EBYTE E10-915MS20 S14463 915MHz 100mW SMD Wireless Module User Manual

EBYTE E10-915MS20 S14463 915MHz 100mW SMD Wireless Module

Disclaimer
EBYTE reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or any part thereof without the express permission of EBYTE is strictly prohibited. The information contained herein is provided “as is” and EBYTE assumes no liability for the use of the information. No warranty, either express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose of the information. This document may be revised by EBYTE at any time. For most recent documents, visit www.ebyte.com.

Overview

Brief introduction
E10-915MS20 is small SMD wireless module working at 915MHz developed based on chip SI4463 from Silicon Labs
Due to the use of the imported Si4463 as the core of the module, its stability has been well received by users, and compatibility is not a concern. The module is aimed at smart home, wireless meter reading, scientific research and medical, and medium and long distance wireless communication equipment. Since RF performance and component selection are in accordance with industrial standards, and the product has obtained FCC, CE, RoHs and other international authoritative certification reports, users do not need to worry about its performance. With its stable

and reliable characteristics, it is favored by the majority of users. Compared with the old products, it has made great progress in receiving current, receiving sensitivity, transmitting power, receiving rate range and anti- interference ability. High precision 26MHz crystal is used. Since the module is a pure RF transceiver module, you need to use the MCU driver or a dedicated SPI debug tool.

Features

•  Communication distance tested is up to 2km
•  Maximum transmission power of 100mW, software multi-level adjustable；
• Support the global license-free ISM 915MHz band；
• Support air date rate of 1.2kbps～1000kbps；
• Support multiple modulation methods, (G)FSK, 4(G)FSK, (G)MSK，OOK ；
• Support 64/128 byte Transceiver Data Register (FIFO)
• Support 2.5V~3.6V power supply, power supply over 3.3 V can guarantee the best performance；
• Industrial grade standard design, support -40 ~ 85 °C for working over a long time；
• IPEX and stamp hole optional, good for secondary development and integration.

Application

• Home security alarm and remote keyless entry；
• Smart home and industrial sensors；
• Wireless alarm security system；
• Building automation solutions；
• Wireless industrial-grade remote control；
• Health care products；
• Advanced Meter Reading Architecture(AMI)；
• Automotive industry applications.

Specification and parameter

Limit parameter

Main parameter

| Performance|

Remark

---|---|---
Min.| Max.

Power supply（V）

|

0

|

3.6

| Voltage over 3.6V will cause permanent

damage to module

Blocking power（dBm）

|

–

|

10

| Chances of burn is slim when modules are

used in short distance

Operating temperature（℃）| -40| 85| /

Operating parameter

Main parameter

| Performance|

Remark

---|---|---
Min.| Typ.| Max.
Operating voltage（V）| 1.8| 3.3| 3.6| ≥3.3 V ensures output power

Communication level（V）

|  |

3.3

|  | For 5V TTL, it may be at risk of burning

down

Operating temperature（℃）| -40| –| 85| Industrial design
Operating frequency（MHz）| 900| 915| 925.5| Support ISM band
Power consumpti

on

| TX current（mA）|  | 98|  | Instant power consumption
RX current（mA）|  | 16|  |
Sleep current （μA）|  | 0.4|  | Software is shut down
Max Tx power（dBm）| 19| 20| 21|
Receiving sensitivity（dBm）| -121| -122| -124| Air data rate is 1kbps
Air data rate（bps）| 0.123k| –| 1M| Controlled via user’s programming
Main parameter| Description| Remark
---|---|---

Distance for reference

|

2000m

| Test condition：clear and open area, antenna gain: 5dBi，

antenna height: 2.5m，air data rate: 1kbps

FIFO| 64Byte| Max length transmitted each time
Crystal frequency| 26MHz|
Modulation| GFSK(recommended)| (G)FSK, 4(G)FSK, (G)MSK，OOK
Package| SMD|
Connector| 1.27mm|
Communication interface| SPI| 0-10Mbps
Size| 15*20 mm|
Antenna| IPEX/stamp hole| 50 ohm impedance

 Size and pin definition

2

| ****

VCC

|  | Power supply ：1.8~ 3.6 V DC, 3.3V is recommended，ceramic filter capacitor can

be added

3| GPIO0| output| GPIO（see more from SI4463 datasheet）
4| GPIO1| output| GPIO（see more from SI4463 datasheet）
---|---|---|---
5| IRQ| output| SPI interrupt request
6| SCK| input| Serial Clock Input
7| MISO| output| SPI master input slave output
8| MOSI| input| SPI master output slave input
9| nSEL| input| SPI Chip select for starting SPI communication

10

| ****

SDN

|  | Shutdown Input Pin. It is low level when working

(See SI4463 manual for more details)

11| ANT|  | Antenna
12| GND|  | Ground

Basic operation

Hardware design

• It is recommended to use a DC stabilized power supply. The power supply ripple factor is as small as possible, and the module needs to be reliably grounded.；
• Please pay attention to the correct connection of the positive and negative poles of the power supply. Reverse connection may cause permanent damage to the module；
• Please check the power supply to ensure it is within the recommended voltage otherwise when it exceeds the maximum value the module will be permanently damaged；
• Please check the stability of the power supply, the voltage can not be fluctuated frequently；
• When designing the power supply circuit for the module, it is often recommended to reserve more than 30% of the margin, so the whole machine is beneficial for long-term stable operation.；
• The module should be as far away as possible from the power supply, transformers, high-frequency wiring and other parts with large electromagnetic interference.；
• High-frequency digital routing, high-frequency analog routing, and power routing must be avoided under the module. If it is necessary to pass through the module, assume that the module is soldered to the Top Layer, and the copper is spread on the Top Layer of the module contact part(well grounded), it must be close to the digital part of the module and routed in the Bottom Layer；
•  Assuming the module is soldered or placed over the Top Layer, it is wrong to randomly route over the Bottom Layer or other layers, which will affect the module’s spurs and receiving sensitivity to varying degrees；
• It is assumed that there are devices with large electromagnetic interference around the module that will greatly affect the performance. It is recommended to keep them away from the module according to the strength of the interference. If necessary, appropriate isolation and shielding can be done；
• Assume that there are traces with large electromagnetic interference (high-frequency digital, high-frequency analog, power traces) around the module that will greatly affect the performance of the module. It is recommended to stay away from the module according to the strength of the interference.If necessary, appropriate isolation and shielding can be done.
• If the communication line uses a 5V level, a 1k-5.1k resistor must be connected in series (not recommended, there is still a risk of damage)；
• Try to stay away from some physical layers such as TTL protocol at 2.4GHz , for example: USB3.0；
• The mounting structure of antenna has a great influence on the performance of the module. It is necessary to ensure that the antenna is exposed, preferably vertically upward. When the module is mounted inside the case, use a good antenna extension cable to extend the antenna to the outside；
• The antenna must not be installed inside the metal case, which will cause the transmission distance to be greatly weakened.

Software editing

• GPIO0 \ GPIO1 \ GPIO2 \ GPIO3 are configurable I/O ports for various application，see more in SI4463 datasheet. It can be floated when not used.

•  IRQ pin can also be disconnected. The SPI query mode can be used to obtain the interrupt status. However, it is recommended to use the external interrupt of the MCU.

• SPI communication rate should not be set too high, usually around 1Mbps.

• Please refer to “Operating Modes and Timing” for SI4463 status switch，the switch between TX and RX should be through Ready, can not be switched directly.

• Re-initialize register configuration when the chip is idle for higher stability.

• For controlling GPIO2 ,GPIO3 externally，pin status is as follows：

  • In tx mode：GPIO2 = 0; GPIO3 = 1;

  • In rx mode：GPIO2 = 1; GPIO3 = 0;
    If the SI4463 is required to control itself, the mode of the configuration pins can be as follows when the program is initialized:

  • SI44XX_GPIO_CONFIG( 0, 0, 32|0x40, 33|0x40, 0, 0, 0 );

Basic application

Basic circuit diagram

6 FAQ

Communication range is too short

• The communication distance will be affected when obstacle exists.
• Data lose rate will be affected by temperature, humidity and co-channel interference.
• The ground will absorb and reflect wireless radio wave, so the performance will be poor when testing near ground.
• Sea water has great ability in absorbing wireless radio wave, so performance will be poor when testing near the sea.
• The signal will be affected when the antenna is near metal object or put in a metal case.
• Power register was set incorrectly, air data rate is set as too high (the higher the air data rate, the shorter the distance).
• The power supply low voltage under room temperature is lower than 2.5V, the lower the voltage, the lower the transmitting power.
•  Due to antenna quality or poor matching between antenna and module.

