CLEERLINE SSF-SFP-RJ45-1G Gigabit Fiber Media Converters Instruction Manual

SSF-SFP-RJ45-1G / SSF-SFP-SFP-CON
Gigabit Fiber Media Converters
Manual

www.cleerlinefiber.com

GIGABIT FIBER MEDIA CONVERTERS

Ordering Information

SSF-SFP-RJ45-1G Gigabit Media Converter 10/100/1000Base-Tx to 100/1000Base-X SFP slot, DIP SW config., AC adapter included
SSF-SFP-SFP-CON multi-rate Media Converter SFP slot to SFP slot, DIP SW config., AC adapter included

Overview

These Gigabit Ethernet fiber media converters provide high performance and reduced size. Units have DIP switches for custom speed and flow settings for strong networking flexibility. Physical dimensions have been reduced for minimum footprint and highest density attainable in a 19″ rack environment: 12 units/RU. Reliability is highly ranked with an MTBF exceeding 65,000 hours. Converters support IEEE802.3u IEEE802.3z 1000Base-TX/FX protocols. The package includes AC adapter 100-240V to DC 5V and one User Manual.

Features

• 10/100/1000Base-T to 100/1000Base-X Conversion (or same rate transparent for SSF-SFP-SFP-CON model)
• Auto-Negotiation and Auto MDI/MDIX (LFC-1001/1002-SFP)
• Forward 2048 bytes (Max.) packets in switch mode (copper & fiber port in different speeds)
• Forward 9k bytes in converter mode (fiber & copper port at the same speed)
• DIP switch settings for fiber speed (100/1000M), LPF, and Flow control
• Support for Q in Q double tagged frame transparent
• Support for IEEE 802.1Q Tag VLAN pass-thru
• 100M to 2.5G transparent O-E-O repeater – both optical ports must have the same rate (model SSF-SFP-SFP-CON)
• Installs into high density 12 slot/1RU rack-mountable chassis (with options of redundant and AC or DC48 power supplies)

DIP Switch Settings

| MODEL| SSF-SFP-SFP-CON
---|---|---
DIP| Function| Settings
SW 1| LFP| OFF – Disabled| ON – Enabled
SW 2| Forwarding Mode| OFF/OFF
OFF/ON| Store & Forward
Cut-Through
SW 3| (paired setting 2&3)| ON/OFF
ON/ON| Smart Pass-Through
Pass-Through
SW 4| FX port 100M mode| OFF – 1000M| ON – 100M

| FUNCTION
---|---
TP/LNK| Off – No link; On – RJ45 link OK; Blinking – data traffic present
SPD| Off – 10M/100M; On – 1000M on RJ45 port
FX/LNK SFP1 SFP2| Off – No link; On – Fiber link OK; Blinking – data traffic present
PWR| Off – No power available; On – Power is present

Installation

1. Choose a flat secure surface with room for proper ventilation.
2. Power up the unit using the included AC adapter. Observe PWR LED status indicating proper power to the unit.
3. Connect RJ45 UTP port using Cat5e or better cable to another Ethernet device. Make sure the TP LED indicates proper connectivity.
4. Insert a Gigabit or Fast Ethernet-rated SFP transceiver into the SFP slot. Make sure the fiber transceiver used matches the fiber type (MM or SM) and also matches a similar optical transceiver at the other end of the fiber. Inspect FX LED for proper fiber link status.

Troubleshooting

1. No TP/LNK light: verify proper UTP cabling/pinout.
2. No FX/LNK light: verify fiber connectivity and fiber type. Consider cleaning up fiber connectors and SFPs with appropriate tools. Make sure Tx and RX ports are properly crossed between units. Make sure FX speed is properly set on DIP SW.
3. No PWR light: Use only the AC adapter included. Make sure AC power is available

Technical Specifications

AC frequency: 50-60Hz, Output DC 5V/1A
Power Requirements| 5DC 5-12V, 4W max. power consumption
Dimensions| 90mm x 60mm x 20mm (SFP not included)
| Wall or shelf (optional bracket needed)
Environmental Conditions|  Operating Ambient Temperature: 0 to 50°C
Operating Humidity: Maximum 85%, Noncondensing Storage
Temperature: -30 to 70°C
Storage Humidity: Maximum 95%, Non-condensing
Indoor rated operating device
MTBF| 65,000 hours

Warning

1. Use only indoors in a climate-controlled environment.
2. Avoid looking directly into fibers or lasers while the unit is powered.
3. Use only the AC adapter included with the unit (or with the LFC series chassis available separately)

FCC and CE markings

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

This is a CE class B device, intended to be used in residential, commercial or industrial applications.

References

• Home - Cleerline SSF Fiber

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>