Shenzhen Caibo Technology M5 Wireless Charger Car Holder User Manual

Shenzhen Caibo Technology M5 Wireless Charger Car Holder

Package

• W ireless charger *l
• Suction cup holder *l
• User manual *l
• Air vent mount *l
• Type-C cable *l

( Functional Component )

Direction for use

1. Assemble the product and any accessory through a ball head nut and tighten it (compatible w ith ot her bal l head diameter 17mm accessories), and fix it in an ideal positio n. Connect the product to t he QC3.0 car charger (optional) with the data cable, and insert to t he c igarette light er to get electric ity.
2. After t he product is powered o n, the indicator on the both side will light, and the left and right telescopic arms w ill automatically open after 5 seconds to wait for t he mobile phone to be placed; if t he product does not tu rn on red after power on (not t urn on, or flash ) All indicate that there is a problem with the product, please stop using it and return it to the seller for processing.
3. In o rder to ensure t he ef f ic iency and stability of charging, before putting the p hone on, adjust the bottom bracket position of the stand and try to align the cent er position of the back of the phone with the ” ✖” symbo l on t he stand panel as much as possib le. Cell p hones of d ifferent sizes should correspond to d ifferent Stal ls. The best distance for wireless charging is within 6mm and cannot penetrate metal, so it is necessary to avoid using met al or too t hick (greater t han 3mm) mobile phone protective shel ls to ensure fast wireless charging of mobile phones.
4. After p lacing the phone, the left and right clamping arms will automatically clamp t he phone. If the p hone supports QI wireless charging protocol, the product w ill start wireless charging at the same t ime, and the indicator light w ill flash slowly when t he product wireless charging starts; if t he phone does not support wireless charging, t he indicator light will flash quickly for 5 seconds and then t he light goes out. The maximum charging power of t his product is 15W, and t he charg ing ef fic iency w ill vary according to the charging environment and mobile phone.
5. There are two w ays to remove the phone when it is powered on:
   (1) pressing button-auto o pen-take away phone-grips stay open (2) Pull phone down without pressing button in rush-grips stay c losed. A fter taking off the phone, the indicator light is always on and the mount immediately shows the standby stat e. When it is powered off: Pull phone down d irectly. the left and rightc lamping arms keep close.

Air vent mount

Adjust the air vent holding p iece pos ition and the rotatable components position according to the air ventblade position. Insert the blade, Choose the locking switch gears according to the blade thickness. The product is suitable for most air vents, including hor izontal, vertica l, and round air vent.

Suction cup holder

Place the suction cup on a suitable flat position, adjust the angle and press the button to lock the suction cup firmly onto the flat surface. After fixing, the angle and the front-to-back distance can be adjusted at will. TPU suction cup + glue double adsorption, one key to lock.

CC Warning statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B d igital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not instal led and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit d ifferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
This equipment complies with FCC Radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the product and your

Precautions

1. Do not use the p roduct in the car at a temperature above 60 degrees.
2. Do not use th is product in professional racing or extreme off-road driving.
3. When the phone is fu lly charged, it may not automatical ly c lamp on the product.

The guarantee

Products three guarantees valid t ime:From purchasing date (Prevail to the customer receipt date or invoice date),p rovide 12 months guarantee. Product surface man-made damage,acces sories missed are not include in this guarantee. We can also provide the service for you for the product is out of surface or doesn’t include in th is charge.guarantee, but you need to pay the repair charge.

Product Warranty Card

For your rights and interests, please fill in carefully and keep it safely as a pre- repair certif icate! Do not modify the content without authorization, otherwise it will be considered invalid. The company reserves the right of final interpretation of the product after-sales service regulations.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>