Funclass OSTIALITE TWS Earphone User Guide
- June 6, 2024
- Funclass
Table of Contents
Initiate TWS Pairing
- If both earphones have never been paired, the earphones will initiate TWS pairing mode right after earphones are removed from the charging case.
- Touch and hold both MFB buttons of earphones for 5 seconds to initiate pairing mode when the earphones are turned off.
Power On/Off
- Turn on/off the earphones by touching and holding MFB buttons for each earphone for 3 seconds.
- Remove the earphones from the charging case, they will automatically be turned on and connected to your device. The earphones will automatically turn off when putting the earphones back into the charging case
OSTIA Lite Control
**** When pairing with each earbud only
**** when connected with the product
Basic Function
Power on
- Turn on earphones by touching and holding MFB buttons for each earphone for 3 seconds.
- Remove the earphones from the charging case, they will automatically be turned on and connected to your device.
Power off
- Turn off earphones by touching and holding MFB buttons for each earphone for 3 seconds.
- The earphones will automatically turn off when putting the earphones back Into the charging case.
TWS reconnection
If you have already initiated pairing mode, It will automatically reconnect to
your device.
Auto power off
- If there’s no connection with the device for 2 minutes, the earphones will be turned off.
- The power will be turned off after 2 minutes when there’s no operation after disconnecting the earphones.
Reset earbuds
Take the earbuds out from the charging case and touch both earbuds for 2secs
to turn them off (Red LED lights on)
After the power is off for both earbuds, touch both earbuds for more than
lOsecs (White LED > After White and Red LED lights goes on/off) When the LED
lights off-take hands off from the touchpads and put them into the charging
case
Call
Answer calls
Touch the MFB button to answer incoming calls.
Refuse calls
Double touch the MFB button to reject calls.
Hang up
When the call is finished, a single touch of the MFB button ends the call.
Answer Incoming Call After Hanging Up the Current Call
If there is a new incoming call during the call, single touch of the MFB
button to hang up the current call and single touch of the MFB button again to
answer the new incoming call.
*This function requires mobile phone/wireless earner support
Answer Call After Call Waiting
If there is a new incoming call during the call, long touch of the MFB button
to make the current call waft and a single touch of the MFB button again to
answer the new incoming call.
*This function requires mobile phone/wireless carrier support
Call Forwarding
If there are two callers in line, one in the current call, one waiting, long
touch of the MFB button to make the current call to forward to another call.
*This function requires mobile phone/wireless carrier support
Accessories
- OSTIA
- Charging Case
- Silicone Eartips
- Mesh
- Please check the ‘DIVINUS’ youtube channel for How to use Sound Filters. 5. USB Type-C Charging Cable 6. Manual
Device Layout
FCC Requirement
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>