Knox Gear KN-LAPAS01 Luxor Linear Array PA System User Manual
- June 6, 2024
- Knox Gear
Table of Contents
Knox Gear KN-LAPAS01 Luxor Linear Array PA System
WELCOME!
Dear Knox Gear Customer,
Congratulations on your purchase of the Knox Gear Luxor Linear Array PA
System. To ensure your safety and proper setup, please read this user manual
carefully before using this accessory. Keep the manual in a safe place for
future reference.
The Luxor Linear Array PA System is an all-in-one linear-array PA system
featuring multiple input channels with individual tone controls, reverb, and
Bluetooth audio streaming, allowing you to integrate the system with any
number of audio spaces and still look great. Designed to store all components
in one unit for a one-hand carry, the Luxor Linear Array PA System is perfect
for situations where ease and portability are just as important as high-
quality sound.
We hope you enjoy your new Knox Gear Luxor PA System. Sincerely, The Knox Gear
Tea For technical assistance, please email us at
cs@knoxgear.com.
SAFETY INSTRUCTIONS
-
Read and keep these instructions safe. Heed all warnings and follow all instructions.
-
Do not use this device near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings.
-
Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Do not bypass the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician.
-
Take caution not to walk on or pinch the power cord, especially where it connects to the device and outlet.
-
Only use attachments/accessories specified by the manufacturer.
-
Only use with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the device. When a cart is used, use caution when moving the cart/device combination to avoid injury from tip-over.
-
Unplug this device during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, including damage to power supply cord or plug, water/moisture damage, objects have fallen into the device, the device does not operate normally, or it has been dropped.
CAUTION : These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any service other than those specified in the instruction manual. To completely disconnect this device from the AC mains, disconnect the power supply cord plug from the AC receptacle.
WARNING: To reduce the risk of fire of electric shock, do not expose this device to rain or moisture. -
Do not expose this device to any water dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the device.
WARNING: The mains plug/appliance coupler is used to disconnect device, the disconnect device shall remain readily operable. -
Protective earthing terminal: the device should be connected to an outlet with a protective earthing connection.
Correct disposal of this product: to prevent possible harm to the environment or human health from uncontrolled waste disposal, this product should not be disposed with household waste. Recycle the device responsibly to promote the sustainable reuse of material resources. -
Do not place any naked flames near the device, including candles.
-
For adequate ventilation, do not place this device in a confined or enclosed space, such as a bookcase or
similar unit. Product ventilation should not be impeded
by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc. -
Wait until the system is fully turned on and the menu appears before turning off the power. The system will make a noise otherwise, but this does not indicate damage.
The Knox Gear Luxor Linear Array PA System is not intended for use in high
moisture environments. Moisture can damage the speaker cone and surround and
cause corrosion of electrical contacts and metal parts. Avoid exposing the
speakers to direct moisture. Keep speakers out of extended or intense direct
sunlight. The driver suspension will prematurely dry out and finished surfaces
may be degraded by long-term exposure to intense ultraviolet (UV) light.
The Knox Gear Luxor Linear Array PA System can generate considerable energy.
When placed on a slippery surface such as polished wood or linoleum, the
speaker may move due to its acoustical energy output. Precautions should be
taken to assure that the speaker does not fall off a stage or table on which
it is placed. Hearing Damage, Prolonged Exposure to Excessive SPL The Knox
Gear Luxor Linear Array PA System can generate sound pressure levels (SPL)
strong enough to cause permanent hearing damage. Caution should be taken to
avoid prolonged exposure to SPL in excess of 90dB.
CLEANING & CARE
Knox Gear Luxor Linear Array PA System may be cleaned with a dry cloth. Take care not to get moisture inside the device. Ensure that the system is unplugged from the outlet before cleaning. This system contains potentially lethal voltages. To prevent electric shock or hazard, do not remove chassis, mixer module, or AC input covers. Refer all service to qualified service personnel.
PACKAGE CONTENTS
- Knox Gear Luxor Linear Array PA System Base
- 2 x Listening Height Spacers
- Column Speaker Array
- Power Cable
- User Manual
ASSEMBLY INSTRUCTIONS
- Remove the Knox Gear Luxor Linear Array PA System from the carton.
- Remove the spacers and column speaker array from the carton.
- Place spacers for desired listening level then attach the column speaker array. Note: The spacers are not required for use. You can assemble without the spacers.
- Connect the female end of the power cable to the mixer and plug the male end into your wall socket or an extension cord. Turn the Master Volume control all the way to the left.
- Turn the power switch to the “On” position. The Power LED Indicator should now be on.
- At this point the Luxor is ready for use. You may adjust the channel and master volume controls and play audio.
CONTROL PANEL
The Control Panel houses the mixing board and power amplifier, where
microphones and external sound sources are connected. A mixing board channels
audio sources in through the inputs and routes the signal to the outputs
(Master Volume or Line Out). The mixer controls enable you to control the tone
and volume, in addition to routing the signal and adding reverb to individual
input sources.
-
CH1 Volume Knobs: Use this knob to adjust the volume levels for CH1.
-
CH2 Volume Knobs: Use this knob to adjust the volume levels for CH2.
-
CH1 Mic/Line Input Selector: When CH1 is connected to a microphone, press this button to select Mic mode. When CH1 is connected to a line input, release this button to select Line mode.
-
CH2 Mic/Line Input Selector: When CH2 is connected to a microphone, press this button to select Mic mode. When CH2 is connected to a line input, release this button to select Line mode.
-
CH1 Input: 1/4” jack connector input.
-
CH2 Input: 1/4” jack connector input.
-
CH3 Input: XLR/1/4” jack combo connector input.
-
CH4/5 Input: RCA jack connector input.
-
LINE OUT: XLR connector output.
-
CH3 Mic/Line Input Selector: When CH3 is connected to a microphone, press this button to select Mic mode. When CH3 is connected to a line input, release this button to select Line mode.
-
CH3 Volume Knobs: Use this knob to adjust the volume levels for CH3.
-
CH4/5 Volume Knobs: Use this knob to adjust the volume levels for CH4/5.
-
CH4/5 Input: 3.5mm jack connector input.
-
DSP Menu/Volume Knob: Rotate to adjust the volume. When the device is turned off and then back on, the volume will remain the same as it does not change when the device is turned off. Press once to enter the DSP menu (please refer to the
“Operating the DSP Menu” section starting on page 12 for details). -
Vocal Cut Button: press once to select ON/OFF. When
it is on, the vocals will be cut. (Note that this is only an entertainment function, and the voice volume is lowered, but cannot be completely eliminated.) -
Signal Indicator Light: Green (Standby)/Flashing Green (Playing)/Flashing Red (Limit).
-
Microphone Effect Button – there are 4 microphone effects:
- Reverb: ON+ECHO: ON
- Reverb: ON+ECHO: OFF
- Reverb: OFF+ECHO: ON
- Reverb: OFF+ECHO: OFF
-
EQ Button: There are 6 equalizer (EQ) settings. The EQ chosen is automatically remembered after shutdown and will remain the same when next in use.
- Music (i.e. standard setting)
- Classic (i.e. classical music setting)
- Pop
- Rock
- Jazz
- Country
-
Press once to skip to the next song or FM channel.
-
Press once to skip to the previous song or FM channel.
-
Repeat Button – there are 4 modes:
- Repeat One
- Random
- Repeat Folder
- Repeat All
-
LED Display
-
Input Mode: Use this button to select LINE IN, BLUE
(Bluetooth), FM, or MP3 player mode. -
In MP3 mode, press once to play or pause song. In FM mode, press once to scan and find radio stations. They will be saved automatically.
-
USB Port: Allows you to insert a USB device with MP3 files.
-
SD Port: Allows you to insert an SD card with MP3 files.
-
110V – 220V Selector
-
ON/OFF Power Switch
-
AC Power: Port for connecting the AC power cord.
Master Volume & Signal Limit
The Luxor Linear Array PA System is equipped with a Master Volume regulator
that controls the overall output volume of the system and a yellow LED that
indicates that maximum volume has been reached.
