ZEVNI A04696 Mavis 14.1-in 2-Light Black-Brass Transitional Vanity Light Instruction Manual
- June 9, 2024
- ZEVNI
Table of Contents
ZEVNI A04696 Mavis 14.1-in 2-Light Black-Brass Transitional Vanity Light
Item Number
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- B) Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Screw (4)
- (G) Arm (1)
- (H) Socket (2)
- (I) Glass shade (2)
- (J) Socket ring (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- A) Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- B) Place the wall switch in the “OFF” position.
- Make assembly
- Step A1: Unscrew screws (F) from back plate (E), then set them aside for later installation.
- Step A2: Carefully pass the supply wires from the outlet box through mounting plate (D).
- Secure mounting plate (D) to the outlet box with mounting screws (A).
- Step A3: Make wire connections
- Step A4: Position back plate (E) and mounting plate (D) in place, carefully thread screws (F) through the holes in back plate (E) and mounting plate (D). Secure them by tightening screws (F).
- Step A5: Unscrew socket rings (J) from sockets (H).
- Place glass shades (I) on sockets (H) and secure them with socket rings (J).
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
Connect ground wires according to the below chart
Connect wires according to the below chart
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and nonabrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive
paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>