ASKEY 8822CS WiFi BT Combo Module User Manual
- June 6, 2024
- ASKEY
Table of Contents
Dimension | LxWx H: 15 x 13 x 2.15 mm (typical) |
---|---|
Wi-Fi Interface | Support SDIO V3.0 |
BT Interface | UART/PCM |
Operating temperature | 0°C to 70°C |
Storage temperature | -40°C to 85°C |
Features
Highly integrated wireless local area network(WLAN) system-on-chip (SOC) for 5
GHz 802.11ac, or 2.4G/5G 802.11n WLAN applications.
Dual-stream spatial multiplexing up to 867 Mbps data rate.
Supports 20/40MHz at 2.4GHz and supports 20/40/80MHz at 5GHz
Supports low power SDIO3.0 interface for WLAN and UART/PCM interface for
Bluetooth.
Supports the Bluetooth V5.0 system.
Supports WLAN-Bluetooth coexistence.
BT host digital interface:
– HCI UART (up to 4 Mbps)
– PCM for audio data
The module has 2 antenna ports, a BT port combined with WLAN1.
Block Diagram:
Wi-Fi RF Specification
2.4GHz RF Specification
Frequency Range:| 802.11b/g/n-HT20: 2412 – 2462MHz 802.11n-HT40: 2422 –
2452MHz
---|---
Channel Number:| 802.11b/g/n-HT20: 11 802.11n-HT40: 7
Type of Modulation:| 802.11b: DSSS 802.11g/n: OFDM
Data Rate:| 802.11b: 1/2/5.5/11Mbps
802.11g: 6/9/12/18/24/36/48/54Mbps
802.11n: up to 300Mbps
5GHz RF Specification
Frequency Range:| For 802.11a/n-HT20/ac-VHT20: 5180-5240MHz, 5260-5320MHz,
5500-5720MHz, 5745-5825MHz
For 802.11n-HT40/ac-VHT40: 5190-5230MHz, 5270-5310MHz, 5510-5710MHz,
5755-5795MHz
For 802.11ac-VHT80: 5210MHz, 5290MHz, 5530MHz, 5610MHz, 5690MHz, 5775MHz
---|---
Type of Modulation:| 802.11a/n/ac: OFDM
Data Rate| 802.11a: 6/9/12/18/24/36/48/54Mbps
802.11n: up to 300Mbps
802.11 ac: up to 866.6Mbps
Note: The frequencies that fall in the 5600MHz to 5650MHz band will not be used in Canada.
Bluetooth Specification
Operating Frequency: | 2402-2480MHz |
---|---|
Channel Number: | BR/EDR: 79 BLE: 40 |
Type of modulation: | GFSK, Pi/4 DQPSK, 8DPSK |
Data Rate: | 1Mbps, 2Mbps, 3Mbps |
Antenna Specification
Antenna Type| Frequency Band (GHz)| Tx Paths| Per Chain Max
Antenna Gain (dBi)| Directional Gain (dBi)
---|---|---|---|---
Ant 0| Ant 1| For Power| For PSD
Wi-Fi Internal Antenna
PIFA| 2412 – 2462| 2| 2.1| 1.9| 2.1| 5.11
5180 – 5240| 2| 4.2| 1.9| 4.2| 7.21
5260 – 5320| 2| 3.8| 3.0| 3.8| 6.81
5500 – 5720| 2| 3.8| 2.9| 3.8| 6.81
5745 – 5825| 2| 3.4| 2.3| 3.4| 6.41
Bluetooth Internal Antenna
PIFA| 2402 – 2480| 1| 1.9| —
Dimensions
Marking Description
Label
The Key Material List
Main | Inductor | 2012 1uH. ± 20°/0.0.8A,LON121PN1ROMCO (MURATA ) |
---|---|---|
Alt | Inductor | 2012 1.5uH , -±- 20%. 1A al. MGFL2012F1R5MT-LF |
Alt | Inductor | 2016 1.5uH, + 20%, 800mA MPIE201610-1R5M-LF |
Main | Diplexer | RFDIP160806BLM6T25 |
Alt | Diplexer | DPX166000DT-8093A1.1.6*0.8mm,6PIN (TDK) |
Alt | Diplexer | LD18D2450LAN-040/M (GILEAD) |
Main | Shielding | |
cover | RTL8822CS Copper, without positioning the foot | |
Main | Crystal | 2520 40MHz 10ppm 12pF E2SB40,0000F12G11RE (HOSONIC) |
Alt | Crystal | 2520 40MHz 10ppm 12PF -20-85° C Q40000E0870740 |
Main | Chipset | RTL8822CS-VS-CG 9X9mm |
Recommended Reflow Profile
Package Information
Moisture sensitivity
The Modules is a Moisture-Sensitive Device-level 3, in accordance with standard IPC/JEDEC J-STD-020, take care of all the relative’s requirements for using this kind of components.
