DoorBird Multi Dwelling IP Intercom Video Door Station Instruction Manual
- June 6, 2024
- DoorBird
Table of Contents
Multi Dwelling IP Intercom Video Door Station
INSTALLATION MANUAL
Hazard information
Read these instructions carefully before starting to use any components. Keep
the manual so you can refer to it at a later date if required. If you hand
over the device to other persons for use, please hand over the operating
manual as well.
You can always find the most up-to-date version of the installation manual on
www.doorbird.com/support To make things easier we use the term “device” for
the product “IP Video Door Station D11x series” and “mobile device” for a
smartphone or tablet.
Liability Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions. Bird
Home Automation GmbH cannot be held responsible for any technical or
typographical errors and reserves the right to make changes to the product and
manuals without prior notice. Bird Home Automation GmbH makes no warranty of
any kind with regard to the content of this document, including, but not
limited to, the implied warranties of merchantability and fitness for a
particular purpose. Bird Home Automation GmbH shall neither be liable nor
responsible for incidental or consequential damages in connection with the
furnishing, performance or use of this material. This product is only to be
used for its intended purpose.
Equipment Modifications This equipment must be installed and used in strict
accordance with the instructions given in the user documentation. This
equipment contains no components that require service by the user.
Unauthorized equipment changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Symbols used
Danger: Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Warning: Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
Caution: Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.
NOTICE Notice: Indicates a situation which, if not avoided, could result in
damage to property.
Important: Indicates significant information which is essential for the
product to function correctly.
Note: Indicates useful information which helps in getting the most out of the
product.
2
WARNING
· Mounting, installation and servicing work on electrical devices may only be
performed by a qualified eletrician. Failure to observe this regulation could
result in the risk of serious damage to health or fatal injury due to electric
shocks.
· Devices with 110-240 V connection: The device may only be connected to an
easily accessible power socket outlet. The mains adapter must be pulled out if
a hazard occurs.
· For power supply, only use the original plugin mains adapter delivered with
the device or a recommended PoE-Switch/PoE-Injector as specified in this
manual.
· Because of electrostatic charging, direct contact with the circuit board can
result in destruction of the device. Direct contact with the circuit board
must therefore be avoided at any time.
· Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
· Do not use the device if there are signs of damage to the housing, control
elements or connecting sockets, for example, or if it demonstrates a
malfunction. If you have any doubts, please have the device checked by an
authorized expert.
· Do not open the device. This voids the warranty of the device. The device
does not contain any parts that can be maintained by the user. In the event of
an error, please have the device checked by an authorized expert. · For
safety, approval and licensing reasons (CE/ FCC/IC etc.), unauthorized change
and/or modification of the device is not permitted.
· The device is not a toy; do not allow children to play with it. Do not leave
packaging material lying around. Plastic films/bags, pieces of polystyrene,
etc. can be dangerous in the hands of a child.
· Always lay cables in such a way that they do not become a risk to people and
domestic animals.
· Voltage is applied to parts within the equipment. Do not touch any parts
that are not associated with the installation, wiring, or connection. Electric
shock could result.
· On devices which are not marked as weatherproof: Keep the device away from
water or any other liquid.
· Do not install or make any wire terminations while power supply is plugged
in. It can cause eletric shock or damage to the device.
· Before turning on power, make sure wires are not crossed or shorted. If not,
fire or eletric
WARNING
shock could result.
· High voltage may be present internally. Do not open the device. Electric
shock could result.
· The device is not of explosion-proof. Do not install or use near gases or
flammable materials. Fire or explosion could result.
· Do not install two power supplies in parallel to a single input. Fire or
damage to the device could result. Be sure to connect a single power supply to
the device.
· Do not connect any terminal on the device to an AC power line. Fire or
electric shock could result.
· Keep AC cord from being marred or crushed. If the AC cord is fractured, fire
or electric shock could result.
· Do not plug or unplug with wet hands. Electric shock could result.
· Do not put any metal or flammable material into the device. Fire, electric
shock, or device trouble could result.
· Existing wiring may contain high voltage AC electricity. Damage to the
device or electric shock could result. Wiring and installation must be done by
a qualified eletrician.
· When mounting the device on a wall or ceiling, install the device in a
convenient location, but not where it could be jarred or bumped. Injury could
result.
· On devices with ground terminals, connect to an earth ground. Otherwise fire
or malfunction could result.
· On devices with plastic or real glass, do not put high pressure on the
glass. If fractured, injury could result.
· On devices with LCD, if LCD is punctured, do not allow contact with the
liquid crystal inside. Injury could result. If necessary, gargle your mouth
and clean your eyes or skin with clear water for at least 15 minutes and
consult your doctor.
· Do not put anything on the device or cover the device with cloth, silicone,
glue, coating, separate covering etc. Fire or device issues could result.
