SONOFF S40ZBTPB Lite Smart Plug User Manual

SONOFF S40ZBTPB Lite Smart Plug User Manual

Product Introduction

The device weight ls less than 1 kg. The installation height of less than 2 mis recommended.

Features

SONOFF smart device (Zigbee version) with Zigbee wireless  communication protocol that allows you to remotely turn on, schedule on/off and set smart scenes to trrigger other devices, etc:. by connecting Zigbee hub.

Remote Control                     Single/Countdown Timing Voice Control

Share Control                 Smart Scene            Camera Linking

DAbovefunctions are determined by Zig bee Hub.

Pair with eWelinkApp

1. Download the eWelink App

2. Pair SON OFF ZB Bridge to your eWeLink account

3. Power on

After powering on, the device will enter the pairing mode defaulted during the first use and the Zigbee LED signal indicator will Nflash slowly”.
The device will exit the pairing mode if you do not operate it within 3 minutes. When you want to enter the pairing mode again, long press the button on the device for 5 seconds until the Zigbee signal light “flashes slowly” and release.

4. Add iPlug to the ZB Bridge
   
   Open eWeLinkApp, tapMAddN icon on theZB Bridge interface, then wait to looking for and add the sub-devices.

Pair with Amazon Echo

1. Download the latest Amazon Alexa App and pair it with Amazon Echo with built-in Zigbee hub.

2. Power on iPlug, then it defaulted to enter the pairing mode and the Zigbee LED signal indicatorMflashes slowly”.

3. Ask the Alexa Echo to discover the devices automatically by saying •Alexa, discover my devices•.

lffailed to pairwithin 3mins, iPlugwill exit the pairing mode. Long press the button on iPlug for 5s to make it enter the pairing mode if you need to pair again.

HAVE A PROBLEM?

We are so sorry for the inconvenience caused by the product. Please contact us for help via the email address below.

support@itead.cc We will get back to you as soon as possible.

More APP application platforms and gateway recommendations

This device supports the following gateways besides SON OFF Zigbee:

Echo Studio
Echo (4th Gen)
Echo Plus (Model: ZE39KL)
2nd Gen Echo Show (Model: DW84JL)
2nd Gen Echo Plus (Model: L9D29R)
Samsung Smartlhings hub

Gateway adding Instruction:

1. Refertothegatewayuser manual to download the matched APP and get it paired.
2. Set iPlug to the pairing mode.
3. Add iPlugfollowing the prompt on the APP and select eWeLink or SONOFFwhen adding.

lfyou failed to add the sub-device, please take it closer to the Bridge and try again.

Specifications

Factory Reset

Deleting the device on the eWelinkapp indicates you restore it to factory setting.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compl ia nee cou Id avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

https:/ /son off. tech/userman ua Is
Scan the QR code or visit the website to check the lastest user manual and help.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>