ideal lux Flut SP1 Big Suspension Lamp Instruction Manual

: June 21, 2024
: ideal lux

Table of Contents

ideal lux Flut SP1 Big Suspension Lamp
Product Specifications
Product Usage Instructions
Frequently Asked Questions
Dimension
FEATURES
SAFETY INSTRUCTIONS
Documents / Resources

ideal lux Flut SP1 Big Suspension Lamp

Product Specifications

Model: Flut SP1 Big
Socket Type: E27
Max Wattage: 1 x 60W
Voltage: 220~240V 50/60Hz
Color Options: BIANCO (White), NERO (Black)
Barcode: 8021696035666 (BIANCO), 8021696035680 (NERO)

Product Usage Instructions

Installation

Follow the assembly instructions by reading the numerical progression. The lighting fitting should be installed by a qualified electrician.

Safety Instructions

The installation must be completed by a qualified electrician.
Always disconnect the power supply before starting installation or any maintenance work.
The luminaire has parts that can get hot, and are handled with care.
Use appropriate fixing accessories for each type of material; only use compliant screws and plugs.
The light source uses non-replaceable LEDs; do not dismantle the source.
If the lamp does not turn on, replace the fuse.
Mandatory grounding is required for electrical safety.

Electrical Safety Classes

Class I: Main insulation and protective conductor (grounding) connected to the metal structure of the lamp. Mandatory grounding is required.
Class II: Double or reinforced insulation with no grounding required.
Class III: Safety ensured by very low voltage (less than 50 Volts) with no grounding required.

Protection Ratings

IP0… to IP8: Protection against solid objects and dust ingress based on specific diameters.

Frequently Asked Questions

Q: Can I replace the LEDs in the light source?

A: No, the LEDs are non-replaceable. Do not attempt to dismantle the light source.

Q: What should I do if the lamp does not turn on?

A: If the lamp does not turn on, try replacing the fuse with a new one.

Q: Is grounding mandatory for this product?

A: Yes, grounding is mandatory for electrical safety, especially for Class I electrical safety.

Dimension

Suspension lamp

Suspension
E27 max 1 x 60W / 220~240V 50/60Hz
8021696035666 BIANCO
8021696035680 NERO

FEATURES

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION. THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

SAFETY INSTRUCTIONS

This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor, or by a qualified electrician.
Always isolate power before commencing installation, maintenance, or repair.
The luminaire contains certain parts which can be very hot.
Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
Always tighten the screws firmly to avoid contact problems.
This fitting should only be installed indoors.
Luminaires were not suitable for recessed on normally flammable surfaces.
The luminaire was not suitable for direct mounting on normal flammable surfaces.
This fitting is only suitable for fixing the ceiling.
This fitting is only suitable for fixing the wall.
The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
Only use lamps that do not exceed the maximum specified wattage.
Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
Class | Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
Class IL electrical safety is guaranteed by the main insulation and double or reinforced insulation.
- Earthing is not necessary.
Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volt). Earthing excluded.
Not protected.
Protected against solid objects greater than 50 mm.
Protected against solid objects greater than 12 mm.
Protected against solid objects greater than 2,5 mm.
Protected against solid objects greater than 1mm.
Dust protected.
Totally protected against dust infiltration.
Not protected.
Protected against vertically falling water drops.
Protected against water drops falling with a maximum angle of 15° to the vertical axis.
Protected against rain.
Protected against splashing water.
Protected against water jets.
Protected against strong water jets.
Protected against temporary immersion.
Protected against prolonged immersion.
The luminaire was not suitable for covering with thermally insulating material.
Caution, risk of electric shock.
Do not stare at the operating light source.