· Do not install the device in any of the following locations. Fire, electric
shock, or device trouble could result.
Places under direct sunlight or places near heating equipment that varies in
temperature.
Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).
Places subject to moisture and humidity extremes, such as bathrooms, cellars,
greenhouses, etc.
Places where the temperature is very low, such as inside a refrigerated area
or in front of an air conditioner.
Places subject to steam or smoke (e.g. near heating or cooking surfaces).
Where noise generating devices such as dimmer switches or inverter electrical
appliances are closeby.
Locations subject to frequent vibration or impact. · On devices with intercom,
be sure to perform a call test with low audio volume on both intercom devices.
A sudden call etc. may arrive causing for example damage to your ear.
· If the device does not operate properly, unplug the power supply.
· All devices which are not marked as weatherproof are designed for indoor use
only. Do not use outdoor.
· On devices which are marked weather-proof: Do not spray with high-pressure
water. Device issues could result.
· We do not assume any liability for damage to property or personal injury
caused by improper use or the failure to observe the
· hazard information. In such cases, any claim under warranty ceases. For
consequential damages, we assume no liability!
Safety instructions
NOTICE · The device shall be used in compliance with local laws and
regulations.
· Store the device in a dry and ventilated environment.
· Avoid exposing the device to shocks or heavy pressure.
· Do not install the device on unstable brackets, surfaces or walls. Make sure
the material is strong enough to support the weight of the device.
· Use only applicable tools when installing the device. Using excessive force
with tools could cause damage to the device.
· Do not use chemicals, caustic agents, or aerosol cleaners.
· Use a clean dry cloth for cleaning.
· Use only accessories that comply with technical specification of the device.
These can be provided by Bird Home Automation GmbH.
· Use only spare parts provided by or recommended by Bird Home Automation
GmbH.
· Do not attempt to repair the device by yourself. Contact Bird Home
Automation GmbH for service matters.
3
ENGLISH
· Keep the device more than 1 m (3.3) away from microwave, radio, TV, wireless router and any other wireless devices. · On devices with intercom or built-in speaker or built-in microphone or signal transmission functions, keep the wires more than 30 cm (12“) away from AC 100-240 V wiring. AC induced noise and/or device malfunction could result. · Install the device in an area that will be accessible for future inspections, repairs and maintenance. · If the device is used close to a cellular phone, the device may malfunction. · The device can be damaged if dropped. Handle with care. · The device turns inoperative during power failure. · On devices with intercom or built-in speaker or built-in microphone, in areas where cellular or Radio / TV broadcasting station antennas are closeby, the device may be affected by radio frequency interference. · On devices with LCD screen, it must be noted in advance that the LCD panel, though manufactured with very high precision techniques, inevitably will have a very small portion of its picture elements always lit or not lit at all. This is not considered a device malfunction. · On devices with intercom, due to the environmental sound around the device, it may hinder smooth communication, but this is not a malfunction. · On devices with Username/Password, the Username/Password to access the device is the customer
s responsibility. Make sure to use a password that
cannot be easily guessed by a third party. We recommend that you change the
Password on a regular basis.
· We will, under no circumstances, be liable for damage that occurs due to
failures in power supply, network equipment or terminal devices; failures due
to Internet providers and cellular network providers; failures such as
disconnected lines and other losses in communication, which makes it
impossible to provide this service as well as in any way delay this service
due to any other causes outside of our responsibility; or if an error or
missing data occurs during transmission.
Information on disposal for users of waste electrical & electronic equipment
(private household)
This symbol on the products and/or accompanying documents means that used
electrical and electronic products should not be mixed with general household
waste. For proper treatment, recovery and recycling, please take these
products to designated collection points, where they will be accepted an a
free of charge basis. Alternatively, in some countries you may be able to
return your products to your local retailer upon the purchase of an equivalent
new product. Disposing of this product correctly will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest
designated collection point. Penalties may be applicable for incorrect
disposal of this waste, in accordance with national legislation.
Information on disposal in other countries outside the European Union
This symbol is only valid in the European Union. If you wish to discard this
product, please contact your local authorities or dealer and ask for the
correct method of disposal.
Transportation
When transporting the device, use the original NOTICE
packaging or equivalent to prevent damage to the device.
Warranty Information
For information about the device warranty, see www.doorbird.com/warranty
4
ENGLISH
COMPONENTS*
THIS SIDE UP
1x Main Electrical Unit with call button(s) and front panel
1x Back-housing with
1x Installation manual
wall-mounting bracket
1x Quickstart guide with Digital Passport
1x Drilling template
1x Waterproof A4 laser printer paper for labelling name plates
1x Power supply unit (mains adaptor) with four country-specific adaptors
1x RJ45 Adapter
1x Screw connection terminal plug
Small parts
- The sketches in this manual may differ from the purchased model.
