JP