VIVOSUN X002F2JUV7 24-Inch Heavy Duty Floor Fan Instruction Manual

June 6, 2024
VIVOSUN

VIVOSUN X002F2JUV7 24-Inch Heavy Duty Floor Fan

INTENDED USE

This product is intended for industrial or other commercial applications. Use only with electrical wiring that is in good working order and that meets applicable codes and ordinances. If you have any questions whether your wiring is adequate, consult a qualifed electrician.
While using your fan, you should follow the IMPORTANT INSTRUCTIONS listed below. As part of those instructions, we have used the word “WARN­ING” to indicate the level of hazard: WARNING indicates a hazard which, if not avoided, could resultin injury or death.

IMPORTANT INSTRUCTIONS

As with all electrical appliances, basic safety precautions should always be followed to reduce the risk of electric shock, fire, or injury to persons, including the following precautions:

  • Read all the instructions before using this fan.
  • Use this fan only as described in this manual. Any other use not recom- mended by the manufacturer may cause electrical shock fire or injury to persons.
  • Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
  • Use of extreme caution is necessary when any fan is used by ornear children, disabled persons or pets and whenever the fan isleft operating unattended.
  • Do not place the fan on a small, unlevel, uneven or any surface which might allow fan to tip or fall.
  • For proper operation, fan should be placed on a smooth,non-combusti­ble, level surface.
  • Always unplug fan when not in use, when moving from placeto place, when assembling or disassembling parts, and before cleaning.
  • The use of attachments, not recommended or sold by the manufacturer, may cause hazards.
  • Do not use outdoors.
  • Do not use fan in window. Rain may cause electrical hazard(for non-win- dow models).
  • Do not operate the fan with blade guards or any safety device removed.
  • Avoid the use of extension cords due to risk of fire. If anextension cord must be used, the cord must be minimum 14 AWG and rated not less then 1875 watts.
  • Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or the like.Arrange cord away from traffic area where it will not be tripped over.
  • Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric shock and/or fire hazard. Avoid contact with moving parts.
  • This appliance is not intended for use by persons (includingchildren) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure they do not play with the appliance.

WARNING

– Shock Hazard

Use your fan only in dry environments. This fan is not intended for use in a bathroom, laundry area, or similar locations, or nearsinks, washing machines, swimming pools or other sources of water. Never locate fan where it may fall into a bathtub or other water receptacle. Do not use in damp environments such as flooded basements.

– Hot Surfaces

Do not touch fan motor when in use. This motor is hot when inuse, to avoid burns, do not let bare skin touch hot surfaces.

– Fire Hazard

Fans have arcing or sparking parts inside. Do not use near combustible materials or flammable gases or sources of heat. DO NOT USE in areas where gasoline, paint or flammable materials are used or stored. To prevent a possible fire, do notblock air intakes or exhaust in any manner. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as thismay cause an electric shock, fire, or damage the fan.

– Electrical Shock Hazard

Do not use with damaged cord or plug. Use with adequate electrical system that is up to code.

-To Prevent Electric Shock

This product has a three prong grounded plug that must be inserted into amatching properly grounded outlet to reduce the risk of electrical shock. Do not attempt to defeat this safety feature.

-To Reduce the Risk of Fire or Electric

Do not use this product with any solid-state speed control device.

USAGE

– Fan Operation
Always operate the fan in the upright position following all instructions and recommendations listed in this manual.
– Fan Location
Place the fan in the area of the room that will provide proper fan cooling.
– Fan Connection
Plug fan directly into 120 volt A.C., 60 Hz wall outlet. Be sure plug fits tightly in outlet. A loose connection may cause overheating and damage to the plug or fan.
NOTE : To prevent overloading a circuit, do not plug the fan into a circuit that is servicing other electrical needs.
– Turning Fan On
Place fan on stable level surface. Plug faninto properly grounded outlet. To start the fan, turn the switch from the OFF position to the desired fan speed.
-Turning Fan Off
To turn the fan off, turn the switch from the current fan speed setting to the off position. Remove plug from outlet.
– Adjusting Fan Tilt
To adjust the tilt angle, use supplied knob wrench to loosen the adjustment screw. After adjustment, retighten the adjustment screw. Save knob wrench for future use.

FAN ASSEMBLY

FAN ASSEMBLY

WARNING

– There is one small hole on eachside of the two cradle bases. The two small holes should be kept inner side and at the same directions.
– Castors must be installed before use.

CARE AND MAINTENANCE

– Cleaning

CAUTION-Before cleaning the fan be sure todisconnect power cord from the plug. Clean the grille surface with a clean damp cloth. Do not use harsh chemical or abrasive cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN WATER. Replace front grille before fan use. Allow fan to dry completely before use. Periodic grille cleaning with a vacuum will prevent dust build up. The motor is sealed and does not requireany interior maintenance, cleaning or lubrication.

– Maintenance

The Internal motor bearings are permanently lubricated at the factory and do not require any additional lubrication.

-Repair

DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN ANYWAY.

– Storage

Keep original carton for storage of the fan. Coil and tiethe power cord to avoid damage during storage.
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility forexam­ination and/or repair.

FUSE REPLACEMENT

  • Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
  • Open fuse cover by sliding open fuse access cover on top ofattachment plug towards blades. See Fig. 2.
  • Remove fuse carefully. Use a small tool to pry the end of thefuse from holder cavity. Be careful not to break glass window.
  • Replace fuse. WARNING: Risk of fire. Replace fuse only with identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm). Be sure fuse is properly seated within its cavity.
  • Close fuse cover by sliding it back to its original closed position.

WHY US ?

VIVOSUN X002F2JUV7 24-Inch Heavy Duty Floor Fan fig 4

Designed by VIVOSUN in California

Made in P.R.C

Documents / Resources

| VIVOSUN X002F2JUV7 24-Inch Heavy Duty Floor Fan [pdf] Instruction Manual
X002F2JUV7, 331301-24, 24-Inch Heavy Duty Floor Fan
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals