Shenzhen Caibo Technology X7 Wireless Charger Car Holder User Manual

User Manual

Package

Wireless charger 1
Air vent mount 1
Type-C cable 1
User manual 1
Adjustable suction cup mount (Optional) 1
Rotatable 3M mount (Optional) 1
Car charger adaptor (Optional) *1

Functional component

Specifications

Name: X7 Wireless charger car holder
Material: PC + ABS
Input: 5V 2A
Output power: SW
Input interface: Type-C
Charging distance: = 8mm
Support specifications: QI wireless protocol
Support QC wireless fast charging equipment (need to match QC charger)
Car charger requirements: QC3.0 car charger
Applicable size: 4.7-6.9 inch mobile phone

Direction for use

1. After power on, the left charger indicator shows red. The 2 clamp arms open automatically in 5 seconds.
2. After putting on a phone, the device will detect charging or foreign bodies automatically. If any foreign bodies are detected, the 2 arms will clamp the phone automatically. (The indicator shows blue when the wireless charging begins, The indicator goes off when impurity detection.)
3. Before placing the phone, center the back of the phone as close as possible to the “S<” on the bracket panel, and try to fit a little closer, so that the phone can be fast wireless charging. The bottom support length is different for different phones. The bottom support has four gears that can be adjusted to a proper position manually.
4. When the product is power on, you can press any one of the 2 buttons on both sides to open the clamp arms, and put on the phone; When the phone is taken off, the indicator shows red, it means the charger is in standby mode.
5. When it’s power off, and the phone is still clamped. 5 buzzings ring in 2 seconds to remind you to take off the phone.(The  built-in super capacitor ensures the clamp arms can open and close 3-5 times in 5 minutes when you press any one of the 2 buttons)
6. Please use a QC 3.0 car charger adaptor for fast charging.

Air vent mount
Adjust the air vent holding piece position and the rotatable components position according to the air vent blade position.
Press and hold the switch to open the clamp and insert the blade. The product is suitable for most air vents, including horizontal, vertical, and round air vent.

Suction cup holder
Put the suction cup holder on a flat place, adjust the angle, press the button, the suction cup will attach to the flat surface tightly. TPU suciton cup+ epoxy dual adsorbtion, one key locking. dual connection rods design, good for storage and package(untra-thin and ultrashort)

Rotatable 3M holder
Clean the place where you want to attach the holder, tear off the protection paper at the bottom of the 3M glue holder, attach it to a suitable place, press it. Use the holder after 72 hours will be better. When the holder is fixed, the angle can be adjusted 360°. TPU+ABS, more fastness attaching to car cambered surface. 3M glue was imported from Japan, adhered more fastness.

Intelligent protection

Over-temperature protection The coil stops charging when the temperature exceeds 60°C, the red light flashes, and starts charging when the temperature is below 55°C.

Over-current protection When the phone exceeds to maximum 1I5W, transmitting terminal limits the power to keep increasing. Over-current protection doesn’t working.

Overvoltage protection The phone may be damaged if the voltage is over 9.5V, which is the maximum output voltage of the Transmitting terminal.

Foreign object detection When the wireless charger detects a metal foreign object,it will stop charging.

Precautions

1. Do not over-squeeze or bump the device.
2. Do not use the wireless charger in severely hot,humid or corrosive environments to avoid damage.Circuit of the device.

Dear customer

Thank you for purchasing this product. To ensure you can get the reliable after-sale service, please kindly read the below instructions carefully:

The products belong to the designated distributor, every column is required and true of registered for this card, otherwise it will be regarded as invalid one. This card is the primary document for the three guarantees for products, please keep properly, no new one for the lost, when you need some technical service, please show this card, we will provide you with quality professional services.

The guarantee doesn’t include the below situation:

1. Can not provide the valid proof or the invoice, except some doc. that can prove it’s still in the valid time. Change this card information for personal.
2. The product batch number isn’t the same as the true batch number or distributor’s seal.
3. Any damages because of no using, maintaining, and storing according to the instructions.
4. Due to accidental disasters, self demolition,man-made damage or failure by the company’s authorized service repair.
5. No name and address, production date or no product certificate.
6. Damage caused by force majeure.

Products three guarantees valid time-From purchasing date (Prevail to the customer receipt date or invoice date),providel2 months guarantee. Product surface man-made damage, and accessories missed are not include in this guarantee. We can also provide the service for you for the product is out of surface or doesn’t include in this guarantee, but you need to pay the repair charge.

Product Warranty Card

No.: _
Date of purchase: __
Dealer name: ____
Dealer: _
Name: _ Telephone: ___
Address: ____

Warranty content _____
Warranty data ____

For your rights and interests, please fill in carefully and keep it safely as a pre-repair certificate! Do not modify the content without authorization, otherwise it will be considered invalid. The company reserves the right of final interpretation of the product after-sales service regulations.

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device, a distance of 15cm surrounding the device and 20 cm above the top surface of the device must be respected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>