GALLAGHER W-0 Weigh Scale User Guide

GALLAGHER W-0 Weigh Scale

Thank you for purchasing the Gallagher W-0 Weigh Scale unit. The Gallagher range of weighing systems is simple, tough, innovative and reliable.

Follow these instructions for the setup and first use of the W-0.

BOX CONTENTS

The Gallagher W-0 box contains:

• W-0 weighing unit
• 110V – 230V Mains AC adapter
• Mounting bracket and mounting hardware

SPECIFICATIONS

• Operating Temperature      -20oC to + 70oC
• Battery charge Temperature -0oC to +50oC
• Environmental Protection Rating IP66
• Weight                                     1.1 kg
• Estimated battery run time   27 hours

CHARGING THE BATTERY

To ensure optimum performance of the W-0, it is recommended that the internal battery is charged for a minimum of 10 hours before fi rst time use.

Important:

• Charging of the W-0 should be in a cool (+10oC to +30oC) place.
• If the W-0 is to be stored for an extended period, this should be in a cool dry place (–20oC to 25oC, humidity 45% to 85%) with a fully charged battery. The W-0 should be charged until full every 6 months.
• Always charge the battery indoors.

1. Connect the power adapter at the base of the unit and plug the W-0 into a power outlet. The charging icon will display on the screen.
   
   Warning: The power adaptor is intended for indoor use only. Do not expose to rain or dampness.

2. When the charge shows 100%, the W-0 is ready to use with or without the power adapter.

Note:

• When the W-0 is in use, the battery icon will display and show remaining charge.
• When using the scale and the charge level falls below 5% the battery icon will fl ash. You will have about 60 minutes to complete the weighing session before the W-0 must be charged.
• When the charge level becomes critical, the unit will sound 3 quick beeps and the LED will flash 3 times, then shut down.
• Charging outside the recommended temperature range will reduce charging performance. When charging above 40oC, the charging time is increased.
• If charging temperatures have been exceeded, charging will stop until the unit cools down. The charge indication will stop in this condition.
• If a battery error occurs the battery indicator will flash all the segments.
  Return the Weigh Scale to a Gallagher Authorised Service Centre for battery replacement.

UNDERSTANDING THE W-0 WEIGHING UNIT

Battery Charge Status

When the battery level drops to 0%, three beeps will sound and the red weight lock LED will flash three times. The scale will rapidly sound 4 beeps then shut down.

Setting up the W-0 for first-time use

Set the weight unit

Turn on the W-0 scale.
To change the weight unit, press and hold down the Mode button for 3 seconds. A beep will sound when the weight unit changes between kgs and lbs.

Select the weighing mode
Press the Mode button to turn Auto weight lock on or off . When AUTO is not displayed the scale is in Manual mode.

Weighing Modes

AUTO

(Automatic)

| In Automatic mode the W-0 will automatically start weighing the animal. When the scale has determined an accurate weight, it will lock on to the measurement and display it on the screen.

This mode is recommended for yards that are well set up and allow the animals to flow smoothly.

---|---
(Manual)| The W-0 is in Manual mode when AUTO is not displayed.

This mode allows the operator to decide when the measurement is made by pressing the Weigh button to lock the weight.
Manual mode is recommended for yards that do not allow the animals to flow smoothly or where the animals are disruptive. The operator has greater control over the weighing session.

INSTALLATION

Installing the W-0
The W-0 can be placed on a tabletop or mounted on the bracket supplied.

Installing the Scale bracket
The bracket can be mounted on a flat vertical surface, a round post, or a rail.
To mount the bracket on a flat vertical surface, or a round wooden post,use the 3 x tek screws included with the unit.

To mount the bracket on either a vertical or horizontal bar, use the ‘U’ bolts included with the unit.

Important:
It is not recommended to mount the W-0 bracket on the weighing crate or chute as interaction with the scale can impair weighing performance.

Installing the loadbars

It is recommended that you use Gallagher Loadbars with the W-0 Scale.
The W-0 recognises other most commonly available Loadbar sets. If you are not using Gallagher Loadbars.

Steps to install loadbars

1. Select a weighing site that provides a solid, level and well drained surface.

2. Ensure the loadbars and platform are well secured and clear of any obstructions.

3. Either bolt the loadbars to the concrete pad or locate them on studs set into the concrete. It is important that the loadbars and platform sit flat without any rocking or twisting to avoid weighing inaccuracies.
   Note: It may be necessary to shim the loadbars or platform to ensure there are no twisting pressures within the platform. Weights should be evenly distributed over the top of the weight bars.

4. Connect the loadbar cables to the W-0.
   A beep will sound indicating a successful connection/ disconnection of the loadbars.

WARNING – Do not weld the loadbars or any structure that they are attached to. Loadbars contain sensitive electronic devices which will be damaged by welding. Damage caused by welding will void warranty.