Module is easy to damage

• Please check the power supply source, ensure it is 2.0V~3.6V, voltage higher than 3.6V will damage the module.
• Please check the stability of power source, the voltage cannot fluctuate too much.
• Please make sure antistatic measure are taken when installing and using, high frequency devices have electrostatic susceptibility.
• Please ensure the humidity is within limited range, some parts are sensitive to humidity.
• Please avoid using modules under too high or too low temperature.

BER(Bit Error Rate) is high

• There are co-channel signal interference nearby, please be away from interference sources or modify frequency and channel to avoid interference;
• Poor power supply may cause messy code. Make sure that the power supply is reliable.
• The extension line and feeder quality are poor or too long, so the bit error rate is high;

Production guidance

Reflow soldering temperature

Profile Feature| Curve characteristics| Sn-Pb Assembly| Pb- Free Assembly
---|---|---|---
Solder Paste| Solder paste| Sn63/Pb37| Sn96.5/Ag3/Cu0.5
Preheat Temperature min （Tsmin）| Min preheating temp.| 100℃| 150℃
Preheat temperature max (Tsmax)| Mx preheating temp.| 150℃| 200℃
Preheat Time (Tsmin to Tsmax)(ts)| Preheating time| 60-120 sec| 60-120 sec
Average ramp-up rate(Tsmax to Tp)| Average ramp-up rate| 3℃/second max| 3℃/second max
Liquidous Temperature (TL)| Liquid phase temp.| 183℃| 217℃
Time（tL）Maintained Above（TL）| Time below liquid phase line| 60-90 sec| 30-90 sec
Peak temperature（Tp）| Peak temp.| 220-235℃| 230-250℃
Aveage ramp-down rate（Tp to Tsmax）| Aveage ramp-down rate| 6℃/second max| 6℃/second max

Time 25℃ to peak temperature

| Time to peak temperature for

25℃

|

max 6 minutes

|

max 8 minutes

Reflow soldering curve

E10 Series

Model No.

| ****

IC

| ****

Frequency(Hz)

| Tx power

(dBm)

| Test distance

km

| ****

Package

| ****

Antenna

---|---|---|---|---|---|---
E10-868MS30| SI4463| 868M| 30| 6| SMD| Stamp hole/IPEX
E10-915MS20| SI4463| 915M| 20| 2.5| SMD| Stamp hole/IPEX
E10-868MS20| SI4463| 868M| 20| 2.5| SMD| Stamp hole/IPEX
E10-433MS1W| SI4463| 433M| 30| 6| SMD| Stamp hole
E10-433MD3| SI4438| 433M| 20| 2| SMD| IPEX
E10-433MD-SMA| SI4463| 433M| 20| 2| DIP| SMA-K
E10-433MS| SI4463| 433M| 20| 2| SMD| Stamp hole

Antenna guidance

Antenna recommendation

The antenna is an important role in the communication process. A good antenna can largely improve the communication system. Therefore, we recommend some antennas for wireless modules with excellent performance and reasonable price.

Model No.| Type| Frequency

Hz

| Interface| Gain

dBi

| Height| Cable| Function feature
---|---|---|---|---|---|---|---

TX915-XP-100

| Sucker

antenna

|

915M

|

SMA-J

|

3.5

|

25cm

|

100cm

|

Sucker antenna, High gain

TX915-JK-20

| Rubber

antenna

|

915M

|

SMA-J

|

3

|

210mm

|

–

|

Flexible &omnidirectional

TX915-JK-11

| Rubber

antenna

|

915M

|

SMA-J

|

2.5

|

110mm

|

–

|

Flexible &omnidirectional

TX915-JZ-5

| Rubber

antenna

|

915M

|

SMA-J

|

2

|

50mm

|

–

| Short straight

&omnidirectional

Antenna selection

Revision history

About us

• Technical support: support@cdebyte.com
• Documents and RF Setting download link: www.ebyte.com
• Thank you for using Ebyte products! Please contact us with any questions or suggestions: info@cdebyte.com
• Fax: 028-64146160 ext. 821
• Web: www.ebyte.com
• Address: Innovation Center B333-D347, 4# XI-XIN Road,Chengdu, Sichuan, China

References

• 串口服务器_数传电台_4G DTU_遥控开关_LoRa/ZigBee/WiFi/蓝牙模块-成都亿佰特电子科技有限公司官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>