HAMPTON BAY GS-W070803BK 1-Light Sconce User Guide
- June 6, 2024
- HAMPTON BAY
Table of Contents
USE AND CARE GUIDE
1-LIGHT SCONCE
Item #XXXXXXXXXX
Model #GS-W070803BK
Item #XXXXXXXXXX
Model #GS-W070803BZ
THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through
the purchase of this 1-light sconce.
We strive to continually create quality products designed to enhance your
home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Hampton Bay!
Safety Information
WARNING: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation. Please call our Customer Service Team at 1-855-HD-HAMPTON.
WARNING: RISK OF ELECTRIC SHOCK. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the switch is not sufficient to prevent electrical shock. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.
Warranty
THREE YEARS MANUFACTURER WARRANTY WHAT IS COVERED The manufacturer warrants
this unit to be free from defects in materials and workmanship for a period of
three (3) years from the date of purchase. This warranty applies only to the
original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the
product at the manufacturer’s discretion, provided that the product has not
been damaged through misuse, abuse, accident, modifications, alterations,
neglect, or mishandling. This warranty shall not apply to any product that is
found to have been improperly installed, set up, or used in any way not in
accordance with the instructions supplied with the product. This warranty
shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, faulty installation, or any other
failure not relating to faulty material or workmanship. This warranty shall
not apply to the finish on any portion of the product, such as surface and/or
weathering, as this is considered normal wear and tear.
WHAT IS NOT COVERED
The manufacturer does not warrant and specifically disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than the
warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/ expense costs involved in the
replacement or repair of said product. Contact the Customer Service Team at
1-855-HD-HAMPTON or visit www.hamptonbay.com.
Pre-Installation
- Read all instructions before assembling.
- To avoid damaging this product, assemble it on a soft, non-abrasive surface such as a carpet or cardboard.
- Keep the receipt and these instructions for proof of purchase.
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| AA | Junction Box Screw | 2 |
| BB | Wire Connector | 3 |
PACKAGE CONTENTS
| Part | Description | Quantity |
|---|---|---|
| A | Mounting bar (preassembled to canopy (B)) | 1 |
| B | Canopy | 1 |
| C | Canopy nut (preassembled to canopy (B)) | 1 |
| D | Lamp body | 1 |
| E | Shade | 1 |
| F | Socket ring (preassembled to lamp body (D)) | 1 |
Installation
Installing the mounting bar
- Carefully unpack and lay all parts on a clean, level surface.
- Unscrew the canopy nut (C) from the canopy (B) and detach the mounting bar (A).
- Attach the mounting bar (A) to the junction box (not included) with junction box screws (AA).
NOTE: The preassembled screws from the mounting bracket should be in a horizontal position.
Making the electrical connections
NOTE: Make the connections to a 120V AC 60Hz circuit.
- Connect the white wires from the fixture to the white wire of the supply circuit.
- Connect the black wires from the fixture to the black wire of the supply circuit.
- Wrap the bare copper grounding wire from the fixture around the green screw on the mounting bar (A), then connect it to the grounding conductor of the supply circuit.
- Use U.L./C.S.A. listed wire connectors (BB) suitable for the size, type, and a number of conductors. Secure the wire connectors (BB) with U.L./C.S.A. listed electrical tape (not included).
- Place the canopy (B) against the mounting surface, allowing the preassembled screws on the mounting bar (A) to pass through the canopy (B) and secure with the canopy nut (C).
Installing the shade
Remove the preassembled socket ring (F) from the lamp body (D).
Place the shade (E) over the sockets on the lamp body (D) and then secure with
the socket ring (F).
Installing the bulb
Uses one 60 Watt Max E26 Type A or Type S Bulb or CFL or LED equivalent (not included).
Care and Cleaning
Clean the unit with a soft, dry cloth.
Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Causes | Solutions |
|---|
The bulb will not light.
The fuse blows or circuit breaker blows when the light is turned on.| The bulb
is burned out.
The power is off.
The circuit breaker is off.
There is an exposed wire.| Replace the light bulb.
Ensure the power supply is on.
Ensure the circuit breaker is in the ON position.
Discontinue the use of the lamp.
Contact a qualified electrician or call the
Customer Service Team at 1-855-HD-HAMPTON.
Questions, problems, missing parts? Before returning to the store, call
Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday,
9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
Retain this manual for future use.