FEIT Electric A450 LED Smart Camera Bulb with Adjustable Head Installation Guide
- June 6, 2024
- Feit Electric
Table of Contents
FEIT Electric A450 LED Smart Camera Bulb with Adjustable Head
Thankyou for your purchase. Questions, comments or feedback? We’d love to hear from you.
Visit feit.com/help for support.
READ BEFORE INSTALLATION. SAVE THESE INSTRUCTIONS.
We appreciate the trust and confidence you have placed in Feil Electric through the purchase of this product. We strive to continually create quality product& designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric
Safety Information
IMPORTANT SAFEGUARDS:
ALWAYS FOLLOW BASIC SAFETY PREC’AUTIONS WHEN USING ELECTRICAL PRODUCTS,
ESPECIALl.Y WHEN CHILDREN ARE PRESENT.
Supplier’s Declaration of Conformity:
47 CFR § 2.1 on Compliance Information Responsible Party:
Feit Electric Company
4901 Gregg Road,
Pico Rivera, CA 90660, USA
562-463-2852
Unique Identifier:
A450/850/CAMWIFI/LED
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause hannful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, If not Installed and used In accordance with the Instructions, may cause harmful Interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).
- The device has been evaluated to meet general RF exposure requirement.
- The device can be used in portable exposure condition without restriction.
- The device can be used in mobile (min 7 .87 in.) exposure condition without restriction.
Limited Warranty
This product is warrantied 1D be free from defects in workmanship and
materials for up 1D 1 year from date of purchase. If the product falls within
the warranty period, please visit feit.com/help for Instructions on
replacement/refund or call 866.326.BULB. REPLACEMENT OR REFUND IS YOUR SOLE
REMEDY.
EXCEPT TO THE EXTENT PROHI BITED BY APPLICABLE LAW, IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCI.UDED.
Some states and provinces do not allow the exclusion of Incidental or consequential damages, so the above !Imitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Assembly
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
| Part | description | Quantity |
|---|---|---|
| AA | Smart Camera Bulb | 1 |
| BB | Reset Pin | 1 |
Description
Input Power: 120VAC 60Hz, 1OW
Status Light
| ****
Blinking RED= Pairing Mode Solid RED = Rebooting
Blinking BLUE = No Wi-Fi Connection Solid BLUE= Connected to Wi-Fi
| ****
MlrcoSD
Card Slot
Reset
Button
| Add a maximum 1 28GB MicroSD card (sold separately) to enable recording.
Only supports microSDcard with FAT32 format.
Press and hold for 5 seconds with the Reset Pin (BB) to reset the camera.
Installation
Installing the smart camera bulb
Turn OFF the light switch before installing. Screw in the Smart Camera Bulb (AA) clockwise into an E26 socket until it is fully secure.
Adjusting the smart
camera bulb head angle
Turn ON the light switch. Add the device to the Feit Electric app (see the App Setup section). Carefully pan or tilt the camera head until the desired viewing angle is achieved.
App Setup
Downloading and installing the Feit Electric app
- Search for the Feit Electric app in the App Store or Google Play Store.
- Download and install the Feit Electric app on your smart device.
- Connect to a 2.4GHz Wi-Fi network that covers your installation location.
Setting Up the Smart Camera Bulb using the Feit Electric App
- Check to be sure the camera is in pairing mode. The RED status light must be blinking rapidly to connect. If the light is not already blinking, press and hold the Reset Button until you hear an audible tone. Use the Feit Electric app to complete the setup.
- Tap Add Device or the + sign. Tap Security & Camera and then select Camera. You will be prompt-ed to enter your Wi-Fi network and password.
- Follow the directions in the Feit Electric app to pair your device using the QR code.
- You can find more pairing methods in the dropdown menu on the device set-up page.
Need Help?
Thank you for your purchase. Questions, comments or feedback? We’d love to
hear from you. Visit feit.com/help for support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>