Audio Inputs
The Luxor Linear Array PA System has 5 inputs: All the inputs will route to
the speakers and to the Line Out. The Luxor Linear Array PA System also
includes Bluetooth audio streaming.
- Channels 1 & 2: 1/4” inputs
- Channel 3: XLR/1/4” Combo input
- Channels 4 & 5: RCA Jack Connector and Aux (3.5 mm) inputs
Line Out
Line out is an XLR connector output that allows you to connect the Luxor PA
System to another system of your choosing, such as another mixer or other
speakers.
OPERATING THE DSP MENU
The digital signal processing (DSP) menu allows the user to customize the
settings of the Luxor Linear Array PA System. NOTE: (*) denotes automatic
memory after shutoff, meaning the setting will be remembered after the system
is turned on.
On the start interface:
- Press the DSP/Volume knob to enter the menu.
- After entering the menu, turn the knob to select the submenu.
Music
- Press the knob to access the Music submenu.
- After accessing the submenu, press the knob to select items in downward sequence (it will proceed through the menu one by one; if you need to reset, access the submenu again).
- After making a selection, turn the knob to set.
- Volume: System volume [0~32] (*)
- Bass: Music bass [-12db~+12db]
- Treble: Music treble [-12db~+12db]
- EQ: Music EQ setting (see page 10)
- Vocal Cut: Eliminates the human voice in the music [OFF/ON]
- Music 3D: 3D surround sound [OFF/ON] (*)
- Sub: Strengthens bass [OFF/60Hz/80Hz/120Hz]
- Exit: Return to previous menu
NOTE:
Bass and treble can only be adjusted from the default “Music” EQ setting.
Attempting to adjust the bass or treble from another EQ setting will revert
the EQ to “Music”. Manual EQ settings are never saved; switching to a
different EQ will reset any adjustments. Values are also reset when the system
is shut off; treble and bass settings have no auto memory.
Microphone
- Press the knob to access the Microphone submenu.
- After accessing the submenu, press the knob to select items in downward sequence (it will proceed through the menu one by one; if you need to reset, access the submenu again).
- After selecting the item, turn the knob to set.
- Volume: Microphone volume [0~32] (*)
- Bass: Microphone bass [-12db~+12db] (*)
- Treble: Microphone treble [-12db~+12db] (*)
- Echo: Microphone echo [50ms/100ms/150ms/200ms/250ms /300ms/350ms/400ms/450ms/500s/550ms/600ms] (*)
- Reverb: Microphone reverb [0~32] (*)
- Exit: Return to previous menu
System
- Press the knob to access the menu.
- After accessing the submenu, press the knob to select items in downward sequence (it will proceed through the menu one by one; if you need to reset, access the submenu again).
- After selecting the item, turn the knob to set.
- Contrast: Screen brightness [0~15] (*)
- Backlight: Screen backlight display time (minutes) [0m (backlight is always on)/1m/5m/10m/30m] (*)
- Version: DSP system version
- Exit: Return to previous menu
TECHNICAL SPECIFICATIONS
System
- System Type: Portable Line Array with powered mixer
- Maximum SPL Output: 118 dB peak system output
- Frequency Range (-10dB): 37.5Hz – 18.5kHz
- Frequency Response (-3dB): 45Hz – 18kHz
- AC input: AC110V~60Hz/AC220V~50Hz
Amplifier
- Design: Class D
- System Power Rating: 150 Watts LF+ 150 Watts HF
Speaker
- LF Driver: 8” subwoofer
- HF Driver: 4 x 2.5” Full range speaker
- Coverage Pattern: 100 degrees x 50 degrees nominal
Dimensions (H x W x D)
- Packaged Dimensions: 18.9” x 18.1” x 21.9”
WARRANTY
Knox Gear offers a 1-year Guaranteed Good: Works As It Should warranty, covering both parts and labor to ensure that you enjoy the full use of this product with peace of mind. For more information about your warranty, please contact Customer Service at cs@knoxgear.com.
Questions?
Please contact Customer Service at cs@knoxgear.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>