DEVICE WITH CALL BUTTON
Front 1
2
WIFI
6 3
4
7
8 5
9
Inside
10 11 12 13
THIS SIDE UP
14
-
Front panel 2) HDTV Video 3) Security screws 4) Light Sensor
For night-vision mode 5) Bluetooth transceiver 6) Speaker 7) Microphone 8) 4D Motion sensor 9) Illuminated call button with nameplate -
Diagnostic-LED Lights up a few seconds after connecting the device to power
-
Main Electrical Unit 12) Screw connection terminal 13) Gasket 14) Housing with wall-mounting bracket
The flush-mounted model may differ optically. 5
DEVICE WITH CALL BUTTONS
Front 1
2
WIFI
6 3
4
7
8 5
9
10
Inside
11 12 13 14
THIS SIDE UP
15
-
Front panel 2) HDTV Video 3) Security screws 4) Light Sensor
For night-vision mode 5) Bluetooth tranceiver 6) Speaker 7) Microphone 8) 4D Motion sensor 9) First illuminated call button with nameplate 10) Second illuminated call button with nameplate -
Diagnostic-LED Lights up a few seconds after connecting the device to power
-
Main Electrical Unit 13) Screw connection terminal 14) Gasket 15) Housing with wall-mounting bracket
The flush-mounted model may differ optically.
DEVICE WITH KEYPAD MODULE
Front
Inside
1
NO WIFI
16
2
9
3
11
4
12
5 10
14
6
7
15
8
13
-
Front panel 2) HDTV Video 3) Speaker 4) Security screws 5) Light Sensor
For night-vision mode 6) Microphone 7) Bluetooth tranceiver 8) 4D Motion sensor 9) Keypad Module
The illumination is also acting as Diagnostic LED(s) 10) Illuminated modern call button (with nameplate) or illuminated classic call button (round) 6 -
Main Electrical Unit 12) Diagnostic-LED
Lights up a few seconds after connecting the device to power 13) Gasket 14) Screw connection terminal 15) Holder for 2-Wire Ethernet PoE Converter A1071 (optional) 16) Housing with wall-mounting bracket
The flush-mounted model may differ optically.
ENGLISH
VIDEOS
SWITCHING OFF POWER
Need help with the installation? Be sure to watch our installation videos
which can be found on http://www.doorbird.com/support
Each individual step of the installation is clearly documented in the videos.
INSTALLATION
All the steps below should be carried out carefully by a competent adult,
taking into consideration any applicable safety regulations. Please contact us
directly or seek the advice of a competent specialist.
Please ensure that all wires used for the installation are undamaged along
their entire length and approved for this type of use.
Network speed and network components Please ensure that the upload speed of
your Internet connection is at least 0.5 Mbps. The user experience is only as
good as your network speed, network stability and quality of your network
components, such as your Internet Router and WiFi access points or WiFi
repeaters. Please also make sure that your network components are no older
than two years old, have been manufactured by a well-known manufacturer, and
have the latest firmware installed.
Switch off the power to all wires leading to the assembly location, i.e. the
door chime, electric door opener, power supply unit for the video door station
etc.
DISMANTLING THE EXISTING DOORBELL
Should there already be a doorbell or door station on the exterior wall of the
house, please remove it.
DETERMINING THE ASSEMBLY LOCATION
The device uses an ultra wide-angle hemispheric lens so that even when the
person is a minimum distance of 50 cm (19.68 in) away from the device, a low
installation height is sufficient. The lens is therefore not mechanically
adjustable. The camera lens should be located at an altitude of at least 145
cm (57 in). You may check this prior to the final mounting.
Should these requirements not be fulfilled, it may occur, for example that the performance of audio and video is poor or push notifications are delayed or do not arrive on your smartphone or tablet at all.
Requirements: High-speed Internet (via landline): DSL, cable or optical fibre Network: Ethernet, with DHCP
145 cm 57 in
130 cm 51.18 in
7
Only for D1101V & D1102V We offer additional wall-mounting kits for D1101V and D1102V Surface-Mount with a wedge corner wall-mount adapter (7.5° vertical down or up) and alternatively an angle corner wall-mount adapter (45° horizontal, mounts left or right).
ASSEMBLING THE MOUNTING HOUSING
The product is available as a surface-mounted and flush-mounted version. In
the flush-mounted version, the front panel is slightly larger to better cover
the hole in the wall and the mounting housing (backbox) is made entirely of
metal instead of plastic.
If you use the flush-mounted housing, lever up the wall accordingly.
A8001 Wedge corner wall-mount adapter (7.5°, mounts vertical down or up), sold separately
A8002 Angle corner wall-mount adapter (45° horizontal, mounts left or right), sold separately
When choosing the assembly location, consider the lighting conditions. Avoid
direct sunlight, direct backlight and reflective surfaces.
Do not expose the device to direct sunlight. NOTICE The housing temperature
can exceed the
maximum allowed temperature limit. This can result in damage of electric and
mechanic components of the device and injuries especially when touching
exterior parts of the device. White and bright silvercolored front plates
absorb less sunlight than dark ones.
If the wall of the house is not made of wood, you should drill dowel holes 5
mm (0.19 in) in diameter in the wall according to the drilling template and
then place the dowels provided into the boreholes.
If you must drill holes in a wall, insert screws into a wall or lever up a
wall, ensure that no cables or mains (gas, water, etc.) are to be found in the
wall.
An image sensor must not be exposed to NOTICE direct sunlight for an extended
period of
time. Direct sunlight will “blind” the camera and may permanently bleach the
small color filters on the image sensor chip.
Any defects caused by direct sunlight are not covered by warranty.
If the wall of the house is made of wood, dowels are not normally required. There are special dowels for assembling the device on an insulating wall, e.g. Fischer insulating dowels.
8
ENGLISH
. ASSEMBLING THE FRONT PANEL
Remove the front panel with the attached Main Electrical Unit carefully from
the mounting housing (backbox) using the screw driver provided.
We have designed the front panel and safety screws in a way that they cannot
be screwed through the front panel so that they do not fall off / get lost
during installation.
D1101V
D1102V
Turn the safety screws counter-clockwise until they are loose.
D1101KH
Turn the safety screws counter-clockwise until they are loose.
Pull the front panel with attached Main Electrical Unit out of the mounting housing (backbox).
Pull down the front panel.
Pull the front panel with attached Main Electrical Unit out of the mounting housing (backbox).
. MOUNTING
Lead all cables and wires you want to connect to the device through the
mounting housing.
Flush-mounted models
Surface-mounted models
Before mounting: Pierce through the middle of the rubber seal for the cable
entry using a screwdriver.
9
Screw the wall-mounting bracket of the mounting housing to the wall.
Flush-mounted models
Surface-mounted models
Please make sure that the outer frame of the flushmounted housing rests on the outside of the wall and that the edge of the flush-mounted housing is sealed all around against moisture from the outside.
NETWORK CONNECTION OPTIONS
You can connect the device to the network by either using a WiFi 2.4 GHz
connection (only for D1101V and D1102V) or a network cable.
OPTION
Network cable (recommended, maintenance free)
Install a network cable (which is plugged into a network switch / router with
Internet access) from the inside of your building to the assembly location.
The network cable between the assembly location and the network switch /
router can have a maximum length of 80 m/262 ft (IEEE 802.3). If you must span
a distance of more than 80 meters/262 feet you can put a network switch in
between.
If you have only two wires available at the assembly location, you may use the
“DoorBird 2-Wire Ethernet PoE Converter A1071”, sold separately. It allows you
to transfer network data (Ethernet) and power (PoE) with a simple two-wire
cable over long distances. For example, existing buildings with a simple two-
wire bell wire can be equipped with network technology without having to
retrofit any network cables.
OPTION
WiFI 2.4 GHz (only for D1101V and D1102V)
For reasons of network stability, we principally recommend using a network
cable, as WiFi is sensitive to interference (range, house walls acting as
shields, reliability of performance, third party WiFi networks, wireless
transmitters causing interference in the area, etc.).
When using WiFi please make sure you have a good WiFi signal at the assembly
location of the device. You can increase the WiFi signal by using so called
“WiFi repeaters”, which can boost your WiFi signal. You should install such a
WiFi repeater close to the assembly location of the device, typically inside
your home and close to the device.
10
ENGLISH
PREPARE POWER SUPPLY
The device does not have a battery as power supply, therefore, choose one of
the following options.
OPTION
Power supply using the power supply unit (mains adaptor)
To power the device using the provided mains adapter, 2 insulated wires are
required. The power supply unit has a 300 cm (9.8 ft) long cable with two
insulated wires. The network connection is then established via a network
cable or alternatively via WiFi.
The provided mains adaptor is only capable to power one device. It is not
designed to power multiple devices simultanously.
If you must power more than one device with one power supply, we recommend to
use a PoE-Switch with PoE Standard IEEE 802.3af Mode A or an appropriate DIN
rail power supply (see “OPTION 3”).
Do not plug the power supply unit into the NOTICE wall socket yet.
Only use the power supply unit provided along with the device, or a DIN-rail
power supply unit (see “OPTION 3”) that you can obtain from us separately,
since this has been specially stabilized electrically and is equipped with an
integrated audio interference reduction device. Other power supply units may
destroy the device or cause poor transmission quality. The warranty
automatically expires if you use a different power supply unit.
The power supply unit is plugged into a wall socket inside your house (Step
10), usually where the two wires from your assembly location come out of the
wall in the interior of the house.
The provided mains adapter is not outdoorready, it is for indoor-use only.
OPTION
Power supply and network connection using PoE (Power over Ethernet)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector
(e.g. DoorBird Gigabit PoE Injector A1091), use a CAT.5 cable or higher in
accordance with the PoE standard IEEE 802.3af Mode A.
A CAT.5 cable or higher must be used for this purpose, as network signals can
only be transmitted over completely insulated, shielded and twisted cables. If
you use PoE as a source of power, the four wires for PoE then simultaneously
form the data line. The device will not start if your PoE-Switch/ PoE-Injector
does not support the PoE Standard IEEE 802.3af Mode A.
If you must power more than one device with one power supply , we recommend to
use a PoE-Switch with PoE Standard IEEE 802.3af Mode A or an appropriate DIN
rail power supply (see “OPTION 3”).
Theoretically (not recommended by us!), an unshielded, but over the whole
length (max. 80 m/262 ft) twisted bell wire with two pairs of wires (first
twisted pair of wires: “T+, T-“, second twisted pair of wires “R+, R-“) can be
used for the network and PoE transmission as an alternative to a Cat.5 network
cable or better. This is comparable to a Cat.3 network cable. In this case,
however, we cannot guarantee the data throughput or the stability of the
network connection and power supply; this must be measured and checked on site
by qualified personnel over several hours (network data is transmitted at high
frequency, therefore a shielded Cat.5 network cable twisted in pairs or better
must normally be used).
Do not combine the power supply from the NOTICE power supply unit (mains
adaptor) with the
power supply via PoE.
You can find further information about PoE here: http://www.doorbird.com/poe
1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.
11
OPTION
Power supply using a DIN rail power supply unit
Alternatively to the mains adapter, we offer DIN rail power supplies in our
online shop, which can be installed by a specialist. The network connection is
then made via a network cable or alternatively via WiFi.
If you must power more than one device with one power supply, we recommend to use a PoE-Switch with PoE Standard IEEE 802.3af Mode A or an appropriate DIN rail power supply.
CONNECTING THE DEVICE
It is possible to connect the cables and wires to the device conveniently and
safely via the labeled screw connection terminal. You can connect all
necessary cables and wires to the device now.
For easier installation we strongly recommend to remove the plug from screw
connection terminal while you connect the cables and wires.
NOTICE Please remove any cables and wires from the connection ports of the
device that you do not need.
LAN/POE
T+ T- R+ R-
Max 24V 1 A
R R
Max 0V 0 A (NO)
E E
COM
15VDC CB
1 A
CB V- V+
12
Port LAN/POE
R1, R1
R1 R1
E1, E1 15 VDC 15 VDC +
Description
The device does not have an integrated standarized RJ45 socket to ensure … ·
that the device rests as flat as possible on the wall. · that no wall needs to
be levered up. · that a strong and inflexible Cat.6 or Cat.7 installation
cable can be used.
Use only four wires (1, 2, 3 and 6) of a standard Network cable Cat.5 or
better, coming from the Internet Router/PoE-Switch/PoE-Injector.
Cat.5 / Cat.6 Network cable T+ White and orange network cable wire (Number 1,
Transmit Data +) T – Orange network cable wire (Number 2, Transmit Data -) R+
White and green network cable wire (Number 3, Receive Data +) R – Green
network cable wire (Number 6, Receive Data -)
Cat.7 Network cable (Installation cable) T+ White network cable wire from pair
“orange/white” (Number 1, Transmit Data +) T- Orange network cable wire from
pair “orange/white” (Number 2, Transmit Data -) R+ White network cable wire
from pair “green/white” (Number 3, Receive Data +) R- Green network cable wire
from pair “green/white” (Number 6, Receive Data -)
NOTICE Do not power the device simultaneously via the power supply from the
power supply unit (mains adaptor) and the power supply via PoE.
Bi-stable latching relay #1, max. 24 V DC/AC, 1 A. Security feature: The relay
keeps its state even in the case of loss of power. You can configure the
default state of the relay (open/close) via the DoorBird App. These ports can
be used to connect e.g. an electric door opener. The device does not supply
power to the connected device. The power supply for the electric door opener
must be installed separately.
When wiring an electric door opener directly to a door station, there is a
risk that the electric door opener could be tampered by unauthorized third
parties (e. g. by breaking the door station and short-circuiting the wiring of
the door opener). Therefore, we generally recommend the use of a remote safety
relay mounted indoors (e. g. DoorBird I/O Door Controller A1081) for wiring an
electric door opener for a more secure installation in your home.
Digital input (0 V, 0 A (NO)), for door opener button, max. 0 V DC/AC, 0 A.
These ports can be used to connect e.g. a door opener button inside the home.
It will can trigger the bi-stable latching relay of the device (R1, R1)
NOTICE Please make sure to add no voltage on these ports. Extra voltage may
destroy the device immediately.
15 V DC Power supply input, negative pole (-). Please connect the black wire
of the power supply unit (mains adaptor) supplied with this device if you do
not power the device using PoE.
NOTICE Do not power the device simultaneously via the power supply from the
power supply unit (mains adaptor) and the power supply via PoE.
15 V DC Power supply input, positive pole (+). Please connect the red wire of
the power supply unit (mains adaptor) supplied with the device here, if you do
not power the device using PoE.
NOTICE Do not power the device simultaneously via the power supply from the
power supply unit (mains adaptor) and the power supply via PoE.
13
ENGLISH
COM1
CB2 CB1
Jack for authorized peripherals of Bird Home Automation which will be released
in the future, e.g. keypad Jack for second call button.
Jack for first call button.
NOTICE The jacks “CB1”, “CB2” and “COM1” on the rear side of the Main Electrical Unit must only be used to connect components certified by Bird Home Automation.
CALL BUTTON PORT
SWITCH (4 PIN)
Use the four wire call-button cable provided to connect the call-button to the Main Electrical Unit (already connected in delivery condition to the jack “CB1″/ “CB2”).
Please take care when connecting the cables and wires. Connecting the cables
and wires the wrong way NOTICE may damage the device. Wires without insolation
material must not protrude out of the green screw
connection terminal, it may lead to electrical short and damage the device.
ASSEMBLE THE DEVICE TO THE MOUNTNG HOUSING (BACKBOX)
Assemble the front panel with the attached Main Eletrical Unit carefully using the screwdriver provided to the mounting housing.
D1101V
D1102V
D1101KH
Turn the safety screws clockwise until they are firmly tightened. Tighten the
safety screws by hand only (less than 5 newton meter [Nm]), otherwise the Main
Eletrical
NOTICE Unit housing may be damaged. If any of the black foam rubber gasket
under the front panel protrudes, you can carefully press it in with the
triangle tool provided in the small parts bag. Please do not press too hard,
so that the gasket is not pressed too far into the inside of the housing and
the unit will have a leak.
14
ENGLISH
ACTIVATE THE DEVICE
DIAGNOSTIC-SOUNDS
If the device is to be supplied with power by a mains adapter, plug the power
adapter of the device into a wall socket. If the device is to be powered via
PoE, switch on the PoE-Switch/ PoE-Injector which is connected to the device.
If the device is to be powered via DIN-rail power supply, switch on the DIN-
rail power supply.
The Diagnostic-LED indicates whether the device is supplied with power. This
LED lights up in green color a few seconds after you have connected the device
to the power supply. The device is now ready for operation.
If the Diagnostic LED does not light up, please check the power supply. When
using a wall-plug power supply and not PoE please check whether you have
connected the positive pole and negative pole to the device correctly.
The device is ready for operation (booting up process, any software updates,
etc.) once it has emitted a short diagnosis sound from the integrated
loudspeaker. This may last for up to 5 minutes.
DOWNLOADING AND INSTALLING THE APP
Download the “DoorBird” App by Bird Home Automation onto your mobile device
from the Apple App Store or Google Play Store. You can always find the most
up-to-date version of the App manual on www.doorbird.com/support
If you use WiFi for connecting the device to your Internet Router, first go to
the DoorBird App > “WiFi Setup” and follow the instructions.
If you have finished the WiFi setup or have connected the device to your
Internet Router by means of a network cable, go to the DoorBird App > “Add
device” and click on the QR code icon in the “User” field. Scan the user QR
code found on the “Digital Passport” provided with the device.
If you have problems adding the device to the App please check if the device
is online ( www.doorbird. com/checkonline ). If the device is not online,
please check the WiFi or network cable connection again.
After around one minute, the device emits brief diagnostic sounds after it has
been connected to power supply / network / internet.
LENS
The product uses a straightened Wide-Eye hemispheric lens (HD). Due to the
wide angle of coverage (horizontal, vertical, diagonal), a small edge may
appear in the corners of the image as well as reflections in the image from
the surface of the front of the unit.
MOTION SENSOR
The device has a built-in Motion Sensor with 4D Technology. You can use it for
numerous applications, e. g. to send an alarm to a mobile device or to switch
a relay to turn on an outdoor light.
The adjustable distance is optimized for a 1.75m (69 in) tall 70kg (165 lbs)
person in a free environment. The accuracy of the distance of the motion
sensor can vary depending on the environment.
BLUETOOTH TRANSCEIVER
The device has a built-in Bluetooth® transceiver. We will add further
functionality for interesting applications soon. Please check our company news
blog or the latest version of this manual at www.doorbird.com/support for
updates.
API
The device features a well documented API for third-party integration. For
information, terms and conditions see www.doorbird.com/api
DOORBIRD CONNECT
The device features many options to integrate it into third-party
applications. For information, terms and conditions see
www.doorbird.com/connect
DIAGNOSTIC-LED
You can see if the device is powered by checking the Diagnostic LEDs, which lights up a few seconds after the power is connected.
The Diagnostic-LED is designed to illuminate only slightly.
15
CHANGING THE LABEL OF A CALL BUTTON NAMEPLATE
Applies only to devices with 1 and more illuminated call buttons with
nameplate.
used roads. Please remove ferrous deposits immediately, as they will attack your door station and lead to real rust if not removed. To remove rust, simply wipe off the dust; in addition, a care product is recommended, e.g. WD 40, available e.g. at Amazon for less than 5.00. Simply apply in a thin layer and rub in. The same applies if rust appears on the engravings on the stainless steel surface.
Cement or lime splashes should be carefully removed as soon as possible with a wooden spatula before hardening.
The following cleaning detergents are not to be used as they reduce corrosion
resistance: · products containing chloride and hydrochloric
acid · Bleach (in case of accidental use, rinse thoroughly
with water) · Silver polish
MAINTENANCE OF THE FRONT PANEL
Cleaning and maintenance instructions All of our front panels are made of
high-quality materials and are designed for a durable lifetime. Since door
stations are usually installed in unprotected outdoor areas, they are exposed
to adverse weather conditions and aggressive substances, especially close to
frequently used roads, in coastal and industrial areas. Therefore, please
consider the following care instructions. Unfortunately, we cannot accept any
liability for damage if these instructions are not being observed. Aggressive
dirt such as bird droppings should be removed as quickly as possible.
Aggressive stains such as bird droppings NOTICE should be removed as soon as
possible.
Never use abrasive detergents such as steel NOTICE wool or scouring milk!
After the cleaning with clear water wipe with damp cloth and rub dry to avoid
lime traces. Lime residues can be avoided by using demineralised water.
Stainless steel PVD coated PVD coated, chrome-plated or gold-plated surfaces
are recommended to be cleaned with a greasedissolving detergent and clear
water or with a clean and dust-free microfibre cloth. For high-gloss surfaces,
use a scratch-free cloth (e.g. cleaning cloth for glasses, furniture polishing
cloth, etc.).
Lacquered surfaces Clean painted surfaces and lettering with a soft, scratch-
free cloth moistened with a mild soap solution (e.g. cleaning cloth for
glasses, furniture polishing cloth, etc.). To prevent stains or
discolouration, the detergents should be wiped off without leaving any
residue. Be particularly careful with lettering in order not to damage the
film or the print.
Warm water is usually sufficient, if necessary with a little detergent, a soft cloth or brush. Plastic parts (camera or name tags) must not be treated with metal care products. Remove all residues of cleaning agents or lubricants to avoid stains or discolouration after the maintenance.
Stainless Steel Only high-quality stainless steel is used for all available DoorBird door stations. However, high-quality stainless steel can also rust, as approx. 70% of stainless steel is made of iron. Rust resistance is only achieved by a protective layer (also called passive layer), which covers the iron like a skin. This protective layer consists essentially of chromium and other precious metals.
Iron particles, grinding dust and chips deposited on stainless steel can lead to corrosion (rust film). These iron particles can be found everywhere, but especially in coastal and industrial areas and close to frequently 16
TROUBLESHOOTING
The device does not power up
If the device is to be supplied with power by a mains adapter, plug the power
adapter of the device into a wall socket. If the power adapter was already
plugged into a wall socket, check if the cables and wires are correctly
connected to the screw connection terminal. In most cases, removing the cable
and wires from the screw connection terminal plug and reconnecting them to the
screw connection terminal plug helps (loose contact). If you are powering more
than one device simultanously with one mains adapter, check if the mains
adapter is able to deliver enough power over the full cable length.
If the device is to be powered via PoE, switch on the PoE-Switch/ PoE-Injector
which is connected to the device. If the PoE-Switch/ PoE-Injector was already
switched on, check if the cables and wires are correctly connected screw
connection terminal. In most cases, removing the cable and wires from the
screw connection terminal plug and reconnecting them to the screw connection
terminal plug helps (loose contact). If the problem still exists, please check
if your PoE-Switch / PoE Injector supports the PoE Standard IEEE 802.3af Mode
A, see also www.doorbird.com/poe
If the device is to be supplied with power by a DIN-rail power supply, switch
on the DIN-rail power supply If the DIN-rail power supply was already switched
on, check if the cables and wires are correctly connected to the screw
connection terminal. In most cases, removing the cable and wires from the
screw connection terminal plug and reconnecting them to the screw connection
terminal plug helps (loose contact). If you are powering more than one device
simultanously with one DIN-rail power supply, check if the DIN-rail power
supply is able to deliver enough power over the full cable length.
The device does not connect to network via network cable (“No Network”
diagnosis sound)
In most cases, removing the cable and wires from the screw connection terminal
plug and reconnecting them to the screw connection terminal plug helps (loose
contact). If the problem still exists, please check if the network cable is
properly connected to your router / switch and the network cable is not
broken.
If the problem still exists, please check if your Router has DHCP turned on
and is able to assign an IP address to the device.
The device does not connect to Internet (“No Internet” diagnosis sound) In
most cases, your Internet is down or your router blocks Internet access for
the device. Please see www.doorbird.com/downloads/ ports.pdf If the problem
still exists, please check if your Router has DHCP turned on and is able to
assign an IP address to the device. The device does not connect to Internet In
most cases, your Internet is down or your router blocks Internet access for
the device. Please see www.doorbird.com/downloads/ports.pdf
17
ENGLISH
LEGAL NOTES
General remarks 1. DoorBird is a registered trademark of Bird Home Automation
GmbH.
2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch, iOS,
iPhone and iPod touch are trademarks of Apple Inc.
3. Google, Android and Google Play are trademarks of Google, Inc.
4. The Bluetooth® word mark and logos are registered trademarks of Bluetooth
SIG, Inc.
5. All other company and product names may be trademarks of the respective
companies with which they are associated.
6. We reserve the right to make changes to our products in the interests of
technical advancement. The products shown may also look different from the
products supplied based on ongoing enhancement.
7. Reproducing or using texts, illustrations and photos from this instruction
manual in any media even if only in the form of excerpts shall only be
permitted with our express written consent.
8. The design of this manual is subject to copyright protection. We do not
accept any liability for any errors or any erroneous content or printing
errors (even in the case of technical specifications or within graphics and
technical sketches).
9. Our products are in compliance with all technical guidelines, electrical
and telecommunications regulations applicable in Germany, the EU and the USA.
10. Our products and also the components contained therein (ICs, software,
etc.) may only be used for civilian non-military purposes.
several weeks. As soon as a product receives a firmware update, the system
will be installed and will restart by itself. Installed firmware updates
cannot be undone. Since the products and software of Bird Home Automation GmbH
are not explicitly customer-specific products, a customer cannot deny an
automatic update if the product is connected to the Internet or to the Bird
Home Automation GmbH’s server.
Publisher Bird Home Automation GmbH Uhlandstraße 165 10719 Berlin Germany
Web: www.doorbird.com Email: hello@doorbird.com
Data privacy and data security 1. For maximum security, the device uses the
same encryption
technologies as are used in online banking. For your security, no port
forwarding or DynDNS is used either.
2. The data centre location for remote access over the Internet by means of
an App is obligatory in the EU if the determined Internet IP-Address location
of the device is within the EU. The data centre is operated in line with the
most stringent security standards.
3. Video, audio and any other surveillance methods can be regulated by laws
that vary from country to country. Check the laws in your local region before
installing and using this device for surveillance purposes.
If the device is a door-, indoor station or camera: · In many countries video
and voice signal may only be transmitted
once a visitor has rung the bell (data privacy, configurable in the App).
· Please carry out the mounting in such a way that the detection range of the
camera limits the device exclusively to the immediate entrance area.
· The device may come with a visitor history and motion sensor. You can
activate/deactivate this function if required.
If necessary, indicate the presence of the device in a suitable place and in a
suitable form.
Please observe any relevant country-specific statutory regulations concerning
the use of surveillance components and surveillance cameras applicable at the
installation site.
Check with the property owner and your house community if you are allowed to
install and use this product. Bird Home Automation GmbH cannot be held
responsible for any miss-use or miss-configuration of this product, including
the unauthorized opening of a door.
Bird Home Automation cannot be held responsible for damages caused by improper
existing installations or improper installation.
Software and operating system’s updates (so-called “firmware updates”) are
generally automatically installed on the products of Bird Home Automation GmbH
via Internet, if technically possible. Automatic firmware updates keep the
productssoftware up to date so that they always work reliably, safely and efficiently. Through further development, features can be added, extended or slightly changed. Major changes or limitations to existing features will generally occur if Bird Home Automation GmbH deems it necessary (e.g. for data protection, data security or stability reasons, or to keep them up to date). When a firmware update is available, Bird Home Automation GmbH
s servers
generally automatically distribute it to all compatible products connected to
the Internet or Bird Home Automation GmbH`s servers. This process is gradual
and can take
18
It is possible that these manual still contains typographical errors or printing errors.The information in this manual will be checked regularly and corrections will be made in the next version. We accept no liability for errors of a technical or printing nature and their consequences.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>