KAISDA Electric Bike User Manual

June 4, 2024
KAISDA

KAISDA Electric Bike

KAISDA Electric Bike product

Safety Instruction

  1. For Safety reasons, it is most important that you read this user’s manual before you operate the bike.
  2. Improper handling can reduce its riding performance and most importantly, cause danger to your safe and healthy.
  3. For handling and maintenance of the bicycle, please refer to the E-BIKE which is an integral part of this e-bike user’s manual!
  4. Do not at any time dismantle or disassemble any of the above e-bike components.
  5. Please check all parts are tighten and locked before riding.
  6. Please make sure that the battery charger and charging plug are always kept dray and never get wet.
  7. When charging, do not place the charger and battery in the direct sunlight or high temperature place.
  8. The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or any other liquid.

Instruction

KAISDA Electric Bike 1

Display operation

Open the Display

Long press Button show OPEN for 2-3 seconds to boot, short press button + 1 -5 gear adjust the speed of the E-BIKE.

Functional Layout

Interface of Display.

Precautions for Operation
Pay attention to safe use. Do not attempt to untie the connector when connecting the battery.

  • Avoiding collision risk.
  • Do not modify system parameters to avoid parameter clutter.
  • Instrumentation error code should be repaired in time.

Battery related information and maintenance

How far can a fully charged battery go? It depends on load weight, road conditions and battery capacity. However, under the same conditions, the average speed 25km/h can continue to travel for a long. When storing batteries for an extended period of time (such as in winter), it is important to place a fully charged battery on a dry, flat surface.

Note
When the battery is not in use, it should be charged every 1-2 months.

Warning

  • Please keep the battery out of reach of children.
  • Do not attempt to turn on the battery.
  • If the battery is damaged in a crash or cycling accident, there is a risk of electrolyte leakage.
  • Beware of chemical burns! And immediately stop using damaged batteries.
  • Do not touch the battery without a cloth or gloves, and make sure the acid does not touch your eyes.

The charging method

When the battery of an electric bicycle needs to be charged, just put the bicycle in the place where the power supply can reach it. First, connect the charging plug of the charger to the charging seat on the battery, and then plug in the power plug of the charger to charge. The battery can be installed on the bicycle for charging, or it can be taken out andplaced in a convenient place for charging. The red light means the battery is charging, and the green light means thebattery is fully charged (wait for 30 minutes after the green light of the charger is displayed before unplugging it).Charging time depends on the battery capacity, the general charging time is 4-6 hours.

Warning
Do not charge for more than 10 hours. Keep away from high temperature environment and store in a cool place.

Installation instructions

Open the carton of the electric bicycle, take out the electric bicycle, and cut off the wrapping rope with tools.

Handlebar installation

Open the folding buckle of the riser. After the riser is aligned with the slot of the riser, lock the quick disassembly rod (note: it must be completed in the folded state.

Raise the riser to lock the folding handle and then fasten the protective sleeve into the clamping slot of the folding handle.

Headlight& fenders installation

KAISDA Electric Bike 8

Loosen the headlight screw from the front fork. Install the headlight into the screw hole of the front fork and tighten the screw with the hexagon tool.

Front wheel installation

KAISDA Electric Bike 9

Cut the wrapping rope, remove the front wheel, remove the front fork protection rod and the front wheel protection cover. Make sure the front and rear wheels are in line before mounting. First pull the wheel up, place the disc brake disc into the front brake clamp, then use the No. 15 wrench to tighten the front flower drum fixing screw. Adjust the adjusting screw of the disc brake so that the disc brake can rotate  without obvious friction.

Pedal installation

Check the two pedal. The pedal with L printed on the end of the core shaft should be installed on the left side of the vehicle without toothed disc and rotate counterclockwise. The pedal with R is installed on the right side with toothed disc and rotate clockwise, then use the No.15 wrench Tighten the foot core shaft (pay attention to screw the foot up by hand and then lock it with a wrench.

Saddle installation

Open the package, take out the seat cushion and seat rod, and then install the rear reflector lamp on the seat rod. Insert the seat rod into the frame. Adjust the seat position to the height most suitable for your riding position, and lock the quick release (please make sure the quick release lock is tight.

Adjust angle of brake lever, meter, gear shifter and louder controller on handle bar, then tighten them with tools.

Remove the battery

  • First open the folding handle safety buckle.KAISDA Electric Bike 14
  • Then open the folding device.

Folding the frame, turn the key which on the battery clockwise turn 3 times after the key is pulled off the battery can be removed (when to the third time ,the key ne to the reach on the top.

KAISDA Electric Bike 17

Accelerator installation instructions

First remove the preinstalled cover on the handlebars, If it is difficult to remove, cut it off with a knife and replace the short handle sleeve. Take out the accelerator from the small box, firstly put the accelerator into the right side of the handlebar, and then put it into the sheath, and then set the short handle sleeve, and knock the sleeve into place with the rubber hammer.  Find the oil line inside the wire harness and plug it into the throttle.

Battery power off and on

Turn the key under the frame counterclockwise turn the first time, the battery to lock with the frame.

Turn the second time, the e bike have connect the power parallel to the frame mean connect the power , turn counterclockwise to turn off the power.

More detail KAISDA electric bike’s installation and repair instructions, any question about the products, please contact. Your satisfaction is our constant pursuit.

Detail Packing       List

Model| Description| Quantity
| E-Bike| 1
| Tool

13 – 15 wrench

9, 14-17 wrench 11

|
| type screwdriver, M6, M5, M4, M3 hexagon| 1
| wrench|

K2

| Manual| 1
| Key| 2
| Charger| 1
| Pedal| 1
| saddle| 1
| Sea Post Rear reflector|

1

| Rear rack|
| | 1
| | 1

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals