beurer BY 110 Video Baby Monitor Instruction Manual

June 6, 2024
Beurer

beurer BY 110 Video Baby Monitor

beurer BY 110 Video Baby Monitor

Included in delivery

Check that the exterior of the cardboard delivery packaging is intact and make sure that all contents are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Service address.

  • 1x camera (baby unit)
  • 1x parent unit
  • 2x mains part plugs
  • 1x lithium-ion battery for parent unit
  • 1x these instructions for use

Signs and symbols

The following symbols are used on the device, in these instructions for use, on the packaging and on the type plate for the device:

Signs and symbols

Warnings and safety notes

WARNING

  • Always position the camera and power cord out of the reach of chil-dren. The power cord may cause strangulation or injury to children.
  • Keep small parts out of reach of children.
  • Keep packaging material away from children (risk of suffocation).
  • Never place the camera in the cot or within reach of your child.
  • Place the camera 2 m away from your baby, in order to minimise the pos-sibility of electrosmog pollution and noise pollution.
  • Make sure that cables are not accessible to your child.
  • Make sure that the video baby monitor is fully functioning before use and check that the battery in the parent unit is sufficiently charged when oper-ating the device with the battery.
  • Never submerge the camera and the parent unit in water. Never rinse it in running water.
  • Never use the camera and the parent unit in proximity to moisture.
  • Do not cover the camera and the parent unit with a towel or cover.
  • Only use the mains part plugs included in delivery.
  • Do not use the cable to pull the mains part plug out of the socket.
  • This device may be used by children over the age of 8 and by people with reduced physical, sensory or mental skills or a lack of experience or knowl-edge, provided that they are supervised or have been instructed on how to use the device safely, and are fully aware of the consequent risks of use.
  • Children must not play with the device.
  • Cleaning and user maintenance must not be performed by children unless supervised.
  • Do not pull, twist or bend the mains cable.
  • Pull the mains part plug out in the case of operational faults before the cleaning process, after charging and when the device is not in use.
  • The camera, the parent unit and the mains part plugs should not come into contact with hot surfaces or sharp-edged objects.
  • Do not use any additional parts that are not recommended by the manufacturer or offered as accessories.

Note

  • Before making a claim, please check the battery in the parent unit and replace it if necessary.
  • Repairs must only be carried out by Customer Services or authorised re-tailers. Under no circumstances should you open or repair the camera or parent unit yourself, as faultless functionality can no longer be guaranteed thereafter. Failure to comply with this instruction will void the warranty.
  • Should you have any questions about using the video baby monitor, please contact either your retailer or Customer Services.

WARNING
Safety notes on handling batteries

  • If the battery leaks, put on protective gloves and clean the battery com-partment with a dry cloth.
  • If your skin or eyes come into contact with fluid from a battery cell, flush out the affected areas with water and seek medical assistance.
  • Choking hazard! Small children may swallow and choke on batteries. There-fore, store batteries out of the reach of small children.
  • Observe the plus (+) and minus (-) polarity signs.
  • Protect batteries from excessive heat.
  • Risk of explosion! Never throw batteries into a fire.
  • If the device is not to be used for a long period of time, remove the batter-ies from the battery compartment.
  • Do not disassemble, split or crush the batteries.
  • Only use chargers specified in the instructions for use.
  • Batteries must be charged correctly prior to use. The instructions from the manufacturer and the specifications in these instructions for use regarding correct charging must be observed at all times
  • Fully charge the battery prior to initial use (see Chapter 6.1)
  • In order to achieve as long a battery service life as possible, fully charge the battery at least 2 times a year.

Intended use

WARNING

  • Only use the device to monitor your baby when you cannot mind your baby directly. It is not a substitute for your own personal, responsible supervision!
  • Any form of improper use can be dangerous.
  • The video baby monitor is only intended for domestic/private use, not for commercial use.

Device description

“Baby” camera

Device description

1. Microphone 5. ON/OFF switch
2. Camera lens 6. Pair button
3. Brightness sensor (night vision function) 7. Connection for mains part

plug
4. Function light

green = camera is ready for use

| 8. Temperature sensor

“Monitor” parent unit

Device description 1

1. ON/OFF button 9. Display
2. Menu button/up direction button 10. Increase volume
3. Microphone 11. Decrease volume
4. Intercom function/increase screen brightness 12. Battery compartment lid
5. OK button 13. Connection for mains part plug

6. Battery status indicator

green = battery fully charged/ parent unit connected to power via mains part plug
red = battery charging

| 14. Stand (fold-out)
7. Back button/down direction button| 15. Speaker
8. Decrease screen brightness| 16. Reset button

Display description

Device description 2

1. Signal strength 10. Timer menu
2. Room temperature display 11. Add camera
3. Timer 12. Camera change menu
4. Energy saving mode 13. Noise sensitivity setting
5. Intercom function 14. Frequency setting
6. Camera number 15. Energy saving mode
7. Battery state 16. Temperature menu
8. Zoom setting 17. Movement sensor setting
9. Lullabies menu 18. Resetting to factory settings

Initial use

Preparing the device for first time use
Before the first use, the batteries should be fully charged. The charging process lasts for approx. 4 hours. The device then offers an operating time of approx. 8 hours. You will get the maximum capacity from your battery if you run down the battery at least once every 6 months. To do this, disconnect the device from the mains and run the battery down through normal use. Afterwards, fully charge the battery again.

The maximum battery capacity can only be reached after it has been charged several times and is dependent on many factors (battery state, ambient temperature, manner and frequency of charging etc)

Initial use of camera

  1. Place the camera on a level, firm surface and point the camera lens at the area that you wish to monitor. Ensure that there are no other electrical de-vices nearby.
    WARNING: Do NOT position the camera within reach of the baby!

  2. Connect the small end of the camera mains part plug to the camera. Connect the other end of the camera mains part plug to a suitable socket.

  3. Slide the ON/OFF switch at the top to “ON” to switch on the camera. The function light on the camera lights up green.

  4. Slide the ON/OFF switch to “OFF” to switch off the camera.

Initial use of parent unit with battery

  1. Open the battery compartment lid on the rear of the parent unit by sliding it sideways.
  2. Slide the battery included in delivery into the battery compartment with the gold +/- surface going first and with the side with writing on it facing upwards, as shown. Ensure that the battery is fully inside the battery compartment, as far as it will go.
  3. Close the battery compartment lid on the rear of the parent unit again, until you can hear and feel it slot into place.
  4. To switch on the parent unit, press and hold the ON/OFF button on the top for approx. 3 seconds. If the camera is already switched on, the transmission image from the camera will automatically appear on the screen. If the camera is still switched off, an acoustic signal is emitted and appears on the display.

Initial use of parent unit with mains part plug

  1. Connect the small end of the parent mains part plug with the parent unit.
    Insert the other end of the parent mains part plug into a suitable socket.

  2. To switch on the parent unit, press and hold the ON/OFF button on the top for approx. 3 seconds. If the camera is already switched on, the trans-mission image from the camera will automatically appear on the screen. If the camera is still switched off, an acoustic signal is emitted and the following symbol appears on the display:

Usage

Adjusting the volume
The parent unit has 5 volume levels.
To adjust the volume, press the ( – ) or ( + ) button on the side.

Adjusting the brightness
The parent unit has 5 brightness levels.
To adjust the brightness, press the button.

Intercom function
The parent unit has an intercom function.
To activate the intercom function, hold down the button on the parent unit and speak into the unit. The words you have spoken can now be heard on the camera. To deactivate the intercom function, release the button again.

Settings menu
You can adjust the following settings in the menu of the parent unit: zoom function, lullabies, timer, add/delete camera, select camera, noise sensitivity, frequency, energy-saving mode, temperature unit and temperature alarm, movement alarm and resetting to factory settings.

To access the settings menu, switch the parent unit on and press the ( ) button. The following settings menu appears at the bottom edge of the parent unit screen:

Usage 1

You can navigate through the menu using the and the button To exit the settings menu, press and hold the return button.

Zoom function
The parent unit has a zoom function to increase the size of the transmission image. To activate the zoom function, proceed as follows:

  • Press the button.
  • Use the direction buttons to select the zoom factor you want (1x or 2x).
  • Confirm using the ( OK ) button.

Lullabies
Via the parent unit, you can activate one of four lullabies that will then be played over the camera. To activate one of the lullabies, proceed as follows:

  • Press the button.
  • Use the direction buttons to select menu item.
  • Use the direction buttons to select the lullaby of your choice (1, 2, 3, 4 or random ).
  • Confirm using the ( OK ) button.
  • To adjust the volume of the lullabies, press the ( – ) or ( + ) button on the side.

VOX Noise sensitivity setting

The noise sensitivity setting on the baby unit determines what you can hear on the parent unit. If you set the sensitivity level to high (H), you will hear even very quiet noises via the parent unit. If you set the sensitivity level to medium (M), you will hear medium-loud noises via the parent unit. If you set the sensitivity level to low (L), you will only hear very loud noises via the parent unit.

To change the sensitivity level, proceed as follows:

  • Press the button.
  • Use the direction buttons to select menu item .
  • Use the direction buttons to select your desired sensitivity level ( H = high, M = medium or L = low).
  • Confirm using the ( OK ) button.

Useful information about the baby monitor

  • Operating the parent unit with the battery minimises electrosmog from electrical and magnetic alternating fields.
  • You can increase the range of the baby monitor by positioning the camera as high up as possible near a door or window and ensuring that the battery is not too weak.
  • Other radio waves may possibly interfere with the transmission of the baby monitor. Therefore, do not position the baby monitor near devices such as microwaves, WIFI, etc.
  • The following additional factors can interfere with the baby monitor’s transmission or shorten its range: furniture, walls, houses, trees, environmental factors (such as fog, rain).