Moreover, the customer has to take care of the following conditions:
a) Calculated shelf life in sealed bag: 12 months at <40°C and <90% relative
humidity (RH).
b) Environmental condition during the production: 30°C / 60% RH according to
IPC/JEDEC J-STD-033A paragraph 5.
c) The maximum time between the opening of the sealed bag and the reflow
process must be 168 hours if the condition
b) “IPC/JEDEC J-STD-033A paragraph 5.2” is respected
d) Baking is required if conditions b) or c) are not respected
e) Baking is required if the humidity indicator inside the bag indicates 10%
RH or more
U.S. FCC Statement
FCC ID: H8N-8822CS
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located
or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
Canada (IC) Notices
IC: 1353A-8822CS
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada license-exempt RSS. Operation is
subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Caution:
The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator & your body.
OEM Integration Instructions:
This device is intended only for OEM integrators under the following
conditions: The module can be used to install in another host. The antenna
must be installed such that 20 cm is maintained between the antenna and users,
and the transmitter module may not be co-located with any other transmitter or
antenna. The module shall be only used with the integral antenna(s) that has
been originally tested and certified with this module. As long as the 3
conditions above are met, further transmitter tests will not be required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirement with this module installed (for
example, digital device emission, PC peripheral requirements, etc.)
IMPORTANT NOTE: In the event that these conditions cannot be met (for
example certain laptop configuration or co-location with another transmitter),
then the FCC authorization for this module in combination with the host
equipment is no longer considered valid and the FCC ID of the module cannot be
used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating. The end product (including the transmitter) and
obtaining a separate FCC authorization. The final end product must be labeled
in a visible area with the following: “Contains Transmitter Module FCC ID:
H8N-8822CS or Contains FCC ID: H8N-8822CS”.
Antenna Specification:
Antenna Type| Frequency
Band
(GHz)| Tx
Paths| Per Chain Max
Antenna Gain (dBi)| CDD Directional Gain
(dBi)
---|---|---|---|---
Ant 0| Ant 1| For Power| For PSD
Wi-Fi Internal Antenna
PIFA| 2412 — 2462| 2| 2.1| 1.9| 2.1| 5.11
5180 — 5240| 2| 4.2| 1.9| 4.2| 7.21
5260 — 5320| 2| 3.8| 3.0| 3.8| 6.81
5500 — 5720| 2| 3.8| 2.9| 3.8| 6.81
5745 — 5825| 2| 3.4| 2.3| 3.4| 6.41
Bluetooth Internal Antenna
PIFA| 2402 — 2480| 1| 1.9|
IMPORTANT NOTE:
This Wireless Module (IC: 1353A-8822CS) has been approved by Industry Canada
to operate with the antenna types listed below with the maximum permissible
gain indicated. Antenna types not included in this list, having a gain greater
than the
maximum gain indicated for that type, are strictly prohibited for use with
this device.
The Host Marketing Name (HMN) must be displayed (according to e-labeling
requirements) or indicated at any location on the exterior of the host product
or product packaging or product literature, which shall be available with the
host product or online.
The host product shall be properly labeled to identify the modules within the
host product. The Innovation, Science and Economic Development Canada
certification label of a module shall be clearly visible at all times when
installed in the host product; otherwise, the host product must be labeled to
display the Innovation, Science and Economic Development Canada certification
number for the module, preceded by the word “Contains” or similar wording
expressing the same meaning, as follows:
Contains IC: 1353A-8822CS.
Antenna Specification:
Antenna Type| Frequency Band (GHz)| Tx Paths| Per Chain Max
Antenna Gain (dBi)| CDD Directional Gain (dBi)
---|---|---|---|---
Ant 0| Ant 1| For Power| For PSD
Wi-Fi Internal Antenna
PIFA| 2412 — 2462| 2| 2.1| 1.9| 2.1| 5.11
5180 — 5240| 2| 4.2| 1.9| 4.2| 7.21
5260 — 5320| 2| 3.8| 3.0| 3.8| 6.81
5500 — 5720| 2| 3.8| 2.9| 3.8| 6.81
5745 — 5825| 2| 3.4| 2.3| 3.4| 6.41
Bluetooth Internal Antenna
PIFA| 2402 — 2480| 1| 1.9|
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>