Nikabe 23907 D3 Bluetooth DAC Stereo Amplifier User Manual
- June 6, 2024
- Nikabe
Table of Contents
Nikabe
23907 D3 Bluetooth DAC Stereo Amplifier
User Manual
D3 Bluetooth DAC stereo amplifier
Item: 23907
www.nikabe.com Box 50435 Malmo Sweden 2021-05.31
Overview
1. Power indicator
2. Bluetooth indicator
3. Optical indicator
4. Line-in indicator
5. AUX indicator
6. Remote sensor
7. Volume knob/Input sensor
8. Antenna| 9. RCA audio input
10. Subwoofer output
11. Line-in
12. Optical input
13. Speaker output -L/R
14. Speaker output +IJR
15. Power input
16. On/off switch
---|---
Remote control
- On/off button
- Optical source
- Volume +/-
- Previous/Next track in Bluetooth mode
- Line-in source
- Play/pause in Bluetooth mode
- AUX/RCA source
- Mute
- Bluetooth mode
Specifications
Power supply:
Output power:
Frequency:
Impedance.
Inputs:
Outputs:
Bluetooth version:
Bluetooth range:
Wireless frequency:
Transmission power:
Weight:
Dimension:| AC 100-240 V, 50/60 Hz, 100 W
2x 50 W RMS
20 Hz – 20 KHz
4Ω
Bluetooth, S/PDIF optical, 3.5 mm, RCA
Speaker LR, subwoofer line (c250 Hz)
5.0
10m
2402 – 2480 Mhz
20 mW (max)
1.3 kg
190 x 139 x 52 mm
---|---
Use
- Connect the power cable to the power input (15) and to a wall outlet.
- Connect your devices to the amplifier (see “Connecting your devices”).
- Set the Power switch (16) to on. The Power indicator (1) turns on after about two seconds.
- Choose an input source with the remote control or the Volume knob (7). The corresponding indicator lights up.
- Control the playback with the remote control.
Connecting your devices
Connect your subwoofer to the subwoofer output (10), SUB out.
Connect your speakers to the speaker outputs (13, 14) with speaker cables.
Make sure to connect the positive (+) wire to the positive (+) output and the
negative wire (-) to the negative (-) output.
Connect your audio source (e.g. phone, DVD, gaming console) to a suitable
input source. Choose the corresponding input source with the remote control or
the volume knob.
If you are connecting your phone or tablet to the amplifier with a 3.5 mm
cable, connect it to the line-in input (11).
If you are using an RCA cable, connect it to the RCA input and make sure to
connect thet” plug to the ‘L” input and the ‘R’ plug to the “R’ input.
Bluetooth pairing
Press the Bluetooth button on the remote (9) to activate Bluetooth. The
Bluetooth indicator (2) starts flashing blue. Activate Bluetooth on your
Bluetooth device and connect to “Nikabe BT Amp”. The Bluetooth indicator turns
solid blue when the pairing is successful.
Press and hold the Bluetooth button on the remote control to disconnect and
re-enter pairing mode.
Connection diagram
Safety information
This equipment is not intended for use by persons with reduced physical,
sensory or mental capabilities, or lack of experience or knowledge unless they
are supervised or have received instructions concerning the use of the
equipment by a person responsible for their safety.
Do not attempt to service or disassemble the amplifier yourself.
Never insert any objects into the amplifier.
For domestic use only. Simplified EU Declaration of Conformity Kjell & Company
hereby declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
Full text of the EU declaration of conformity is available at
www.kjell.com/23907
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>