BRISTAN EV KIT-EFB C Evo Riser Rails and Kits Instruction Manual
- June 6, 2024
- BRISTAN
Table of Contents
BRISTAN EV KIT-EFB C Evo Riser Rails and Kits
Please keep this booklet for future reference.
Installer, when you have read these instructions please ensure you leave them
with the user.
Thank you for choosing Bristan, the UK’s leading taps and showers expert. We
have designed these products with your enjoyment in mind.
To ensure that they work to their full potential, they need to be fitted
correctly. These fitting instructions have been created to give you all of the
information you need and, if you need any further help, please do not hesitate
to give us a call on 0300 026 6273.
Important Safety Information
Please read these instructions thoroughly and retain for future use.
All products manufactured and supplied by Bristan are safe provided they are
installed, used correctly and receive regular maintenance in accordance with
these instructions.
If you are in any doubt about your ability to install this product safely you
must employ the services of an experienced qualified plumber.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and current
byelaws. For full Installation Requirements & Notes (IRN) please visit
wras.co.uk/directory
Before starting any installation please consider the following:
Before drilling into walls, check that there are no hidden electrical
wires, cables or water supply pipes. This can be checked with the aid of an
electronic detector.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
- Remove all packaging and check the components for damage.
- Do not use if the shower head or hose has been damaged or blocked.
- Do not block the flow of water from the shower head, by placing it (smothering it) on your hand or any other part of your body or foreign object.
- Do not crush or kink the shower hose, this could damage the hose and cause leaks.
- This product must not be modified in any way as this will invalidate the guarantee.
If in doubt, contact a registered plumber or your Local Water Authority or the Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing, 64 Station Lane, Hornchurch, Essex,
RM12 6NB, Tel: 01708 472791
Dimensions (mm)
Pack Contents
- Wall Brackets x2
- Riser Rail x1
- Slider x1
- Handset x1
- Fixings x4
- Hose x1
- Shelf *not shown x1
Installation
-
Mark the position
Position the assembled riser rail onto the wall, bearing in mind the highest maximum position required for the handset. With the riser rail vertical, mark the position of the wall brackets onto the wall surface. -
Attach wall bracket fixings
Remove the wall brackets from the rail and then remove the fixings from the wall brackets.
Position the fixing bracket in the marked positions against the wall, ensure they are vertically in line with each other and mark the centres of the fixing holes onto the wall.
Warning: Please check for any hidden pipes and cables before drilling holes in the wall.
Drill suitable holes and insert the wall plugs. Securely attach the fixing brackets to the wall using the screws. -
Insert riser rail
Ensure the rail clamps are in position and push the riser rail up through the bottom wall bracket.
Push the shelf and slider down onto the riser. Ensure the slider it is the correct way up, as shown opposite.
Push the riser rail up through the top wall bracket. -
Tighten rail clamps
Centre the riser rail within the wall brackets and tighten both clamps located inside the wall bracket onto the rail. -
Fit the riser to the wall
Slide the riser brackets over the bracket fixings attached to the wall. Tighten the grub screw on the underside of both top and bottom wall brackets using a 2.5mm hexagonal key. -
Connect shower hose
Screw the shower hose (ribbed end) onto the shower valve outlet (not supplied), ensuring the rubber washer is fitted. -
Connect shower hose to shower head
Screw the shower hose (conical end) onto the shower head ensuring that the rubber washer is fitted.
Place the shower head into the slider.
Adjusting the Slider
Press the button on the underside of the slider to move higher or lower for
user height.
To adjust the angle of the shower head, twist the slider bracket to the
desired position.
Operation
EEVK Multi-Function Handset
The multi-function shower head has 3 spray functions, spray, jet and
combination. Simply rotate the spray head one way or the other to the desired
spray pattern.
Maintenance
General Cleaning
Bristan products are made from premium materials, with hand polishing and
electroplated finishes.
Your product should be regularly cleaned with warm water, a mild pH-neutral
liquid soap, and polished with a soft cloth. Any residues from soap,
toothpaste, shampoos and shower gels can cause blemishes if not rinsed off
straight after use.
Household bleaches and cleaners contain harsh chemicals and may damage the
surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges,
steel wool or anything similar.
Some surfaces such as nickel and pewter may be affected by the dye found in
some cloths, so it is also important to avoid hanging cloths on spouts.
Your Bristan shower head has rub-clean nozzles for easy cleaning. Simply rub
your fingers across the rubber spray jets regularly and before you turn the
shower on to remove any scale or debris.
Cleaning the Shower Head
The hardness of the water in your area will determine how often you should
clean your shower head. Build up of scale in particularly hard water areas
combined with constant use means you may need to clean your shower head once a
week. To ensure continued performance the shower head needs to be regularly
de-scaled.
Troubleshooting
| Symptom | Cause | Remedy |
|---|
No flow or low flow rate
| Partially closed isolation valve.| Open isolation valve.
Instantaneous water heater cycles on and off as flow rate or pressure is too
low.| Increase water flow rate or pressure through system.
Head of water is below the minimum distance required.| Refer to the shower
valve’s instruction booklet for minimum distance required.
Airlock or partial blockage in the supply pipework.| Flush through pipework to
ensure removal of debris and any airlocks.
Inlet filter in shower valve is blocked| Refer to the shower valve’s
instruction booklet for guidance.
Check the shower head, hose and filters for any blockage.| Clean as per the
Maintenance section.
Shower hose is kinked, causing a blockage.| Un-kink the shower hose. Replace
if damaged.
Water leaking from shower head
| This is normal for a short time after using the shower.| This is caused by residual water tension, the build up of water in the shower. Adjust the
angle of the shower head as necessary to vary draining time.
Shower valve failing to close fully, possibly due to water borne debris.| Refer to the shower valve’s instruction booklet for guidance.
Issue: D4
Part Number: COM EV KITS
Bristan Group Ltd.
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
Web: www.bristan.com
Email: enquire@bristan.com
A Masco Company
At Bristan, we want to make things as easy as possible for our customers.
That’s why we offer solid guarantees on all our products, effective from the
date of purchase, to give you peace of mind. To start your free guarantee
simply scan the QR code and register your product.
Alternatively visit
www.bristan.com/register
For any other queries, please call our Customer Service on 0330 026 6273 where
our expert team of advisors will be able to offer you any help and advice
For full guarantee terms and conditions visit
www.bristan.com/guarantees
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>