Position the W-0:

• clear of the platform to ensure it does not interfere with the fl ow of animals during the weighing cycle
• within easy reach of the loadbar leads
• within easy reach of the operator (for manual weighing)

WEIGHING AN ANIMAL

There are 2 ways to use the W-0 scale. It can be used on its own or used in conjunction with the Gallagher Animal Perfomance mobile app. Use the app if you want to record your session.
Before you begin weighing:

1. Check loadbars are connected to the W-0.
2. Turn on the W-0.
3. Check the weight displayed is Zero. If not, press the ZERO button.

Gallagher Animal Performance mobile app

• The Gallagher Animal Performance mobile app is used to record live sessions and control the W-0 Scale.
• Use your mobile device to control your weighing sessions.
• After weighing your animals, sync your phone app and the session data will be available in the Gallagher Animal Performance cloud software, where you can monitor animal weights and weight gains.
• Download the app from Google Play or the App Store.
  Open the Animal Performance app and if required, follow the prompts to create a Gallagher Account.

Start a Weighing Session using the Gallagher

Animal Performance app:

1. Open the Gallagher Animal Performance app on yourmobile device. From the Home screen, tap New Session, type in a session name and tap Done.
2. The app will begin searching for the W-0 and any other devices within range. Select the W-0 from the devices list and tap Connect.
3. The weigh screen will open and you are ready to begin weighing. Refer to Weighing Animals (p. 9)

Note: If you have previously connected the W-0 with your mobile device, and come within range of the W-0, it will automatically connect.

Understanding the weighing screen

Start a Weighing Session on the W-0 scale:
If you are weighing animals without the Animal Performance app, once the scale is turned on and weight displayed is zero, you can start weighing your animals. Refer to Weighing Animals (below).
Note: If using the scale only, animal weights are not recorded.

Weighing animals

1. Load the fi rst animal onto the platform. Ensure the animal is entirely supported by the platform – no hooves on the ground – and that no object is resting on the animal.
2. In AUTO mode| •  the W-0 will automatically start weighing

• when the weight becomes stable it will lock and remain on screen until the animal leaves the platform.

• For App users: type in a VID number (if you want to record this. Either tap VID or tap the Actions button > Add VID.

---|---
In Manual mode| •press the Weigh button to start weighing. When the weight becomes stable it will lock and remain on screen until the animal leaves the platform.

• For App users: type in a VID number (if you want to record this). Either tap VID or tap the Actions button > Add VID.

Important: If the weight displayed does not always return to 0.0 after weighing, check for dirt or manure that may have been left on the platform.
The W-0 can be re-zeroed by pressing the >0< (Zero) button.

• When the weight locks, there will be a beep from the scale and a red light above the Weigh button displays briefly.
  For App users: the mobile device will beep and vibrate. The weight will be recorded in the session on the app.

• In either mode, you can re-weigh an animal by pressing Weigh after a successful weight lock.

Completing a Weighing Session using the app

When a weighing session is completed (i.e. all animals weighed), the recorded session on the mobile app can be synced to the Animal Performance cloud software.
From the Home screen, tap the Menu button, then tap Sync.

• The Syncing process will automatically begin and any differences in session and animal data recorded in the app or in Gallagher Animal Performance will be updated.
• After syncing, the same data will be present on the W0 and in Animal Performance.
• To view your animal data, login to the Gallagher Animal Performance Web App:
  https://am.app.gallagher.com/amc/dashboard

CARE AND MAINTENANCE

The W-0 is a tough and reliable product designed for use in typical livestock environments. Proper care and maintenance can extend its life.
Listed below are guidelines for keeping the W-0 in good condition.

• Do not expose the W-0 to excessive temperatures or fire. (Below -20oC or above +70oC).

• Do not submerge the W-0 in any liquid.

• Store in a cool, dry place. Avoid storing in direct sunlight.

• After use, clean with a damp cloth. Take care not to scratch the display.

• If storing the W-0 for a long time, store with the battery fully charged.

• If battery fl uid comes in contact with:
  Eyes – flush the affected area with water for at least 15 minutes. Ensure adequate flushing by separating the eyelids with fingers. Call a physician.
  Skin – immediately fl ush with water and/or soap.

• This Weigh Scale contains a Lithium battery which is not user-replaceable.
  The lithium battery must be replaced by a trained professional using a Gallagher-approved battery. Return the unit to a Gallagher Authorised Service Centre for battery replacement.

Software Updates

It is important to update the W-0 software from time to time to ensure you have the latest enhancements.
Updates are regularly released to enhance the features of the scale or to correct issues.

1. From the Weighing screen, tap Settngs (top right of screen).
2. Tap Update under the W-0 Firmware section.
3. Follow the instructions on the screen to complete the upgrade.

APPROVALS AND STANDARDS

This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please
contact your local city recycling offi ce or the dealer from whom you purchased the product.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditons: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecton against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Caution: Changes or modifications not expressly approved by Gallagher Group Limited could void the user’s authority to operate the equipment.

Industry
Canada

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use by Gallagher Group Limited is under license. Other trademarks and trade names are those of their respective owners.

www.gallagher.com
Gallagher Private Bag 3026, Hamilton, New Zealand

References

• Animal Performance
• Gallagher Group Limited
• Dè Officiële Gallagher webshop I De #1 Specialist in Europa!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>