Askey Computer TN230A2 TurboMate E2 Smartwatch User Guide
- June 5, 2024
- Askey Computer
Table of Contents
Askey Computer TN230A2 TurboMate E2 Smartwatch
Package
- TurboMate E 2 device
- Type C USB Cable
- Plug + Adapter (5.35 V/ 2 A)
- Wrist Band with 2 size of length
Product View
-
Front view
Charging Connector:
The charging connector slot should put properly and touch pogo pins on the charging base.
-
Rear View
BIO Sensor
( The function of the BIO sensor is to detect the heart rate. It should be touched well with wrist when wearing with the wrist band.
Wearing Wrist Band
- Bond with the clip-on device
- Release by using the latch of band
Multiple slot charger (Model: DS40310 Slide device from the top of cradle
Pogo Pin:
When charging, the pogo pin on the charger should be snapped properly with the
charging connector on the device.
LED indicator:
LED red) is enlightened while power in.
DC
in the adaptor Plug DC into the DC-in connector for charging. Please use the
adaptor (2A/ 12V) which is included the package. 
Option: Wall Mount
Mounted on the wall by using screw kit M3.5*20L, P head) which is included the
package.
Then slide the cradle from the front and fix the location.
Boot the device
Press the Power key for a few seconds and the device will boot up.
Shut down the device
Press the Power key and hold for few second to see the power off screen shows
up. You can choose “power off” or “Restart” the device.
Home Screen (please slide from right to LEFT}
When slide down from the top of the screen, you can see the
status bar to indicate:
App Screen (Slide from bottom to
top can enter app
Function n description: “Back” in screen means Back/Esc”)
Charging indicator
Caution
- If the device runs out of battery (can’t boot up), please charge the USB cable ( by using the adaptor in the TN230Ax package )). When starting charging, the device will boot up automatically.
- In some cases, if the device crash or hang on a certain screen, please press the power key until feeling the vibration from the device then the device will be hard reset.
- Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Regulatory Information
Caution: Only use TURBONET-approved accessories.
Battery Safety
- The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a noncommercial environment.
- Follow battery usage, storage, and charging guidelines found in the user guide.
- Improper battery use may result in a fire, explosion, or another hazard.
- To charge the device battery, the battery and charger temperature must be between 0 C~+ 45 C.
- Do not use incompatible batteries and chargers. The use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or the
- Do not disassemble or open, crush, bend or deform, puncture, or shred.
- The severe impact of dropping any battery-operated device on a hard surface could cause the battery to overheat.
- Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
- Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire explosion, or another hazard.
- Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place the battery into a microwave oven or dryer.
- Battery usage by children should be supervised.
- Please follow local regulations to promptly dispose of used rechargeable batteries.
- Do not dispose of batteries in a fire.
- Seek medical advice immediately if a battery has been swallowed. In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. I f contact has been made, wash the affected area with large amounts of water and seek medical advice.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two co nditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a CLass
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, i f not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
The product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. Further RF
exposure reduction can be achieved if the product can be kept as far as
possible from the user body or set the device to lower output power if such
function is available.
Note: The country code selection is for non-US models only and is not available to all US models. Per FCC regulation, all WiFi products marketed in US must be fixed to US operation channels only.