Cleaning and maintenance

The service life of the camera and the parent unit depend on careful handling.

IMPORTANT

  • Remove the battery from the parent unit if the video baby monitor is not in use for an extended period.
  • You will obtain the maximum capacity from your battery if you run down the battery at least every 6 months. To do this, disconnect the parent unit from the mains and run the battery down through normal use. Afterwards, fully charge the battery again.
  • The maximum capacity of the battery can only be reached after it has been charged multiple times and is dependent on several factors (battery state, ambient temperature, type and frequency of charging, etc
  • Protect the camera and the parent unit from impacts, damp, dust, chemicals, drastic changes in temperature, electromagnetic fields and nearby sources of heat (ovens, heaters).
  • Clean the camera/parent unit with a soft, dry cloth. Do not use any abrasive cleaning products.

Accessories and replacement parts

For replacement parts and additional items visit www.beurer.com or contact the corresponding service address in your country (according to the service address list).
Replacement parts and additional items are also available from retailers.

Replacement parts and additional items Item number
BY 110 single camera 952.63

What if there are problems?

Parent unit will not switch on| Check whether

• the mains part plug is properly plugged in,

• the battery is correctly inserted,

• the battery is full, needs charging or is dam- aged

---|---
An acoustic signal sounds from the parent unit.| Check whether

• the maximum range has been exceeded,

• the mains part plug for the camera is correctly connected,

• the camera is switched on,

• the parent unit battery needs charging.

The parent unit is switched on, but no sounds can be heard| • To set your desired volume on the parent unit, press the ( ) or ( + ) button on the side during operation.
The parent unit switches itself off.| • Recharge the parent unit battery.

• It could be that the parent unit is in energy-saving mode. Check whether the ener- gy-saving mode has been selected in the menu and deactivate it if necessary.

The signal is weak, the connection keeps failing or there is interference| • If another technical device such as a microwave is in the area between the camera and the parent unit, remove the technical device or switch it off

• Check whether other factors, such as trees or similar, are in the area between the camera and the parent unit, and reposition the devices until the parent unit signals a connection

• Check whether the camera and parent unit are within the maximum receiving range

---|---
If no transmission is possible, you have the option to retune the device signals digitally = pairing| 1. Switch on the camera and parent unit

2. Delete the camera in the menu of the parent unit and then set up the camera again as described in the “Adding a camera” section

Set functions do not work as desired| Reset the device to factory state as described “Resetting to factory settings”

Disposal

Batteries must be disposed of through specially designated collection boxes, recycling points or electronics retailers. You are legally required to dispose of the batteries.
For environmental reasons, do not dispose of the device in the household waste at the end of its useful life.
Dispose of the device at a suitable local collection or recycling point in your country. Dispose of the device in accordance with EC Directive – WEEE (Waste Electrical and Electronic Equipment).
If you have any questions, please contact the local authorities responsible for waste disposal.

Technical specifications

Type Digital receiver
Number of channels 21 channels
Frequency 2.4 – 2.483 GHz
Transmission power 13.01 dBm
Display 2.8” LCD
Transmission technology Infrared technology with ECO⁺ mode
Camera dimensions 7.4 x 7.0 x 10.0 cm
Parent unit dimensions 13.0 x 2.1 x 7.2 cm
Camera weight 114 g
Parent unit weight (without battery) 95 g
Battery weight 38 g
Operation Mains part for parent unit (5 V USB/1.5 A) Mains part for baby unit

(5 V USB/1.0 A) Li-ion battery (1800 mAh)
Operation| Mains part for parent unit| Mains part for baby unit
Manufacturer:| Huizhou CY-Power| Huizhou CY-Power
Model no:| CYHA050150 VWEU / UK| CYHA050100 VWEU / UK
Input:| 100 -240 V AC 50/60 Hz| 100 -240 V AC 50/60 Hz
Output:| 5,0 V DC 1,5 A 7,5 W| 5,0 V DC 1,0 A 5,0 W
Average active efficiency| ≥ 77,04 %| ≥ 75,11 %
No-load power consumption| ≤ 0,076 W| ≤ 0,07 W
Battery:|
Capacity| 1800 mAh
Nominal voltage| 3.7 V
Type designation| Lithium-ion
Battery life| Parent unit: 8 hours

(dependent on battery state, ambient temperature, manner and frequency of charging, etc)

We hereby confirm that this product complies with the European RED Directive 2014/53/EU
The CE Declaration of Conformity for this product can be found under: https://www.beurer.com/web/we-landingpages/de/cedeclarationofconformity.php

Warranty
Further information on the warranty and warranty conditions can be found in the warranty leaflet supplied

Beurer GmbH • Söflinger Straße 218 • 89077 Ulm, Germany
www.beurer.comwww.beurer- gesundheitsratgeber.com
www.beurer-healthguide.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals